Snapped crank what to do??

akwilks

Mr. Keith
I may have to get a new block, crank, and internals but I dont know this for a fact until I hear from the mechanic tonight.....If this needs to be done should I look for a specific block and crank? One that doesnt break when all new parts are used and only a thousand miles is put on it?? I just bought the 93 Typhoon and its gorgeous but now its just a trophy....all I can do is look at it and think of what could have been.....I need help badly and soon....the engine was pulled today and I need to know whether I should let the shop find my parts or should I order them myself.....Thanks in advance..

Arn :(
 

93ty475

Donating Member
Re: Snapped crank what to do??

I may be wrong, but a stock (treated is better) crank can take quite a beating before breaking....unless your goals are to set the world on fire, you should be ok with a stocker....you might want to look into billet main caps and arp hardware to aid in keeping the crank in its place though....I'm sure Mike Lee can help you with all of the above.....just look the latest model 4.3 non balance shaft engine you can find and you should be ok....
 

dgoodhue

BuSTeD 4.3
Re: Snapped crank what to do??

You might want to figure out why it snapped. Do you have a built motor with a lot of mods or few bolts on? If its the later, mostly you truck was out of tune...
 

VermontTy

Support Our Troops
Re: Snapped crank what to do??

My stock crank blew in two after the previous owner removed the cat and put in a Kenne Belle chip. Two perfect ingredients for catastrophic knock.

I've heard the same, that stock cranks should take you to 600, 700hp. You had a crank on the verge of shitting the bed, or have some serious knock.
 

akwilks

Mr. Keith
Re: Snapped crank what to do??

Thanks for the advice....The truck is modified with 50# injectors/hi flow fp, ext wastegate, adj boost controller, GN turbo, no cat, a Dynotech chip??.....This is what I was told...The truck was called the "White Devil" so that in itself implies alot...How do you snap a crank with a fresh motor with less than 1k miles on it? Well I've never driven a Typhoon until now and just read about launch takeoffs so I am certain I didnt stress the motor...I find out this afternoon the fate of the block and its internals....I'm hoping its not too bad...

Arn
93 Typhoon....the Ty will rise again!!!
 

nightdiver

Active member
Re: Snapped crank what to do??

VermontTy said:
Why nitride vs cryo?
Isnt it the same ?

Arn
i snapped a shaft a few years ago and it was a used shaft that i bought with a span bearing in its history(i didnt know) . Other than that it could brake from vibration. Dont think about it, shit happens
Falco has a shaft in three pieces (or four) but he was racing
 

VermontTy

Support Our Troops
Re: Snapped crank what to do??

They are very different. Nitriding treats the outer layer of the part (usually under 1mm thickness) to increase resistance to wear, etc. It is a surface hardening technique. Cryo treating treats the entire volume of metal, realigns the grain structure of the metal to relieve stresses "built in" to the part when it was constructed. Getting rid of the stresses from build can keep the part from expanding, bending, etc., and that is how it reduces wear and breakage.
 

nightdiver

Active member
Re: Snapped crank what to do??

Whats best then ?
We know that hard metall isnt flexible under torque so it might brake easier ... or not . I think we can only guess
Got any idea ?
 

bezerk

New member
Re: Snapped crank what to do??

nightdiver said:
Whats best then ?
We know that hard metall isnt flexible under torque so it might brake easier ... or not . I think we can only guess
Got any idea ?

cryo helps to get the stress out of the material.
nitriding is making it harder on the outside.
 

akwilks

Mr. Keith
Re: Snapped crank what to do??

I found out last night that the engine was built with flat top pistons......shame on them!! The place is called Dynotech and they are in nj. They said they have built many ty/sy motors and knew that my particular truck ran good when it left....That might be so but the rods were hitting the sides of the engine not to mention they put 12:1 pistons in it.....Its beyond its warranty but I wonder if I can still take some action against them for not building a proper turbo motor.....I have to replace everything!!!

Arn
93 Typhoon
 

ghettosled

SYTY SUPERSTORE
Re: Snapped crank what to do??

well i seriously doubt they built you a 12:1 motor, atleast not with flat tops and a production cylinder head.. And how were the rods hitting the sides of the engine? This is basically impossible with a stock stroke crank.

Also as for the nitriding, different companies have different proceedures. The company we now use treats our cranks just over .035" from standard size so even if you have to re-grind the crank to .020 under there is still treated metal underneath.
 

akwilks

Mr. Keith
Re: Snapped crank what to do??

It may sound unbelievable but its true....I saw the pistons myself and the scarring on the block where the rods connect with the crankshaft....I had to videotape it because who would make such obvious mistakes when building a motor?? 2 of the eagle rods were bent, you could see all the metal deposits inside the motor from the rods hitting the sides, and the crank split about 6 to 8 inches from where the flywheel bolts on...One thing I know for sure, the pistons where not dished, they were flat with small half circle depressions in the center.....either way I'm getting another engine put together and she should be ready monday.....

Arn
93 Typhoon
 

nightdiver

Active member
Re: Snapped crank what to do??

Im dying to see some pics man. What were they thinking when they did this motor ?
and she should be ready monday....
No way.....this is syty related.How bout next month ;)

and dont through away the pistons. Think about it and you might use em in an engine combo with high compression, 300-305* solid cam and low boost. It will be a SOB to drive
 

93ty475

Donating Member
Re: Snapped crank what to do??

akwilks said:
2 of the eagle rods were bent

:eek: I've yet to hear of bent eagle h-beam rods in a syty.....they must have bound up after the crank failed....I'm not the expert on high compression stuff, but the few high compression pistons I have seen were not flat....they had very pronounced center sections to them.....12:1 doesn't seem right....I would think a stock crank would break before eagles would bend but in your case both failed......whatever the driver did, he was likely pinging to have destroyed the crank and rods......good luck and emphasize on the little stuff while you do your r&r and new build, is my best advice.....
 

dgoodhue

BuSTeD 4.3
Re: Snapped crank what to do??

Flat tops and production heads usually around 9.5:1 compression. This one of the reasons, why many of us recommend looking at a scan tool when first purchasing a truck. you must have had massive amount of knocks. Your not the first truck with the wrong pistons, If you had turn the boost down to 8-9 psi it probably would have lasted...
 

ed hess

race or get outta the way
Re: Snapped crank what to do??

ghettosled said:
well i seriously doubt they built you a 12:1 motor, atleast not with flat tops and a production cylinder head.. And how were the rods hitting the sides of the engine? This is basically impossible with a stock stroke crank.

mike
i have not seen 12-1 with stock cyl head. but! i have seen flat top pistons at zero deck and angle milled heads with the right cc chamber come in under 12-1. he doesnt say above what the gasket thickness was but yes its entirely possible to use flat tops, zero deck, milled heads and proper gasket thickness and end up at 12-1 or so. just run the numbers and you will see. of course you need a tuner that can tune hi cr with a turbo. ;)

i have to wonder what engine mangement system was being used here.
or did he say it was a chip? detonated itself to pieces.

if he wants a billet crank i still have have that one i got from crower.

I recall somebody telling me that dynotech had a truck they put together that they thought was going to kick my 6 ...untill we ran even faster. lol
 
Top