Problem with WB install

sy#2921

BAMF
I went to go hook up my lc-1 and found that there are wires in the slots that i need to use. Does anyone have a pic of the connectors that they could mark which pins (f14 and b9) are those actual pins? Even if I am looking at the connector from the other side I still cant seem to find the correct places.
thanks guys
 

qbnkiller

Conflaguration Specialist
Re: Problem with WB install

If you re-read carefully the instructions (DIGWARE), you will see where you made the mistake. I did the same thing, but on closer inspection, I found the correct locations. I dont have access to the truck ATM, or I would take a few pics for you. It does explain in the instructions what wires are directly across from the spots you need to insert wires into. Also, make sure you have the plug oriented correctly in your hand (looking at the back of the connector, where the wires go inserted, and holding the securing clasp to the top).
 

JSM

Active member
Re: Problem with WB install

F14 is the WB input. As mentioned I suspect you are looking at the wrong pin.
 

sy#2921

BAMF
Re: Problem with WB install

qbnkiller said:
If you re-read carefully the instructions (DIGWARE), you will see where you made the mistake. I did the same thing, but on closer inspection, I found the correct locations. I dont have access to the truck ATM, or I would take a few pics for you. It does explain in the instructions what wires are directly across from the spots you need to insert wires into. Also, make sure you have the plug oriented correctly in your hand (looking at the back of the connector, where the wires go inserted, and holding the securing clasp to the top).

I will look again tonight after work and hopefully get a pic but if i look at the green connector from the back with the locking tab up pin locations f16-f12 all have pins and wires already. This is why i am so confused right now is because I thought the third one in on the upper row from the left which by my count would be f14 should be open and its not. That is why i was hoping someone would have a better pic than what is on digs page.
 

qbnkiller

Conflaguration Specialist
Re: Problem with WB install

also, if you look carefully, it is written on the connector at the edges the pins e.g.
A12
B12
B1
A1

it's a little difficult to see, but on there.
 

sy#2921

BAMF
Re: Problem with WB install

I know i have to be doing something wrong but here is another try. I looked at the connector for the last hour now to make sure i was looking at the correct pins. Pics didnt turn out but i wrote down the wires and location.
starting with pin f16 and working down:
yellow
tan
purple
empty
white w/ black stripe

then with the 24 pin connector b12 towards b1:
black with white stripe
green with white stripe
empty
orange

so from the looks of it and my simple math the pin locations are full no?

what makes this worse is I am a EET and cant figure out some simple wiring
 

VermontTy

Support Our Troops
Re: Problem with WB install

sy#2921 said:
I know i have to be doing something wrong but here is another try. I looked at the connector for the last hour now to make sure i was looking at the correct pins. Pics didnt turn out but i wrote down the wires and location.
starting with pin f16 and working down:
yellow
tan
purple
empty
white w/ black stripe

then with the 24 pin connector b12 towards b1:
black with white stripe
green with white stripe
empty
orange

so from the looks of it and my simple math the pin locations are full no?

what makes this worse is I am a EET and cant figure out some simple wiring
you're looking at the E side of the connector....the F side goes

F14 - plug your wideband in
F15 - 432 Lt Green = MAP sensor
F16 - 472 Tan = MAT sensor

EDIT

WB.jpg
 
Last edited:

skwayb

NWSTP
Re: Problem with WB install

Yes the PIN is open.. make sure if you wbo2 needs a ground to use the b9 pin also (which is open) on the ecm.

Heck if you are confused.. disconnect the ECM completely. With the ECM in your hands.. look down on each connector on the ecm with the pins sticking up at you.. you will be able to see the pin numbers and the Letter of pin for each row. It is very hard to see. Again this is NOT on the connector end with the wires coming out of it. The labels are on the inside of the connectors on the ecm itself with the pins pointing up at you.
 

sy#2921

BAMF
Re: Problem with WB install

Well come to find out at one point my truck did have a wideband in it already. I was right in my first post that there were wires where I needed to hook up the LC-1. I traced them back and found a female 3pin connector similar to what is used for the stock o2 which looks like a disconnect for the one that was in there. I will post results later when I finish the install
 
Last edited:
Top