Syclone Restoration

BigBadSmoosh

Picking fights on I-65 since 2013
Re: Syclone Restoration

Jersey 91/93 said:
When am I coming over to work on this thing again? You still have beer at your place, right?

I pretty much work on it every weekend, let me know when you are free, lots of stuff to do :tup:
 

George Blake

DONATING MEMBER
Re: Syclone Restoration

Heating bolts. Use MAP gas. Gets pretty hot but not as hot as acetalin (?sp).

Once you heat the bolt, it expands. This pushes the threaded hole open as well. Hit the bolt with synthetic oil. Rapidly cools the bolt AND it wicks into the now vacant area between the bolt and the threaded hole. Back the bolt out immediately.

Win my trans at Nats. Stock + build. Everything stock except input drum, sprag, reaction shaft, and servo lineup. It will have a 2300- 2500 stall converter in it with lockup. Pan is a Derale. The case will be hit with reclaim and then textured with glass bead. Then I spray it with a ceramic coating and bake it in my buddy's oven he made. Very worthy of a resto project. Will include a NOS TV cable for nostalgia purposes.

Ken (warmpancakes) may have a complete stainless fastener list. He also knows a good company to use to get them.
 

BigBadSmoosh

Picking fights on I-65 since 2013
Re: Syclone Restoration

George Blake said:
Heating bolts. Use MAP gas. Gets pretty hot but not as hot as acetalin (?sp).

Once you heat the bolt, it expands. This pushes the threaded hole open as well. Hit the bolt with synthetic oil. Rapidly cools the bolt AND it wicks into the now vacant area between the bolt and the threaded hole. Back the bolt out immediately.

Win my trans at Nats. Stock + build. Everything stock except input drum, sprag, reaction shaft, and servo lineup. It will have a 2300- 2500 stall converter in it with lockup. Pan is a Derale. The case will be hit with reclaim and then textured with glass bead. Then I spray it with a ceramic coating and bake it in my buddy's oven he made. Very worthy of a resto project. Will include a NOS TV cable for nostalgia purposes.

Ken (warmpancakes) may have a complete stainless fastener list. He also knows a good company to use to get them.

thank you for the advice..

I spoke with ken a bit about the stainless hardware, I still need to figure out exactly what to order so I get all of the right stuff..

I was going to pm you on a few tranny options/questions..
 

BigBadSmoosh

Picking fights on I-65 since 2013
Re: Syclone Restoration

Here is a pic of the truck when it was close to being a whole truck.. this is from the last time it was running.. around 2 years ago

syclone.jpg
 
Last edited:

BigBadSmoosh

Picking fights on I-65 since 2013
Re: Syclone Restoration

so this weekend I had some time to play around with the frame on saturday and the engine on sunday (it rained)

took off the steering box and went through some of the wires.. unfortunately it looks like i have some soldering to do..

Wires

-Main harness a few wires are cut with copper showing
-one wire is cut and the copper is showing signs of corrosion
-I'll probably just splice out the bad parts and solder in good parts, that is unless anyone has any suggestions as to how to improve this repair?


Steering box
-Going zq8 with a renz shaft, as soon as I can find one at an affordable price

Engine
-Tore apart the top end, cylinders look ok..
-lower intake is gross.. needs a through cleaning
-Need to decide what to do with the motor.. suggestions?

Pics
dsidepistons.jpg

lowerintake.jpg

topend.jpg
 

BigBadSmoosh

Picking fights on I-65 since 2013
Re: Syclone Restoration

yeah i was really surprised.. the only real wear I can see is where the rods were rubbing against the cam.. you can see it in the last pic.. I haven't opened up the oil pan yet, but i know if I do decide to put it back together stock, i'll probably at the least replace the oil pump.
 

BBW808

New member
Re: Syclone Restoration

We all know the weakness in our motors is the rods and pistons. I would do the lower end at a minimum because its already out, and after you spend all the time restoring everything else, the last thing you want to do is have to rip out the motor again. IMHO.
 

BigBadSmoosh

Picking fights on I-65 since 2013
Re: Syclone Restoration

BBW808 said:
We all know the weakness in our motors is the rods and pistons. I would do the lower end at a minimum because its already out, and after you spend all the time restoring everything else, the last thing you want to do is have to rip out the motor again. IMHO.

I keep hearing that.. I was talking about the connecting rods, btw..

as for taking apart the bottom end, I've never done it.. which is why i'm hesitant.. There are two builders i'd consider handing over my motor too.. when winter rolls around i'll probably drop it off at one of them if I can afford it.
 

DynaGlide

Ton-Eighty
Re: Syclone Restoration

If that's what is considered dirty, I wish I'd kept pictures of my engine when I tore it apart. Someone who had the truck before me didn't think that changing the oil regularly was important.
 

BigBadSmoosh

Picking fights on I-65 since 2013
Re: Syclone Restoration

oh yeah, no major progress this weekend.. and the upcoming weekend i'll be on a mini vacation..

I'm thinking i'll need to find a replacement stock turbo or figure out how the hell to get the bolt out of the exhaust housing of mine..
 

BigBadSmoosh

Picking fights on I-65 since 2013
Re: Syclone Restoration

Jersey 91/93 said:
You did get a distributer and ECM out of your garage temporarily!

distrib, ecm, distrib coil, ignition module.. good luck with them :tup:
 

Aeroking

e.i.
Re: Syclone Restoration

ok, my truck is sitting right now with no front clip (fenders, core supp., bumpers, etc) the motor is stripped to the block/heads. I am gonna be pulling it this weekend.

Do i need to drop the front diff, or lift the cab??

should i unbolt the tranny from the engine, and pull them out seperate, or can i pull them out as an assembly??

the truck is about 2 feet up on jack stands, so dropping the trans seperate, shouldnt be hard, I'd just like to pull both together... if i can.

oh... what are good hoist points for lifting it out??
 

BigBadSmoosh

Picking fights on I-65 since 2013
Re: Syclone Restoration

Aeroking said:
ok, my truck is sitting right now with no front clip (fenders, core supp., bumpers, etc) the motor is stripped to the block/heads. I am gonna be pulling it this weekend.

Do i need to drop the front diff, or lift the cab??

should i unbolt the tranny from the engine, and pull them out seperate, or can i pull them out as an assembly??

the truck is about 2 feet up on jack stands, so dropping the trans seperate, shouldnt be hard, I'd just like to pull both together... if i can.

oh... what are good hoist points for lifting it out??

I had to drop the tranny from the engine because I could not lift up the cab due to seized bolts.. it wasn't that hard because I had done it before..

becareful with the angle of the engine it can hit the firewall and cut wires/break the AC box..

IF you can lift up the cab in the front a bit, enough for the oil pan to clear the front diff you can pull the engine/tranny together.. if not seperate them.
 

BigBadSmoosh

Picking fights on I-65 since 2013
Re: Syclone Restoration

oh yeah, as for an update.. i've por-15'd the front and rear of the frame.. i'm hoping to weld the nuts for the engine mounts in sooner than later along with the shock tower supports renz is working on.

I have to fix a few old wires and attempt to clean stuff up, I simply haven't had $ to buy all the new parts to replace the old ones.
 

BigBadSmoosh

Picking fights on I-65 since 2013
Re: Syclone Restoration

Raist103 said:
thats what i am waiting for, pics

it has two coats of regular por-15.. I have to paint the visable spots with the shiney black paint before i take pics..

i'll try to take a few tonight or this weekend.
 
Top