Tuner pro help

twin74s

Member
OK, my ty in the morning you have to give it gas and bring it to like 2k rpm for about ten seconds on start up. If you dont it goes pig rich coughs, and shudders until it cleans out. It only does this in weather below bout 55. Where in tuner pro do i change the cold start correction i just cant seem to figure it out. Thanks Ahead of time David
 

JSM

Active member
Re: Tuner pro help

I don't have tunerpro in front of me, but it is a cold start AFR table. You will want to look at the values below 55 deg. (might be in Celcius)
 

TYTILIDIE

METH HEAD
Re: Tuner pro help

Try Cold engine AFR vs. Coolant Temp and MAP (F56). Its in tables and functions down in the cold start area.
 

twin74s

Member
Re: Tuner pro help

Ok i tried it will have to wait til this evening to see if it works. Also do none of the maps go above 4800 rpm?
 

twin74s

Member
Re: Tuner pro help

And one more thing is there anyway to turn the graphs so the can be easier to work with?
 

TYTILIDIE

METH HEAD
Re: Tuner pro help

twin74s said:
Ok i tried it will have to wait til this evening to see if it works. Also do none of the maps go above 4800 rpm?

Are you working in Code 59 or 58? I cant remeber a lot about 58tables but I know that in 59 the F29x goes up to 6400 RPM. Im sure you can add the spots you need as well. I vaguely remember someoen asking about this at one point in time or another. Ild like to add more points to the F31M table.
 

TYTILIDIE

METH HEAD
Re: Tuner pro help

twin74s said:
And one more thing is there anyway to turn the graphs so the can be easier to work with?

Yes, you open your graph, put the pointer over the graph and hold the control button.
 

twin74s

Member
Re: Tuner pro help

TYTILIDIE said:
Are you working in Code 59 or 58? I cant remeber a lot about 58tables but I know that in 59 the F29x goes up to 6400 RPM. Im sure you can add the spots you need as well. I vaguely remember someoen asking about this at one point in time or another. Ild like to add more points to the F31M table.

IM not really sure i bought it with the software and stuff... How would i know which im am in?
 

twin74s

Member
Re: Tuner pro help

TYTILIDIE said:
Yes, you open your graph, put the pointer over the graph and hold the control button.
WOW thank you so much. It was very frustrating to not be able to see the graph as it was going the wrong way. Thanks
 

JSM

Active member
Re: Tuner pro help

TYTILIDIE said:
Are you working in Code 59 or 58? I cant remeber a lot about 58tables but I know that in 59 the F29x goes up to 6400 RPM. Im sure you can add the spots you need as well. I vaguely remember someoen asking about this at one point in time or another. Ild like to add more points to the F31M table.

You can't just add more points to tables or extend them. That is all in the code work.

Code58 is stock based calibrations,

Code59 is where the code and math behind it has been changed, tables extended and many other features. www.code59.org as posted is where to find more info.
 

TYTILIDIE

METH HEAD
Re: Tuner pro help

JS Manufacturing said:
You can't just add more points to tables or extend them. That is all in the code work.

Code58 is stock based calibrations,

Code59 is where the code and math behind it has been changed, tables extended and many other features. www.code59.org as posted is where to find more info.

Well that blows. I went into the XDF edit and added 8 more spots to F31M and re did the lines. So I guess it wont work? Oh well.
 

skwayb

NWSTP
Re: Tuner pro help

twin74s said:
Ok i tried it will have to wait til this evening to see if it works. Also do none of the maps go above 4800 rpm?

In Stock 58 code, F29 only goes to 4800 and up to 0 PSI. For RPMS over 4800 the F30 table takes care of that. It is an adder table. Basically your VE is F29+F30 . The F30 table goes up to 6400 RPM. So the last cell in F29 you are in it adds the F30 VE to when you are over 4800 RPMs

When you get into Boost the F77 table is a multiper to handle the fueling for over 0 PSI. It is all part of the fueling equation.

BPW = BPC * MAP * T * A/F * VE * F33C * BLM * DFCO * DE * CLT * F77

or

BPW = F28 * MAP * T * A/F * (F30+F29) * F33C * BLM * DFCO * DE * CLT * F77

I would read the P4 document on www.nwstp.com and go over the fueling chapter to understand it all. http://www.nwstp.com/chips/P4_docs/Turbo_P4_Doc.pdf

Most of what is in that document applies to 59 also. Dig just added bigger VE tables, WBo2 Fueling control, expanded F77 table, 3 Bar Support and a bunch of other nice features with more to come.
 

skwayb

NWSTP
Re: Tuner pro help

TYTILIDIE said:
Well that blows. I went into the XDF edit and added 8 more spots to F31M and re did the lines. So I guess it wont work? Oh well.

Nope, you will be reading data from other tables and changes to that will mess up the other table.
After looking at it, by adding 8 lines you are making changes to the F33 and F34 tables.

F31M ends here...........
The 8 lines after the end of the F31M table are
Code:
                       1922 ; Table : Voltage Compensation vs. Battery Voltage
84e2 8b                1923 F33             db      $8B     ;  4.8 V ($84E2)
84e3 89                1924                 db      $89     ;  6.4 V ($84E3)
84e4 86                1925                 db      $86     ;  8.0 V ($84E4)
84e5 83                1926                 db      $83     ;  9.6 V ($84E5)
84e6 80                1927                 db      $80     ; 11.2 V ($84E6)
                       1928 
                       1929 ; Table : DE Coolant Factor vs. Coolant Temp
84e7 00                1930 F34             db      $00     ;  -28 degC ($84E7)
84e8 00                1931                 db      $00     ;  -16 degC ($84E8)
84e9 10                1932                 db      $10     ;  -4  degC ($84E9)

So you would be over writting values in the F33 and part of the F34 tables.
 
Top