Regarding Scanmaster, Datamaster, Tunerpro...

MAK

New member
I am glad to see more tools opening up for the home tuner. I'll be honest - I have no clue when it comes to tuning. It can be learned with a little time, which I will gladly invest. I am wanting to purchase something to help me understand the "behind-the-scenes" workings of our trucks and do not want to get too much too soon. This thread is helping me decide which route to go but there are still a few things I am unsure about. As I always do, I have researched everything too much and am starting to get confused as to which direction to go in. If Eric or someone else could chime in and offer some advise it would be appreciated.

From what I have read here, I am thinking I should go with Scanmaster, a velosyty chip, a 3 bar map sensor and Tunerpro. It appears that Tunerpro is more compatible to Scanmaster and I believe it does the same sort of logging that Datamaster does (please correct me if I am wrong). Having a small device to monitor everything, all of the time, appeals to me. Using Tunerpro would come into play when I needed to go more in depth. I am on a budget and am not looking to make huge power. I just want to make the TY run safely and hopefully avoid future unforeseen problems.

Are the above additions a good start or would something else be a better option given my desired outcome? I am ready to make the purchase, either way.

I have a mostly stock '93 Typhoon with an RPM CAI, 255 Walbro fuel pump, stock 2 bar MAP sensor, MSD ignition, 3" exhaust and Magnaflow Cat.
 

Quickstop [UK]

Combating adversyty.
Re: Regarding Scanmaster, Datamaster, Tunerpro...

Scanmaster, Datamaster and TunerPRo all read data from the truck. The ALDL link is basically a serial data port that transmits the data to whatever device wants to read it.

Your plans are good but you will need a way to make changes to the chip if you want to tune yourself. The most popular method is the Moates Ostrich.

This plugs in to the ECM but I'm not sure how it works with the VeloSyTy chip. Perhaps you can get the BIN tuned by Eric Sy GN and load that on your Ostrich instead of mailing a chip back and forth.
 

Flyin Ryan

hated cuz he drives fords
Re: Regarding Scanmaster, Datamaster, Tunerpro...

The turbotweak chip does allow you to adjust your timing,fuel,boost,etc all with your gas peddle as well but to see the variable change you'll need a scan master or laptop/tuner pro/data master setup.

The tuner pro,ostrich,g1,laptop,Alda cable way will allow you full control and you'll be able to make any and all changes you could want but it requires a learning curve apposed to the tuned tt chip and scan master.

Either way is good but money and time wise I'd say the tt way would be best depending on your situation/needs/goals
 

MAK

New member
Re: Regarding Scanmaster, Datamaster, Tunerpro...

Thanks! So as to all of the stuff I listed, none of it can make the changes to the tune. Got it. In order to make the necessary changes (without going crazy) I want a simple, user-friendly way to change basic parameters, if absolutely necessary. Ostrich seemed to be good, but I want to make sure I get something that works well with the whole package (Scanmaster, Velosyty chip, Tunerpro). In a perfect world, the chip would not need to be changed after having it set up for my TY's configuration.
 

Flyin Ryan

hated cuz he drives fords
Re: Regarding Scanmaster, Datamaster, Tunerpro...

The velosyty/scanmaster setup allows you to change the tune. Tuner pro isnt needed unless you want to datalog rather then pay atte tion to your scanmaster. To use your o2 with the setup plug it into the scanmaster.

To change your tune withtunerpro you'll need a laptop,ostrich,g1,tuner pro. To see data and or data log with this setup you will need an Alda cable as well. If your tying in your wideband o2 you'll need to patch and wire o2 to ECM.
 

MAK

New member
Re: Regarding Scanmaster, Datamaster, Tunerpro...

Ryan - I did see where you can change the settings on the Velosyty chip using the gas pedal. That would probably be sufficient for the basic tuning I would be doing if required.

Every time I think I have this all figured out another option comes up. This time Scanmaster....:banghead:

So Scanmaster, Tunerpro or Datamaster for logging, Velosyty chip, and Ostrich (or similar) eventually for making complex changes to tune. I have a laptop already for use when needed for logging.

Am I missing anything for now? Any other recommendations?
 

MAK

New member
Re: Regarding Scanmaster, Datamaster, Tunerpro...

Ryan - I missed your last post before I posted mine. Thanks for the help.
 

Quickstop [UK]

Combating adversyty.
Re: Regarding Scanmaster, Datamaster, Tunerpro...

Have you got a wideband O2 gauge? You'll need that to tune properly.
 

BoostedSUV

Active member
Re: Regarding Scanmaster, Datamaster, Tunerpro...

Ostrich is the easiest way to update your tune but you could get a Moates Flash N burn and burn your own tunes for cheaper than an Ostrich. juist in volves loading a .bin (tune) and burning it to a chip and dropping it into the adapter in the ECM. That's just another cost effective way to load tunes.

Flash N Burn works as a standalone chip burner and in conjunction with tunerpro
 
Re: Regarding Scanmaster, Datamaster, Tunerpro...

Every time I think I have this all figured out another option comes up. This time Scanmaster....:banghead:

Am I missing anything for now? Any other recommendations?

I wouldn't really look at the Scanmaster unit as another option, but rather an added initial safeguard. For me, just cruising around in my Ty, I have no idea what's happening with the inner workings of the vehicle and if it's running correctly. With the Scanmaster plugged in, while cruising around, if a problem came up, it would tell me. I then could unplug the Scanmaster, plug in Datamaster, and with a code59 setup, I could then fix the problem on the tuning side and also fix what might be wrong under the hood. When I get my tuning stuff, I'm going to do code59, but I will also have a Scanmaster plugged in when I'm not monitoring and tuning things with the laptop and Datamaster.
 

MAK

New member
Re: Regarding Scanmaster, Datamaster, Tunerpro...

So many options....

If there was a Powerlogger app to work with the Typhoon that have the Velosyty chip, that would be good to start with until I can get more familiar with the parameters. It seems the Powerlogger is only available for GN's. Is this correct or will that one work for us as well?

Quickstop - I do not a wide band sensor.

Typhoon Noob - I agree 100% about Scanmaster. It is good to see what is going on NOW, not just when you have the logger connected.
 
Re: Regarding Scanmaster, Datamaster, Tunerpro...

Typhoon Noob - I agree 100% about Scanmaster. It is good to see what is going on NOW, not just when you have the logger connected.

Definitely, this is the next thing I'm getting for mine.
 

Eric Sy GN

Donating Member
Re: Regarding Scanmaster, Datamaster, Tunerpro...

For someone such as yourself, with little tuning experience, a Scanmaster would be a good starting point. The Velosyty chip will give you decent basic tuning capabilities and other advanced features. As you gain experience, you may decide to do your own full tuning starting with a stock chip or code59, etc.
Eric
 
Top