Ultimate, alky, & tune RANT

Don W.

Stab it and steer it
:rant: Doing what I thought would be a good idea I installed alky in my truck this winter. All along I thought alky and an Ultimate were good to go. Now I'm told (by Julio Don) they're not. "Get a chip from Nolan" he says. Which I'm willing to do, I have Nolan's phone.

One of the deciding factors was TookyCat’s long post back in ‘03

http://www.syty.net/forums/showthread.php?t=14608&highlight=ultimate+alky+tune

So anyway I’m just pissed and would welcome input before calling and spending more $$ on this tune.:rant:

FYI The “problem”, briefly, is that during 3 runs at Infineon Wed. (rain-out) I experienced noticeable miss at high RPM’s. Meaning just before each shift and at the far end. Engine is not over revving. The miss goes away if I turn down the "pump gain control" almost to off which, to me, is not correct. Was gonna turn down the FP when we got rained out. Can supply Datamaster if interested.

Thanks, all comments appreciated, now that I'm calmed down a little.
 

JSM

Active member
Re: Ultimate, alky, & tune RANT

I have run the t324 setting on pump and alky without issue. If you have a miss what is the gaps on yoru plugs, what plugs, what ignition, etc.

I have found with not enough timing it won't work.
 

Don W.

Stab it and steer it
Re: Ultimate, alky, & tune RANT

JS Manufacturing said:
I have run the t324 setting on pump and alky without issue. If you have a miss what is the gaps on yoru plugs, what plugs, what ignition, etc.

I have found with not enough timing it won't work.

6 month old NGK UR5's gap .035, "0" timing, stock dist, new NAPA cap and rotor "good stuff", new Taylor wires. Stock turbo, down pipe, cat and muffler. See sig for rest. FP -was- set to 40 with vac line connected. Now it's at 35 but have not driven the truck at that setting. In normal driving the truck runs great. Difficult to do test runs to 100 "off track" so may have to wait, might be two weeks because weather is not looking good for next week either.
 

Jimmy

Banned
Re: Ultimate, alky, & tune RANT

Yeah I bet you need to gap the plugs down,to like .028 or so.The alky loves tight gaps.
 

TurboJunk

questionable
Re: Ultimate, alky, & tune RANT

i had problem very similar with my ty, the wires were messed up the boots were burnt from the headers. no alky but at high boost it had a horrible miss, also my rotor (which was brand new took a shit)
 

Don W.

Stab it and steer it
Re: Ultimate, alky, & tune RANT

OK gap the plugs to .028, that I can handle. I can inspect the wires and look at the cap and rotor.

Is there a FP I can use as a starting point? Inj's are 33# Lucas replacements.

Thanks all!!
 

sy#2921

BAMF
Re: Ultimate, alky, & tune RANT

i wouldnt go to .028 to start try some where inbetween the two since you want to run just below the largest gap possible. I know it might be a pain to do but with stock manifolds its not bad to take out the plugs. try .031ish first then if that doesnt work go to .028. I know i have a bigger turbo and 50#'ers but i run my ur6's at .032 with my meth kit and it works great.
 

93 TY 2185

Donating Member
Re: Ultimate, alky, & tune RANT

I had similar problems that you are having above 15psi.
I gapped my plugs down to .028 now above 15psi it’s running great see Sig.
I've found for WOT the right fuel pressure needs to be lean.
A good starting point would be 40 PSI.
This is with the stock injectors and a Ultimate setting of your choice. Alky knob set at 10 O'clock with a factory settings left untouched.
I’m using a Wbo2 and I would suggest you do the same if you want good results.


HTH
 

JSM

Active member
Re: Ultimate, alky, & tune RANT

93 TY 2185 said:
I had similar problems that you are having above 15psi.
I gapped my plugs down to .028 now above 15psi it’s running great see Sig.
I've found for WOT the right fuel pressure needs to be lean.
A good starting point would be 40 PSI.
This is with the stock injectors and a Ultimate setting of your choice. Alky knob set at 10 O'clock with a factory settings left untouched.
I’m using a Wbo2 and I would suggest you do the same if you want good results.


HTH

Wade is right on track with what I have found. Sometimes we even go tighter but at much higher boost also.

FP should always be adjusted with vacuum line off.
 

Maxtor

New member
Re: Ultimate, alky, & tune RANT

Jimmy said:
Yeah I bet you need to gap the plugs down,to like .028 or so.The alky loves tight gaps.

Do what Jimmy and the others have suggested and close up your plug gap. On one of my past trucks I had this issue at 0.032", went down to 0.028" and never had another problem. I ended up running alky on both of my stock Sy's and had good results at 0.028" on both of them.

Every truck is different, but with the Ultimate I always ran around 50psi FP. Two thought processes for tuning with alky - you can either tune for it to be there (IE - take out fuel under boost to achieve optimal AFR) or you can tune without the alky, then turn it on for the MAT reduction knowing you will run rich under boost. The benefit to the first way is better performance (theoretically), the benefit to the second way is you don't detonate the crap out of your motor if the alky quits spraying and you run lean. A lot of people compromise and find a happy medium. If you want to tune for alky, you shouldn't use fuel pressure since you are only spraying while under boost. The best way is to target the F77 (if memory still serves) boost multiplier table. Unless you have a WBO2 I would be very cautious about pulling out fuel to tune for the alky.
 

Six-is-Enough

Use to do a little Boost
Re: Ultimate, alky, & tune RANT

Jeff S. got you before I did, but I run my plugs gapped @ .028. When I first put the alky(razor kit) on my truck had similar problem on the lower timing settings. Lower the gap and give more timing. good luck.
 

It's just a six

Super Member
Re: Ultimate, alky, & tune RANT

Do you run an MSD box ,or are you running stock set-up for ignition??
I run the 1S Aquamist...I do not seem to have a miss... but I think you guys must be pumping more alky than I am?? :tup:
 

Don W.

Stab it and steer it
Re: Ultimate, alky, & tune RANT

Thanks everyone!! Will close the gap to, I'm thinking, .030 this weekend. If the weather holds I have spot to test but if I go to 100 I run out of road but should be able to tell something. Obviously very early in the tuneing and drag season so time I got. Really appreciate all the help.:tup:
 

Don W.

Stab it and steer it
Re: Ultimate, alky, & tune RANT

It's just a six said:
Do you run an MSD box ,or are you running stock set-up for ignition??
I run the 1S Aquamist...I do not seem to have a miss... but I think you guys must be pumping more alky than I am?? :tup:

Stock dist, timing @ "0". Even with the problems I do have some knock. Prior to alky the truck seemed to like a 2 or 3 degree retard. But one thing at a time. I'd like to leave the timing in if I can.
 

Turbo6

10.20@131.8
Re: Ultimate, alky, & tune RANT

You do not want to run as big a gap as possible. You want to run the gap that gives the most power. I run a .024 gap. I have seen cars pick up power on the dyno closing in the gap as low as .020 on V8 and V6 blown applications.
 

gjp

another post whore
Re: Ultimate, alky, & tune RANT

How was the turnout of wednesday??? I wanted to go with alky too. I have to learn my truck as is first before I mess with that. I know you will figure it out Don. Good luck.
 

Don W.

Stab it and steer it
Re: Ultimate, alky, & tune RANT

gjp said:
How was the turnout of wednesday??? I wanted to go with alky too. I have to learn my truck as is first before I mess with that. I know you will figure it out Don. Good luck.

Jeremy and I were there. Maybe 150 cars total. It was COLD. Got rained out after 3 timed runs. Weather looks bad for next Wed also. I'm gonna play it by ear but may wait for the the weather to warm up a bit once this darn rain stops. As you know we're having really strange weather around here lately, snow level down to almost sea level.:tdown:
 

Don W.

Stab it and steer it
Re: Ultimate, alky, & tune RANT

Syclone#2960 said:
If you are using heet...be sure to use the yellow bottles and not the red.

Right now denatured from the hardware store but will be looking for the the real thing soon. Some folks seem to do well on denatured though. I knew 'bout the heet thing, thanks.
 
Top