Problem setting the Fuel pressure.

sytyfreak

New member
Hi all,

Well, the stock fuel pump on my truck died and I bought a walbro from Ron Gregory(Thanx man!) I finished the install and the truck started like it was brand new :D . I have a fuel pressure gauge installed on the fuel rail. I went to see what fuel pressure the gauge was getting and it showed 80psi :eek: (with the stock the reading was 20psi) So I did what everyone says I should do to set the stock fuel pressure. I poped out the fuel pressure regulator's vac. line and put it back again. I went to see the reading and it was showing 42.5 PSI :D, but it only lasted for a couple of seconds then the gauge went again to 80 PSI :x. The truck at idle is fine, but as soon as you give it throttle it feels like shit.

I did the same about 3 times with the same results. Any help will be greatly appreciated.

Thanx
 

SY756

New member
80 psi :eek:

Sounds like you have trouble with the fuel return line. Are you sure there are not any kinks or blockages? That's the only thing that I can think of that would cause that high of pressure. Also, when you are saying you popped the vac line off the reg, you do have a adjustible regulator right? Cause if you don't, pulling the line and putting it back on with a stock reg wont do anything.
 

phil2000

New member
i had the same problem, 78psi on the fuel rail, resulting in constant code 45's (too rich).
replaced stock fpr with a atr afpr, problem solved. actually another problems that i tried to track down for a long time has been solved as well: hunting idle, truck dying
when putting from d to p etc....... (probably because the stock fpr not only passed that ridiculous pressure but also had a vacuum leak).

get a afpr, and live will be good again 8) .

regards- phil
 

sytyfreak

New member
SY756 said:
80 psi :eek:

Sounds like you have trouble with the fuel return line. Are you sure there are not any kinks or blockages? That's the only thing that I can think of that would cause that high of pressure. Also, when you are saying you popped the vac line off the reg, you do have a adjustible regulator right? Cause if you don't, pulling the line and putting it back on with a stock reg wont do anything.

Nope, I don't have an adjustable :oops: I have the stock unit :x
 

sytyfreak

New member
phil2000 said:
i had the same problem, 78psi on the fuel rail, resulting in constant code 45's (too rich).
replaced stock fpr with a atr afpr, problem solved. actually another problems that i tried to track down for a long time has been solved as well: hunting idle, truck dying
when putting from d to p etc....... (probably because the stock fpr not only passed that ridiculous pressure but also had a vacuum leak).

get a afpr, and live will be good again 8) .

regards- phil

Thanx for the info. I'm going to buy an adjustable, but I love to solve this problem(if theres anyway) without replacing the regulator. Thanx man
 

SY756

New member
I know it suck's spending money, but get you a adj FPR. You really do need one, even on a stock truck IMO. Hopefully with a new FPR you will solve your high psi problem. That could be the problem, but there is definately some restrition in your fuel return line to cause that high of pressure.
 

sytyfreak

New member
Larry,

I was getting an AFPR with a couple of more things for the truck on Feb. 4 which is my birthday, but I guess I'll have to buy it now. Thanx for your advice.
 

Sy#26

New member
When I first bought my Sy in 1999, the stock FP reg was also stuck around 80psi (is this a common problem?). Replaced w/ adjustable, but the overly righ mixture had destroyed (& plugged) the cat converter. Might want to check that when your FP is fixed.
 
Top