Tuning alky on 2bar technology?

Flyin Ryan

hated cuz he drives fords
Yeah I know it's kind of defeating the purpose of running a alky or meth kit if your not gonna turn up the boost but honestly it's a daily driver that's destroyed three propshafts already and i'd only be running high levels during the weekend street sessions anyways.

Currently I run 18 psi on 93 octane and depending on how much the EGR heat soaks the ic I get 0 -3kr tops. I wouldn't be looking for anything higher except maybe 20 psi on very rare occasions.

So what im asking is on a pretty much stock truck.. how can you run/tune alky without being pig rich?

Some one mentoned that you could run 2bar to the ecm but 3bar to the alky control box.. any idea how to do this? or what it involves?

Thanks in advance
 

JSM

Active member
Re: Tuning alky on 2bar technology?

The alky has it's own map sensor.

The problem is with 2 bar, your truck ecm only sees 14.7 psi. After that level the computer can't compensate for the additional boost/airflow. So it delivers fuel for 14.7psi, not 18 or 20.

Why NOT go to 3bar. Then you can dial in the fuel table properly. With alky you will need to pull fuel away, which is going to be tricky with only 2 bar.
 

sytyguy

Moderated User
Re: Tuning alky on 2bar technology?

I agree with Jeff.....go 3 bar and do it right, but if you have your heart set on not going 3 bar and you're using a system w/o a map included, you could do the following:

It would be possible to wire up a 2 bar map to the ECM, share the vac source and run one pin from a 3 bar map (the green wire IIRC) for the progressive controller on the alky system. Really, that's all the alky needs....is that one wire, so essentially, your only tapping into the factory vacuum line and (possibly) a couple of wires. You need to wire 5v and a ground, but that could be done w/o tapping into the factory harness (although it would be easier to tap in). Then just output the pin that would normally go to the green wire to the alky controller.

So, you'd need:

- Alky system (duh)
- 3 bar MAP sensor (mounted elsewhere)
- 7/32" vacuum line tee
- Several inches/feet of 7/32" vacuum line
- GM MAP sensor pigtail (PICO #5613PT = $6.99)

Then:

- Mount the MAP sensor
- Tee into the vacuum line going to the 2 bar MAP sensor
- Route vaccum line to 3 bar MAP sensor
- Tap into the 5v and Ground wire going to the 2 bar MAP sensor
- Wire them into the corresponding wires on the new MAP pigtail.
- Run the leftover wire from the pigtail to the alky controller.

I haven't done this myself, but it seems to work in my head (but so does cold fusion, world peace, sex with Ashley Judd, etc....). The easier, proper alternative? Get a stockish 3 bar bin (T1-18 for example) onto your chip and just use one MAP sensor, the 3 bar one.

Hood
 

Flyin Ryan

hated cuz he drives fords
Re: Tuning alky on 2bar technology?

well I don't have my heart set on anything except trying out the alky kit so I was just fishing around to see what is possible and what's not. Some people say it's possible to run alky with a 2bar, some say no, some say yes but with tons of tuning.. I just wanted to hear more opinions and some opinions on this duel map setup.

I gathered it would be the easiest route and possibly the most effiecent to simply go with a 3bar bin so i'll ask around for such

Thanks for the quick replys guys
 

Jer

Don't taze me bro!
Re: Tuning alky on 2bar technology?

Really wouldn't be tons of tuning because you're limited to 14.7psi due to the 2bar. The key is that using alky injection allows you to run considerably higher boost with NO other mods. So to do this mod w/o doing the 3-bar would be kind of wasting your money. Like putting race gas in w/o advancing timing or raising the boost... what's the point?
 
Top