Request: Timing table

wildphil

I Love My Ty's
I would like to look at the timing table from someones tune that had a fairly quick truck. I was wanting to look through the table and see how your advance compares to mine . I know the timing for one truck would not be ideal for another. Was really wanting to look at the pattern of high or low advance numbers for the changing load on the engine.
 

sytyguy

Moderated User
Re: Request: Timing table

It's more than F1 to consider mind you. Here's the F1, F3, & F80 tables for my starter stock code59 bin.

2j2bwg7.jpg
 

wildphil

I Love My Ty's
Re: Request: Timing table

Thank you Michael. I know very little about the timing aspect of tuning. Only basic knowledge. But I am trying to learn more.
 

mattw

Active member
Re: Request: Timing table

Interesting.. My F3 is set to all -1.76 so its effectively doing nothing.. I like the idea of pulling timing when the intake temps get high...
 

wildphil

I Love My Ty's
Re: Request: Timing table

Interesting.. My F3 is set to all -1.76 so its effectively doing nothing.. I like the idea of pulling timing when the intake temps get high...

I may be all wrong. But it looks like to me. Set at -1.76 on all cells. pulls 1.76 degrees of timing from what the F1 table is set at. Well I guess the F80 is also in effect and would change the value also.
 

mattw

Active member
Re: Request: Timing table

I may be all wrong. But it looks like to me. Set at -1.76 on all cells. pulls 1.76 degrees of timing from what the F1 table is set at. Well I guess the F80 is also in effect and would change the value also.


I'm pretty sure you are correct.. When I said I does nothing I just meant that it does not make any adjustments based on boost and intake air temp...
 

wildphil

I Love My Ty's
Re: Request: Timing table

Michael's F1 table looks more like what I would guess a F1 table should. Being a starter bin it is conservative of course. But most other F1 tables I have looked at Timing starts more adjanced. Then as engine load is increased. Drops way off in timing advance.
 
Last edited:

sytyguy

Moderated User
Re: Request: Timing table

The F3 I rewrote to allow an increase in timing as temps get cold and to retard timing if temps get too hot (IC pump failure, heat soak, EGR soak, etc...). When I start out tuning, I usually zero out F3 and F80 to gain some clarity on spark advance.
 

wildphil

I Love My Ty's
Re: Request: Timing table

Do you advance timing until you get KR and then take out a degree of timing?

Does the fueling table also come into play while adjusting the timing?
 

mattw

Active member
Re: Request: Timing table

Can someone explain to me what F80(PE Contribution to Spark Advance) does?
 

randy merritt

Donating Member
Re: Request: Timing table

http://www.syty.net/forums/showthread.php?t=83386&highlight=code+powerpoint

Here is a good tutorial on code59 that may answer some common questions. I don't know if you have already seen this or not, if so, I apologize in advance. This was very helpful to me to understand how code59 works.

Also there are lots of .bin files on the code59 website where you can look at various timing tables. I took a fuel table from one .bin and merged it with a timing table from another .bin to arrive at my starter .bin. It seems all of the starter .bins are very conservative, with good reason.
 

sytyguy

Moderated User
Re: Request: Timing table

Can someone explain to me what F80(PE Contribution to Spark Advance) does?
PE (Power Enrichment) is active when all scalar requirements are met (above kpa, tps, cts, etc... mins), and this table (F80) will add spark advance in accordance with the corresponding cells within F80. So, think of it this way.....you pass someone on the highway and get into boost with 3/4 throttle, activating PE mode. You will see advance added (and changing based on rpm if the cells differ).

This was an old school way that we (tuners) used to add in timing for racing. Keep the entire tune the same and alter F80 for timing and F77 (F77x now) for fueling. I remember burning about 15 chips for Waller at Nationals back in 1999 (or 2000 can't remember) and only altering those 2 tables. Effective for that desired purpose.
 
Top