tuning issue

gringo76

New member
got some sort of electrical issue I think causing rough idle. thought someone might be able to give me some clues to check.
truck will drive for few miles and idle at 15.8 to 1 and idle like new and then outta no were 17 to 1 and truck running rough as it is lean and do that for little while and then back to normal. datamaster shows nothing going outta wack when this occurs. mods on fuel related stuff are turbo tweak chip, 42 lb injectors, 255 pump, 3 bar map, pretty normal stuff and all new. anyways truck runs good driving just a idle issue. I don't have another ecm to try so not sure on that. thanks for any input
 

gringo76

New member
Re: tuning issue

just was watching dm and finally seen something change when idle goes to crap. open loop is good and soon as it goes to closed loop o2 mv drop and runs lean like 17 to 1. as it sometimes switches back to open loop idle comes back to good. thoughts?
 

gringo76

New member
Re: tuning issue

I did flip the #2 switch on turbo tweak chip to keep idle in open loop and it fixed idle but as you hold rpm up to say 2000 and it goes back to closed it leans out again and o2mv dive low again. while driving with throttle just cracked it is running lean, get into it just a little and all good. seems to be just a idle to just off idle lean condition, #2 switch did fix the idle issue. any thought guys?
 

gringo76

New member
Re: tuning issue

that what I was thinking but I figure I see what the pros would say before I started throwing parts at it
 

Don W.

Stab it and steer it
Re: tuning issue

You can try turning #3 on but with narrow band only 1,3,4 should be off.

You could also try turning up WOT a click or two.

Can you post a log?

Already mentioned, maybe the o2 died.
 

gringo76

New member
Re: tuning issue

I will post a log tonight when I get home, I was thinking maybe turning the idle up a few clicks on the chip it self since its blended into tune and issue seems to only be at idle to right off idle. its a pretty new o2 but that don't mean anything so might put one in for piece of mind. is there a certain part number o2 I should get that works better for these?
 

Eric Sy GN

Donating Member
Re: tuning issue

I agree the O2 may have died. It would be good to know what the BLM at idle looks like. That would tell us if the computer is trying to add or subtract fuel.
 

gringo76

New member
Re: tuning issue

with #2 swithed off the Lterm and Sterm are in red, both at 118 and blm enabled. with the #2 switched on and open loop blm off and Lterm in red at 120 and Sterm not in red at 128, trying to figure out how to post a log
 

gringo76

New member
Re: tuning issue

all right I replaced the o2 sensor and at same time put a new rpm 58 mm throttle body on it. I put throttle body on it because the original 90k throttle body shaft or bushings were wore out and giving diff readings from time to time. new o2 seemed to fix my lean condition at idle in closed loop although I have not driven it and got it good and hot yet. with new rpm 58mm tb I cant get IAC pos below 66. it seems to run great and idles about 825-850 rpm at about 14.5-1 af, tps% at 0.41 and tps at .45 volts. I changed two diff IAC motors and nothing changes,i have also played with idle screw and can only get IAC to go up not down . like I said seems to rum and idle good, should I be concerned with IAC pos with new tb or is that normal with bigger tb?
 

gringo76

New member
Re: tuning issue

on the IAC motor position with its at 140 does that mean plunger is all the way out and closes the air path to idle up car and lower number opening plunger letting air threw to raise idle rpm? just making sure I am thinking correctly. thanks
 

Eric Sy GN

Donating Member
Re: tuning issue

The lower the IAC number, the more closed the pintle is, closing off the air. If the IAC was 0, that would theoretically be closed. If you want to lower the IAC number, you would need to open the throttle blade by turning the screw clockwise.

Make sure you check the IAC number with the truck fully warmed up, in park. We are usually looking for around 20-30. However, as long as its running ok and you are happy with it, you could leave it alone.

Eric
 

gringo76

New member
Re: tuning issue

ya I tried turning is clockwise but then the idle starts to increase before the iac pos goes down. when it had stock tb on it that would work but does not seem to with new throttle body, like you said if truck is running good and good af what the hell. I will get it out and drive tomorrow and report back. thanks for your help.
oh ya I am slowly gathering parts for 96 up vortec head swap and cam, will I need to get whole new chip from you guys or just work with one I got?
 
Top