Rebuild with forged internals help

wexy21

You're Boosted!
Since it's a good idea to rebuild after finding out my turbo ate some plastic and destroyed it, sending oil into the intake for god knows how long...I figured on putting a forged crank, pistons, and rods in. This truck is pretty hard to find parts for. I have a bodyshop friend of mine giving me some phone numbers for people in town. But I like buying off the internet. So if I were to rebuild using forged parts, does anyone have some links or suggestions?
I want this to be a good daily driver and reliable...but also upgrade a few things. Right now I'm talking to a shop that rebuilds turbos. They are looking into the part numbers I found off this link: http://www.syty.org/old/modlist.html I'm also looking into tuning this truck right, but for right now, I just need to get the internals purchased and put in. Has anyone ever mentioned how tight everything is in the motor compartment! Damn!
 

Icarus-54

Donating Old Member
Re: Rebuild with forged internals help

Forget the forged crank unless you have 3500 bucks laying around.A cyro treated stock crank will take you up to 700 hp.So will eagle rods and either srp or je pistons.Any thing bigger and youre talking bow tie block,forged crank,ect.and a really fat wallet.Any sy ty combo must be built right,balanced right,and tuned right to last.Anything you would need is carried by most of the vendors on his site.
 

wexy21

You're Boosted!
Re: Rebuild with forged internals help

Wow...I'll pass on the forged crank. I don't need to go that fast anyway.

So, cryo treat my crank, eagle rods, and a set of srp pistons sounds a little more in my budget.

I guess I should be checking out the vendor section here?

Also, buying these parts and putting them wouldn't really require them to be balanced right? My motor didn't break or anything, it ran good (just bad turbo) and smooth before I tore into it. So I think I'm good on just swapping piece for piece?
 

JSM

Active member
Re: Rebuild with forged internals help

Also, buying these parts and putting them wouldn't really require them to be balanced right? My motor didn't break or anything, it ran good (just bad turbo) and smooth before I tore into it. So I think I'm good on just swapping piece for piece?

No, not at all.

You looking to change the rods and pistons, even brand and type. Think about it do you think the weights will be identical to what was in there before?
 

wexy21

You're Boosted!
Re: Rebuild with forged internals help

What do you suggest? Should I just leave my internals alone since they are fine, and just clean everything really well? I could part with around $2000 to get everything (excluding price for a turbo), but wouldn't have access to get everything balanced. I'm doing this in my garage.
 

JSM

Active member
Re: Rebuild with forged internals help

As many of us have experience building a syty motor right and with a budget seem to conflict.

I personally balance any motor I take apart, even stock internals. The $200 or so is worth it for me.

If you budget is really tight, you might be better off finding a running motor to put in for now.
 

Ry368

one mile = 5280 feet
Re: Rebuild with forged internals help

Somebody on here has a stock stroke forged crank for sale.....Hacking maybe?
 

wexy21

You're Boosted!
Re: Rebuild with forged internals help

Well I'm thinking that if I have to pull the motor, I might as well not rebuild and just clean and make everything work right. The motor ran fine, it just needs some attention and upgraded parts (vacuum lines, turbo, etc). I can buy a motor and build a strong runner while I drive this one, and then do a swap later on. I was just thinking that since I have the motor mostly exposed I should rebuild.

I do plan to have the heads and upper/lower intake cleaned, or boiled, whatever is needed. Maybe replace the valve springs too.
 

dgoodhue

BuSTeD 4.3
Re: Rebuild with forged internals help

I don't think you need to rebuild your engine or tear it down because your turbo sucked in some plastic (crossover tube). Anything small enough to pass through the intercooler probably just burned up.
 

wexy21

You're Boosted!
Re: Rebuild with forged internals help

You're right Dave...Luckily the IC caught it all. It needs a good flushing though. With all the oil blowing thru the intake I wanted to see what the innerds looked like. It's full of sludge (130,000mi), but nothing looked "bad". The pistons look fine as I said. Glad you guys are here to help though. I think it would be wiser to just build up an aftermarket block, and then just part this one out. But in the mean time, drive and enjoy this one.
 
Top