timing question

when i disconnect the tan wire and set the timming it runs and idles good but when i reconnect the tan wire it starts running terrible. again. ive reset the comuter after i set the timming i just dont understand why.
 

bezerk

New member
Re: timing question

your stock balancer might be off, so your 0 timing isn't 0.
stock balancer aren't that great
 
Re: timing question

Well i give up on this truck i spend everyweekend for the last two years just trying to get it to just idle and run right my wife says sell it..
ive done everything possible to make it run good..even changed out engines.
so if anybody wants it let me know..i just cannt get it to idle.
it only has 67,000 miles on it.
 

jwaller

Evil Genius/SyTy Guru
Re: timing question

try removing the MSD. there have been more problems related to their products than I can remember. with your build you dont need it. try it without it.
 

QUICK STORM

B.A.M.F. BMW Tech
Re: timing question

you may want to find true tdc with a piston stop tool. i believe your stock balancer has slipped
 
Re: timing question

checked balancer with another one i have there the same.

when i try to time it its way off i dont even see the line on the balancer if i put it to where it lines up it dies and has a Very hard to start and runs VERY bad. im at my end with this truck.
 

Don W.

Stab it and steer it
Re: timing question

My balancer has 2, yes two, lines on it. 'bout drove me nuts when I was checking TDC. Make sure you're looking at the correct one. Assuming you have 2 to start with of course.
 
Re: timing question

when i try to time it i adjust the dist to where the engine runs and then turn on the timing light and no marks showing and if i advance it to one mark it just kills the engine then when i retard it to the other mark it just kills it again.
 

Don W.

Stab it and steer it
Re: timing question

:rant: Maybe I'm showing my ignorance but how do you check one dampener against another when one is still on the truck? Or did you pull one? In my experience with a dampener in hand the key-way lines up with the mark. Not sure if that's the case with our trucks. From what I read your timing off. With the MSD you're getting multiple sparks at idle. Never had a 6a so curious if that's disabled when setting timing or what.:rant:

Has this motor been apart? Wonder if the cam is timed correctly.
 
Re: timing question

really my question is when i start my truck with the tan wire disconnected it runs great until i reconnect the wire then it runs terrible.
 

bezerk

New member
Re: timing question

92Typhoon1679 said:
really my question is when i start my truck with the tan wire disconnected it runs great until i reconnect the wire then it runs terrible.

timing?
 

bezerk

New member
Re: timing question

it happened after you did something, or did it started to do this out of the blue?
might be helpfull if you tell us why it went bad.
 

SBNova

New member
Re: timing question

Get a piston stop and find true top dead center. Dont go by the fact that your two balancers seem to line up. My balancer is wrong. I just went through the same thing. When my timing was too far advanced (by lining up to a faulty mark) it would run OK with the tan disconnected. When I reconnected the tan wire, the ECM would apply advance and the engine would run worse.Too much advance + even more advance = poor running engine. Mine wouldnt idle either. Your timing is wrong, I would bet on it. You could also have distributor pick up or module problems. Check those too, or just replace them.
 

LandryPoole

New member
Re: timing question

Have you ever had the Distributor out? Just wondering if it is a tooth off? Also, make sure the Dis cap is seated properly. The are easy to install and not get it seated right. I agree with timing from using piston TDC. It is easy to do, and would allow you to make a new mark on your ballancer as well. Otherwise, why not try this. Start up your truck, time it as you normally would, and then back the timing down just a touch, reconnect the tan wire, and then see how it runs. If it runs good, then you know that it is more than likely the ballancer has slipped. Good luck.
 
Re: timing question

replaced the distributor today with another one i had on my spare typhoon engine well i set the timing to 0 it ran a little rough so i retarded it about 8 degrees and it idled good. then i reconnected the tan wire and that seemed to fix be the problem i dont know why i did change the ignition module on the other distributor. so its at least running with the tan wire connected and i can see the timming mark. im going to buy a new balancer sooner or later its a money thing. right now i just need it to run.

but it still hunts at idle somewhat though
i did notice that my shaft on the throttle body is loose and makes a clanking noise when i move it so i might have a vacume leak right there causing the hunting.
 
Re: timing question

all this started after i replaced the intake gaskets this weekend trying to find out why its hunting so bad. i thought maybe i had a leak on the intake gaskets.
when i replaced them i went exactly by the book.

and when i restabed the distributor thats when all this started.
 

Don W.

Stab it and steer it
Re: timing question

I'm almost afraid to start my own "it won't idle" thread.:rotf: No hijack, if it gets worse I'll wait awhile and then post.:D
 
Top