Ultimate problems

Raist103

Engine Killer, iPhone Killer, Lawnmower Killer
Just put the chip in and on T15 or val (well any mode i tired others just not at WOT) mode very bad missing as soon as you step on the gas and once you get the Ty moving if you have a little throttle or full out it is missing bad plus only 2-5 psi boost. Anyone have this problem before? Could the stock chip be in backwards or some thing stupid like that.

By the way I did end up going to a advanced auto store and picked up a 3 map bar and if anything it just made it worst, could just be me though.

I changed my plugs, checked my wires and found one burnt on the dp and change that to a ATR wire, that is all I had extra laying around. (the rest are Talyor) and no differance, plugs were a little blk but not to bad and rest of the wires look good. checked Conrad cap and loooked good but tried a extra Accel cap I had laying around and again no diff.

Any help would be great thanks
 

syntax

Member
was it running perfectly right before you put the chip in? take it back out and see if all your problems go away, if they do, then you know for sure its the chip, usually ultimates require 7psi more fuel pressure over a stock chip, do you have a afpr? make sure both chips are seated correctly, also, your symtoms sound like exactly what happens when you try to run a ultimate and a 2bar map sensor, make sure the parts store gave you the correct one, or maybe try to borrow a gm 3bar map from a friend, can anyone jump in with the part number for the real 3bar sensor? good luck
 

ed hess

race or get outta the way
don
which version of the ultimate did you tell em you wanted when you ordered?
I order mine for the stock turbo with stock injectors.
I cant beleive you put the chip in and didnt do the 3 bar sensor at the same time.
So you didnt follow the directions!
Is your down pipe still not connected to the exhaust?
Did you get datamaster so that you can REALLY tell what is going on?

I will be installing my chip in a couple weeks. (waiting for it to ship)

I would suggest you put back the old chip, the old 2 bar sensor and start over.
Get it running properly with the datamaster 1st.
Then follow the directions explicitly!!!!!!!!!!!!!!!
Anything else is just creating frustration.

ed

btw was that you that drove buy yesterday or was that mad mike?
or yeah was that youalso on evesham rd the other day in the GN?
 

smeagol

Active member
Gotta make sure you have the stock chip piggybacked to the Ultimate setup.

Probably need to trim the retaining clips on the ECM as well (white tabs on either side of the plug in the ECM).

A 2 BAR MAP SENSOR WILL NOT WORK WITH AN ULTIMATE CHIP. YOU MUST USE A 3 BAR MAP SENSOR.

A 2 BAR MAP SENSOR WILL NOT WORK WITH AN ULTIMATE CHIP. YOU MUST USE A 3 BAR MAP SENSOR.

A 2 BAR MAP SENSOR WILL NOT WORK WITH AN ULTIMATE CHIP. YOU MUST USE A 3 BAR MAP SENSOR.

A 2 BAR MAP SENSOR WILL NOT WORK WITH AN ULTIMATE CHIP. YOU MUST USE A 3 BAR MAP SENSOR.
 

Raist103

Engine Killer, iPhone Killer, Lawnmower Killer
1. btw was that you that drove buy yesterday or was that mad mike?
or yeah was that youalso on evesham rd the other day in the GN?

2. I cant beleive you put the chip in and didnt do the 3 bar sensor at the same time.

3. Did you get datamaster so that you can REALLY tell what is going on?

4. So you didnt follow the directions!

5. which version of the ultimate did you tell em you wanted when you ordered?

6. Is your down pipe still not connected to the exhaust?

1. That was me in the GN.
2. I was on my way to pick up the 3 map bar, they had to order it.
3. No cash to get the cable yet. (This was part of a trade for my turbo and dp)
4. He did not give the directions with it and I did look in the sytyauthority. but it does not show what dir. the stock chip is to go in and followed those directions.
5. I was told it was for stock setup.
6. I am running just the dump. (ie dp) I don't think that is a problem though as I have had no problems other then the boost not going up past 10 and I think I found out why while doing the install for the chip. I found vac lines eaten away. That fixed my AC at least now I have control of it.

syntax,

It was running better as in only small miss every once in a while and I had the boost problem that I mentioned above to Ed That I found vac. leaks and a broken pipe to the airbox. I do have a afpr but have not been able to put it in yet because of the gauge I have does not fit and I have to go find fittings to make it work, which I will be doing today. But I do have a Walbro 340 in and it IS running rich now. (I put it in when I was running the TE 61 and 3" dp)
 

Raist103

Engine Killer, iPhone Killer, Lawnmower Killer
That is the instruction I used.
I am going to play with it now and see if maybe the chip is not pigyback right although I don't know how I could mess that up. Then find the box my map bar came in and see if I can not find a cross ref. for GM part and this kind.
 

ed hess

race or get outta the way
don
I Think waht youare saying here is you dont really know if you have the correct ultimate for your existing setup. The directions you can dl.
ed
 

ed hess

race or get outta the way
don
if you tole them you want a map sensor for a typhoon you got a 2 bar.
if you told em you want a map sensor for an 89 turbo trans am you got a 3 bar.
what did you tell em?
ed
 

Raist103

Engine Killer, iPhone Killer, Lawnmower Killer
No I don't know for sure but why would he lie about what chip setup it was for I did not tell him aty the time what I want, he just told me he had the chip and I ask what one it was and he told me stock setup one, so I a=said ok that is the one I need and THEN the deal was made to trade.

But nothing is out of the ?

If anyone is avl. with a datamaster and could meet up with me some time today or tomorrow to let me use or help me out call 856-264-3392 or email raistlin103@hotmail.com
 

Raist103

Engine Killer, iPhone Killer, Lawnmower Killer
Well I changed back eerything to stock and it feels better then it has ever. anyway what i am thinking is that either 1. the 3 map bar sensor is bad or not a 3map bar at all (wells part #779-11510) or 2. and I hope this is not the case I was sent a bad chip as part of my trade. :-? So does anyone know if this Wells map bar is a 1, 2, or 3? I had my friend order a AC Delco from his work (GM Dealer, I don't know why I just did not do that to start with but oh well) and I will find out about which one it is then, I should have the map bar sensor in monday afternoon.
 

ed hess

race or get outta the way
put the 3 bar only in and if it runs like crap your stock boost guage doesnt read correctly then you willknow the sensor is ok but the chip is not.
do a little testing and you can figure it out without running back & forth from the store.
ed
 

Raist103

Engine Killer, iPhone Killer, Lawnmower Killer
With the other sensor (I just bought yesterday) the boost gauge will be at 0 vac and when I step on it even just a little it jumps up to 10-15 psi on the stock boost gauge, the aftermarket will only go to 2-5 @ WOT with the new sensor. Any ideas what that could be, chip or sensor?
 

ed hess

race or get outta the way
If i understand this correctly, from what ive learned so far (where is the hell is brian) not being an expert on this yet:
If your stock vac-boost gauge is telling you your at zero vac at idle with the 3 bar sensor and something showing some kinda lets say
8-10 vacumn at idle with the 2 bar sensor (the stock vac boost gauge isnt very accurate. I would say if the above is correct then you do in fact have a 3 bar sensor you purchased yesterday.

Moving on here (hey brian how am i doing so far)

I beleive you now have dl'd the install instructions from brians or atomic rooster website.
I also beleive the ultimate chip must have the oem stock chip piggybacking it.
Lets suppose you dont have the stock chip piggybacking it but an aftermarket chip. I think i read somewhere that it had to be either oem piggybacked or an ATR piggybacking it.
As for id'ing the oem vzs the atr chip, Is there any kind of id on the chip that is piggy backing the ultimate (i.e. the chip you pulled put to plug in the ultimate that you then plugged back in).

from there i cant guide you anymore, but thats as much as i understand which i beleive to be correct.

Ok brian..... take it from there buddy!
 

Raist103

Engine Killer, iPhone Killer, Lawnmower Killer
OK from the way I read it I thought it was the opposite it should NOT be going in the boost when driving, it should be in vac the whole time with the 3 map bar.

Anyone with a 3 map bar please chime in as to what yours does.

Thanks
Don
 
B

Blake

Guest
Get a mechanical boost gauge. That is on the syty list as one of the first things you are supposed to do BEFORE you start modifying. You are going to run into other problems with fueling if you don't do the AFPR right away. Go ahead and replace all the vacuum lines. Did you replace the fuel filter? Do the bicycle tire tube trick that is listed in the tech articles section. If you don't want to start troubleshooting stuff, leave the stock chip in. It is very forgiving as it has a "safe range" for warranty purposes. Doesn't have as much boost, has mph limits, has overboost codes and fuel shutoff(ultimate does this now also I believe), timing isn't as aggressive, etc, etc. Truck must be perfect before doing an ultimate. An Ultimate makes incredible gains by pushing the limits. Shouldn't be pushing the limits until you learn a little more about your truck. That's what most of us are here to help you do. I don't know everything, not by a long shot, but there are a lot of people here that can help guys like us through a problem, but you must be willing to work at it.
 

Raist103

Engine Killer, iPhone Killer, Lawnmower Killer
Blake,

I do have a aftermarket boost gauge, I have changed the fuel filter and the TY runs great with the setup stock, I did replace all vac. lines and the AC works great now, and I will do the afpr tomorrow.(If I can ind a fitting from the gauge to fit the afpr) I have learned a lot already it is stupid problems that are hard to find that I am having the problem with.

I think my whole problem is down to 2 things the map bar was the wrong one which will be fixed monday (That is when the AC Delco one will be in.) or 2 the chip is bad. (which I pray it is not) I had the TY back out today to see the car show in riverside, NJ and it was running great other then the boost not going up past 10 which it did before with a cone filter. The problem I have with that I believe is I went back to the stock turbo from a 61 with a 3" inlet and now I have to crush the rubber/silicone hose from 3" to 2" and I believe it is leaking there. (I don't have the stock hose any longer and will be going to a boat shop tomorrow if one is open to see if they have a 2" 90 or a 2" to 3" hose.)
 

smeagol

Active member
Map sensor sounds like the wrong one.

AC Part number 16040749 from a TTA is the 3 bar.

If you saw your stock boost gauge hit 10psi, just tapping the gas, it means it is a 1 bar map sensor. So your ECM was giving enough fuel for 15psi at off idle. Wonder why it runs like crap? ;)

There is a wrong way to put the memcal on the ultimate board. If you look at the memcal, it is keyed, the keyed portion fits into the slot on the circuit board of the ultimate.
 

Raist103

Engine Killer, iPhone Killer, Lawnmower Killer
smeagol,

That is what I thought, a 1 map bar.

If I sent you a pic of my chip could you paint or photo shop an arrow to what you are speaking of?

I don't see any slots or groves on the Chip, but on the stock chip I see the groves that stick out tht you are speaking of.

Thanks
Don
 
Top