Proper TPS Voltage???

thunderace31

New member
Like the title says what is proper Voltage for the tps I was doing some tuning in my Ty today and notice a base of 72-74 and a max of 4.47-4.49 Now on my GN we set base at .50-.60 and need to see 4.50 or better at full throttle Im guessing this should at least be max at over 4.50 am I right??

If so the TPS On the truck has 0 adjustment just 2 bolts and no slots to move it around to set it. Or at least the one on my truck doesnt have any slots.

Please advise Id like to get this set up right if it is wrong what needs to be done??

Thanks
 

leadfoot

Member
Re: Proper TPS Voltage???

There is no proper voltage. It is (theoretically) 0V when closed and should (theoretically) be about 5V when wide open. There are no adjustments.

Put the sensor on a DVOM and turn the sensor s l o w l y to see if the resistance increases linearly. If it jumps around too much to pot is shot.

Do a search for more answers...
 

thunderace31

New member
Re: Proper TPS Voltage???

There is no proper voltage. It is (theoretically) 0V when closed and should (theoretically) be about 5V when wide open. There are no adjustments.

Put the sensor on a DVOM and turn the sensor s l o w l y to see if the resistance increases linearly. If it jumps around too much to pot is shot.

Do a search for more answers...

It doesnt jump around much at all its very linear from what I can tell. But it never goes over 4.47-4.49 volts :roll:
I did a search and came up with noting hence the post Ill try searching again
Thanks
 

TY0618

Member
Re: Proper TPS Voltage???

At WOT, 5.0 would be ideal, Ive never seen one at 5.0, always 4.3-4.8....I'd say you values are good.
 

thunderace31

New member
Re: Proper TPS Voltage???

At WOT, 5.0 would be ideal, Ive never seen one at 5.0, always 4.3-4.8....I'd say you values are good.

I got a new one yesterday just to be safe and now have .73 base and 4.51 max also checked that the throttle was opening all the way and it is :) I guess thats as good as shes going to get :roll:
 

TY0618

Member
Re: Proper TPS Voltage???

I guess you mean ohms, not volts.....Thats what I understood. sorry if you meant volts.
 

dgoodhue

BuSTeD 4.3
Re: Proper TPS Voltage???

The TPS doesn't need to be adjusted or slotted. The ECM automatically "zero's" the TPS.
 

thunderace31

New member
Re: Proper TPS Voltage???

The TPS doesn't need to be adjusted or slotted. The ECM automatically "zero's" the TPS.

It needs to see the high Voltage to add fuel from the chip trust me after playing with it I have seen fuel increase and also made a better run on Datamaster :)
If the computer zeroed it then it would not be needed at all
 

dgoodhue

BuSTeD 4.3
Re: Proper TPS Voltage???

It needs to see the high Voltage to add fuel from the chip trust me after playing with it I have seen fuel increase and also made a better run on Datamaster :)
If the computer zeroed it then it would not be needed at all

Our truck aren't fuel off of TPS. It only needs 62.5% of TPS to enter power enrichment.

If you seeing a difference on scan tool, its a coincidence.
 
Re: Proper TPS Voltage???

Here's a post from Daron about TPS values from way back...

http://www.syty.net/forums/showpost.php?p=18402&postcount=11

When you start your truck, the ECM takes the closed throttle reading ( somewhere below 1.1 volt) and calls this voltage level "0%". From that level it only takes approx. 3.15 volts for the ECM to report a "100%" throttle opening. So, if your truck is like mine, the TPS drops .6 volts at closed throttle. All you would need is aprrox. 3.75 volts at WOT for the ecm to report a 100% throttle opening.
Mr. Sealander was kind enough to beat me over the head with that years back, after I had quoted the SyTy supplement. The SyTy supplement would lead you to believe something totally different than the above
 
Top