Stock Boost Control issues

dgoodhue

BuSTeD 4.3
On track runs, my truck overboosts pretty bad in 3rd gear, (for instance T115 I am getting 19-20psi through all of 3rd gear).

Previous owners of my truck have not modified my truck at all and is mostly original parts/sensors.

How would you recommend I go about fixing this issue? I know I can lengthen the wastegate, but I don't want to band aid the problem. Can the waste gate actuator be sticky? how do I test it? Could this be a problem with the soleniod, could it be dirty clogged? Could the wastegate be sticky? Clogged?
 
G

Guest

Guest
That is exactly what you want to do is lengthen the wastegate rod by about 5 turns in your case. Now when you go to increase boost only go by 1 or 2 turn increments... then see where your at ill bet it will be close to inline.... the stock adjustment is 7/8th of the wastegate pin showing through the rod atachment....
HTH Dan
 

dgoodhue

BuSTeD 4.3
cheatham2492 said:
the stock adjustment is 7/8th of the wastegate pin showing through the rod atachment....

Would the factory setting be that far off that I would overboost 4-5 psi? I am 99.9% sure the wastegate is the factory setting.

Anyways is there a way to test the wastegate accuator top make sure it works properly?

Is there a way to test the boost soleniod? or is this not the problem...

I have read of some owners cleaning the wastegate or is this a real PIA to do?
 

syclonekid43

New member
if you unplug the boost soleniod you should ony get around 10 psi of boost my truck wasnt boostin alot for me i played with the rod and it got alittle bit better
 

Falco

Donating Member
Dave,

To check you actuator, just loop out your solenoid, connect the boost source on the compressor side to the actuator directly with a vacuum hose. You should get consistent 9-11 psi all the time. This way you can rule out the actuator.

To clean your wg you should remove the turbo, so I'd say it's not so easy to do.

If the actuator seems to be right after the above test I'd try to lengthen the wg rod. You should also check that the wg moves freely with the rod disconnected. Sometimes it becomes sticky only when hot. Get a glove and try to move it after a run.

Later,
 

Falco

Donating Member
Jeremy,

In my mind the stiffer spring means slower wg reaction which means better chance to overboost...

Later,
 

sy2185

New member
No debating that, My problem wasn't overboosting, it was the 11psi to 16 psi fluctuation with the boost target at a solid 14.3. Most people have either boost creep , mis adjusted WG rod or the problem like I had. Just wanted to get the pics out there.
Jeremy
 

Zac

New member
sy2185 said:
No debating that, My problem wasn't overboosting, it was the 11psi to 16 psi fluctuation with the boost target at a solid 14.3.
Jeremy

This is the problem that I have been seeing on my truck. It happens the most when the weather is hot & humid. What kind of spring is that? Did you get it at a local hardware store?

Thanks,
ZAC
 
G

Guest

Guest
"On track runs, my truck overboosts pretty bad in 3rd gear, (for instance T115 I am getting 19-20psi through all of 3rd gear). "

When to work in VAIL and going up I-70 @ 3/4 throttle my boost gauge read 27.1PSI on the new SPA gauge i just bought..... :eek: :eek: " Yes i let off"
I changed over from STG to the Hypertech chip for a moment the waste gate tables very from chip to chip also.. I never got over boost with the STG. Adjust for the chip..... its not stock anymore. check the actuator with a handpump. it should start moving the rod around 10psi.. I have bein dealing lack of boost on the t45 and now 27.1+ with the stocker..
Just vomiting words cheatham
 

dgoodhue

BuSTeD 4.3
This topic has been helpful, my accuator appears to be good. I tried looping it out and checking it with a mitivac. It also works much like the spare one I have.

Is there a way to check my boost solenoid, could it be clogged up or sticky? It is missing the filter. Could I try to clean it out or should I rig something up to test it out of the truck?
 

jwaller

Evil Genius/SyTy Guru
you can use a 9V battery. and some vac line. it is easy to test. but hell they only cost ~15 bucks... so just replace the damn thing.
 

Tooky

Serious about performance
When you guys say with the WG Solenoid unplugged you should get between 9-11 PSI, do you mean on the iniital spool or that it should never go past 11 PSI even through the top of 2nd and 3rd?

My trucks' boost has always looked like a roller coaster on DataMaster (I would prefer flat-line at target) and now I'm wondering if my WG Actuator is the source of my woes. When I unplug the solenoid, the boost will hit 9 or 10 at first then slowly rise to 13 and such, depending on the length of the WG rod. It seems like the WG just can't keep the boost down to base and it wants to raise no matter what.

Any help appreciated,
 

Falco

Donating Member
Josh,

When I looped out my solenoid, I got 9.7 PSI in 1st and it never went above 10.5 PSI till 95 MPH. So I'd say you should not get 13 PSI on it...

HTH,
 

dgoodhue

BuSTeD 4.3
TookyCat said:
When I unplug the solenoid, the boost will hit 9 or 10 at first then slowly rise to 13 and such, depending on the length of the WG rod. It seems like the WG just can't keep the boost down to base and it wants to raise no matter what.

I am just thinking out loud

-Bypass the Boost Soleniod, to make sure that isn't acting funny
-Maybe your rod is still too short?
-Maybe the accuator has an air leak that bleeds off?
 

Maxtor

New member
I am running a mitsu 20g 12cm2 w/integral stock spring WG. ECM boost control has been a real headache for me - runs at nats showed fluctuation from 12-20 PSI at shifts. It felt like I was driving a frickin rollercoaster.

After nats, I went back to a 15psi mitsu actuator and starting working on the computer WG control code - I got it to hold within 4 PSI running the 17 psi (ultimate) program but still am not happy, it needs more tweaking.

During all this, I bought a check valve controller from boostvalve.com for around $35. With the 15 psi actuator in place and this valve set to give me an additional 2 psi (17 psi total), boost fluctuated a maximum of 0.7psi on datamaster from 0-115 MPH. I also made runs at base boost (15psi), 16, and 18 psi and it held equally well. No boost creep - no spikes.

Now I need to remember why I was messing with the ECM for boost control...... this sure is easy.
 
Top