switching from Ultimate to code59?

2500avalanche

Well-known member
OK,
I am new into this, but after talking to Brandon (Aeroking), I finally am starting to understand about this subject.
I am wanting to go faster (of course) after my rebuild. I would like to put on bigger injectors (50#), and get a larger turbo. The ultimate I have does not support this.
So, I would need to go code59, or basically get a chip programmed for the truck. To do this, I am going to need to purchase and Ostrich 2.0, correct? Or what other/styles are out there to help someone do a chip burning. Is this difficult to do? Any help/thoughts would be great as I am new into this area, but want to get the most from my truck (before the rebuild, I loved it, but thought it was not all it could be...)
Thanks guys
 

WyoSyclone

Active member
Re: switching from Ultimate to code59?

There are a couple of good threads over on the Code59 site that list everything needed to get started - I think there is a thread here too that lists the parts.

Basically, for real-time emulation/tuning you need a G1 chip carrier, a ZIF socket (makes things easier), and an Ostrich, and the laptop.

For burning tunes one at a time and testing them you could get by with the G1, definitely the ZIF, and a Flash n' Burn chip burner, and the laptop.

You need TunerProRT to do the programming, and it really does work best to have Datamaster for logging, although V5 of TPRT does about the same I haven't had time to work with it.

You'll need to get a starter BIN over at Code59.

I would skip the 50lb injectors - there seems to be issues with them. The 60lb Siemens/Mototrons are the way to go - you don't have to mod the ECM, they're very linear, and have great resolution.

Also, I'd read Josh's info at PowerTunePlus.... http://powertuneplus.com/
It will give you some hints on what to look for on the logs, and it's a great piece to read just as a refresher.

I'm helping another member get his 60lb tune dialed in right now - I'll be posting it over at Code59 before too long. It would be a great starter for you, if your build is about the same.

PM me if you need to discuss more. We can email/phone too.
 

2500avalanche

Well-known member
Re: switching from Ultimate to code59?

Rob,
Thanks. IT seems like when you do one thing to these, you open up a can of worms... But in a good way.
I will read these this weekend, and see if I have any more questions. So, 60# are the way to go. Thanks!
 

dgoodhue

BuSTeD 4.3
Re: switching from Ultimate to code59?

I would recommend being very methodical on tuning.

I used the 60# starter bin. My first series of tunes, I ended up scrapping and starting over after a few days, I didn't have the autotune setup properly and my tune had lots high rpm lean spots. I used a different FP, played around with the injector constant (egr pulsewidth).

My second go around, I used the 60# bin, set the FP to 43# and didn't have to play with the injector constant. My Sy was very drivable with this combo. My VE table has changed quite a bit since then, but I could at least drive my Syclone around.

Anyways once you get your idle down, go for targeted drives. You want to do the vacuum area (0-100kpa) before doing part throttle boost, then work on WOT last. The rpm cells are every 400rpm, so try to drive at 1200, 1600, 2000, 2400 for period of time and through different loads (up hill/down hill). You wan tot do it at steady throttle position so you not introduction Acceleration or Deceleration Enrichment. Start off with 1st gear, AC on AC off, then 2nd, etc.

My last round of tuning, I decided to loosen my wastegate (so it also leaking to create lag) on my turbo to get to the 0-10" vacuum, I was find my turbo was affect my ability (ie accelerating) to tune those transisition area's. My value in those area were lean.
 

vinnieTy

TY # 1889
Re: switching from Ultimate to code59?

OK,
I am new into this, but after talking to Brandon (Aeroking), I finally am starting to understand about this subject.
I am wanting to go faster (of course) after my rebuild. I would like to put on bigger injectors (50#), and get a larger turbo. The ultimate I have does not support this.
So, I would need to go code59, or basically get a chip programmed for the truck. To do this, I am going to need to purchase and Ostrich 2.0, correct? Or what other/styles are out there to help someone do a chip burning. Is this difficult to do? Any help/thoughts would be great as I am new into this area, but want to get the most from my truck (before the rebuild, I loved it, but thought it was not all it could be...)
Thanks guys

2500avalanche - i dont mean to change subject but i am in the process of reading all about the chips myself and trying to just like you learn more about them. ANyway the reason im posting is becasue if you do decide to get rid of the ultimate i would be interested in it, so if you can keep me in mind first when you do decide to get rid of it i would appreciate it.

thanks
 

2500avalanche

Well-known member
Re: switching from Ultimate to code59?

will do
2500avalanche - i dont mean to change subject but i am in the process of reading all about the chips myself and trying to just like you learn more about them. ANyway the reason im posting is becasue if you do decide to get rid of the ultimate i would be interested in it, so if you can keep me in mind first when you do decide to get rid of it i would appreciate it.

thanks
 
Top