PCV Valve hose routing ??

Inferno

New member
I'm getting some smoke and whittle bit of oil coming from my breather on the pcv.. truck has been sitting for a while, I am looking at how the pcv is connected and it looks like boost would just blow right through... and I wrong thinking that hose connected to intake would allow boost to push through ?? I think mine is on wrong altogether...
 

dgoodhue

BuSTeD 4.3
Re: PCV Valve hose routing ??

The passenger valve cover should have a T on it with 2 PCV Valves. The factory correct PCV valves are stamped with E and are one way valves. One PCV valve should come from the throttle body, under boost this valve closes. The other valve goes to the air intake before the turbo. Under boost, the turbo creates a vacuum that operates this valve.

The driver side valve cover has a tube that goes to the air box. You can use a breather on this side to filter the air. This side should only be an air inlet to the engine block if the engine is working properly. If the engine has too much piston ring blowby or a hole in the piston air/smoke will come out this opening because the PCV valve can not keep up with excess air in the engine block.
 

Inferno

New member
Re: PCV Valve hose routing ??

someone deffinitly micky moused this.. driver side is capped... pass side does have a t, but with only one pcv valve and also has a breather.. nothing is going to air box or turbo, only the throttle body.... I'm gonna look more...
 

Jimmy

Banned
Re: PCV Valve hose routing ??

Pull off the oil fill cap with the engine running,rev it up a couple times,and tell me what you see.

Smoke?
 

Inferno

New member
Re: PCV Valve hose routing ??

Short answer... yes :(

I just ran the end with breather into tube before turbo, through a pcv so only under boost will it allow passthrough, then tee, then pcv to throttle body so under vacuum it will allow passthrough, started engine MUCH less smoke from oil cap, but still some... not really smoke though, just a slight haze... but deffinitly coming out and not sucking in or stationary..
 

Jimmy

Banned
Re: PCV Valve hose routing ??

Short answer... yes :(

I just ran the end with breather into tube before turbo, through a pcv so only under boost will it allow passthrough, then tee, then pcv to throttle body so under vacuum it will allow passthrough, started engine MUCH less smoke from oil cap, but still some... not really smoke though, just a slight haze... but deffinitly coming out and not sucking in or stationary..

Hate to say it but your motor is toast: rebuild time :(

Do a compression test to be sure.
 

Inferno

New member
Re: PCV Valve hose routing ??

I know this is very preliminary, but I am going to assume I am doing rings.... I searched "Changing Rings" and got a bunch of cheating girl friends and wifes, not much about actually changing the rings... I think truck runs to damn good to need a complete rebuild... soooo what does one actually order when changing rings.. I assume, the rings.. bearings ?, oil pan gasket, do we do head gasket also ?? prolly a stupid question but I'm at work, depressed that my truck is unhappy with me, and a little high from the fumes I been breathing on the way into work.. and honestly just want feed back to read and depress me more :)
 

mattw

Active member
Re: PCV Valve hose routing ??

I know this is very preliminary, but I am going to assume I am doing rings.... I searched "Changing Rings" and got a bunch of cheating girl friends and wifes, not much about actually changing the rings... I think truck runs to damn good to need a complete rebuild... soooo what does one actually order when changing rings.. I assume, the rings.. bearings ?, oil pan gasket, do we do head gasket also ?? prolly a stupid question but I'm at work, depressed that my truck is unhappy with me, and a little high from the fumes I been breathing on the way into work.. and honestly just want feed back to read and depress me more :)


You are going to get all kinds of advice here but I would do exactly what you have suggested(assuming you don't find any additional damage once you get it apart) which is a simple re-fresh..

Yes, you will need rings and bearings as well as an entire engine gasket set. You will need to replace the head gaskets as well.. For a stock rebuild I wouldn't go to fancy there(some will tell you otherwise).

So, I'd pull the engine, pull the intake, and heads then inspect your cylinder walls. Hopefully there are no deep scratches and only a hone is needed. If thats the case then you can dis-assemble the engine the rest of the way and do the hone yourself with either a ball-hone or the more traditional 3-stone hone.

Install new rings(make sure you gap them to proper specs for a turbocharged engine) and bearings and re-assemble everything.. Thats the route I would take.. You can get it done for a couple hundred dollars and some time...
 

Jimmy

Banned
Re: PCV Valve hose routing ??

I know this is very preliminary, but I am going to assume I am doing rings.... I searched "Changing Rings" and got a bunch of cheating girl friends and wifes, not much about actually changing the rings... I think truck runs to damn good to need a complete rebuild... soooo what does one actually order when changing rings.. I assume, the rings.. bearings ?, oil pan gasket, do we do head gasket also ?? prolly a stupid question but I'm at work, depressed that my truck is unhappy with me, and a little high from the fumes I been breathing on the way into work.. and honestly just want feed back to read and depress me more :)

It "could" possibly be other things.

The compression test will tell.
 

Inferno

New member
Re: PCV Valve hose routing ??

# 6 is 60lbs.. all others are in the 110-130 range..... already got hood off, and wiring harness undone... taking a beer break... goshdarnit just put a new turbo in her too ! (thought that was issue cause there was a little bearing play so I figure oil was getting in there from that...
 

Jimmy

Banned
Re: PCV Valve hose routing ??

# 6 is 60lbs.. all others are in the 110-130 range..... already got hood off, and wiring harness undone... taking a beer break... goshdarnit just put a new turbo in her too ! (thought that was issue cause there was a little bearing play so I figure oil was getting in there from that...

Well at least you got the correct diagnosis,instantly.

How many other websites can do that?
 

mattw

Active member
Re: PCV Valve hose routing ??

You will probably find cracked rings and/or chips missing from that piston.. If you're lucky the cylinder wall will be fine.. Seems unlikely but I've had it happen...
 

Jimmy

Banned
Re: PCV Valve hose routing ??

Sorry man.Good luck on the rebuild.

6>5. It will run so much better once it's fixed :tup:
 

Inferno

New member
Re: PCV Valve hose routing ??

#6 piston was missing some pieces... looks like it's been running real lean there, cleanest head out of em all... (bad injector??) intake gasket looks like it started will have started leaking real soon.. head gaskets look like moses had em on his chariot... block going to get dipped and clean / steamed whatever they do... I'm gonna start searching and googling what pistons / rings and whatever else Ima need.. (other than the obvious gaskets and stuff) Thanks much for the replies.... I just hope to have her back on the road by the 1st...
 
Top