scared to install chip

TYGUY

New member
i want to install my new chip and 50# injectors, but i get a check engine light every now and again its a EGR code 32 i think. i have fixed all my vac hoses and replaced the EGR valve. and it fixed it until today. i am going to scan it tomorrow to double check what code. if i install the chip i think it could fix my problem, if it turns off the EGR. its a turbo time chip. what should i do? should i try it?

Dustin
 

chelo

filthy sy
Re: scared to install chip

I dont have a turbo time chip but before i ever installed my ultimate. I did get a code 32. Only while on the freeway. I installed the ultimate and never more code. I've never felt a hesitation even when the code came on. I say just install your chip.
 

Flyin Ryan

hated cuz he drives fords
Re: scared to install chip

If it's coded in the chip to disable the EGR then it will not give you a code for the EGR not functioning properly or being disconnected so go for it.
 

TYGUY

New member
Re: scared to install chip

i think i might install this weekend, do you see a huge perf. gain when adding the injectos and chip?
or was it more of a safety thing with the injectors and chip?

Dustin
 

VermontTy

Support Our Troops
Re: scared to install chip

You probably won't see much of a gain by just tossing in injectors unless the chip modifies your timing to take advantage of your ability to provide more fuel (you have a Walbro 255 fuel pump or something other than stock, right?) Are you planning on running anymore than stock boost? If so, you'll need a 3-BAR MAP sensor as well. Just tossing on parts like injectors, etc. usually doesn't buy you anything except "capacity". When you increase boost and timing to take advantage of that new capacity is when you start making power.

A little more reading from a similar issue visited recently.

http://www.syty.net/forums/showthread.php?t=34334

EDIT

Oh, and it seems that most aftermarket chip setups out there have EGR disable as kind of a 'standard' feature....We can give you names of members that could custom-burn your chip with EGR disable if it didn't come through like that.
 

TYGUY

New member
Re: scared to install chip

i have the racetonix and 255. i have a 3 bar. and will be adding alky and a manuel boost controller.
with the chip and injectors. the only reason i have not pu them on yet is my EGR code, and i want to install a WB02 before i go too much further.

Dustin
 

blk00z28

Forced to by choice
Re: scared to install chip

Boostedpimp said:
If it's coded in the chip to disable the EGR then it will not give you a code for the EGR not functioning properly or being disconnected so go for it.

And you can even go as far as to remove the EGR off the motor. Just dont go pulling all the vac hoses off. Just take the main line going to the EGR off and then put a cap on it.

I made my own little EGR block off plate a few months ago. I used a little to thin of metal. So make sure you get a thick piece of metal or at least shorter screws. (I used the stock EGR screws because they look good on the motor..but they are too long and bottom'ed out in the holes, which I'll be replacing here soon. You can also ask Hood about is EGR block off kit
icon_wink.gif
)
 

TYGUY

New member
Re: scared to install chip

i have a plate fom GM. i just dont want my TY to run bad... it ran pretty bad when i got it home.....and i have put a ton of $$$ and time into it since.....now it is running pretty good. i added a ton of "bolt ons" and tune up parts...steering/suspension ..ect... so i just want to be cautious.
so does anyone know for sure uf the P.long chip disables the EGR?

D
 
Top