Ultimate V9 problems (still...)

qbnkiller

Conflaguration Specialist
....well, I have been having problems with my UV9 radar-style chip since I got it. I have put the truck up for the winter/spring, and am getting around to running it again, and I thought, what the hell....might try it again...

The problem is the same: If I install the Ultimate+chip, I get a "studering" that is not present with stock 2BAR MAP and stock chip...let me explain it further.

With the DM attached, when the fault occurs (often), is shows the RED banner ECM DISCONNECTED...WAITING FOR RECONNECT, then instantly flashes back to normal. Almost like the truck was shut OFF then back ON again....not an overboost situation...no ECM CODES either.

This year, I (finally) installed the 255lph fuel pump, AFPR (RPM) @ 43# no VAC ., All new vac. lines with plenty of zip ties. New NGK UR5 plugs, new Conrad Cap+rotor, new Taylor plug wires, removed upper intake manifold and hand-polished the inside (I had to take it off to clean the hell out of it, so why not???), while the upper was off, blocked off the EGR hole, but left it attached to the outside, and a new fuel filter.

If I put all the old stock stuff back in, the truck doesn't act up at all, so I assume that the wiring in the truck is fine. As usual, any help would be greatly appreciated...want to start tuning again....have an alky kit to throw in, but I only want 1 headache at a time!!!

Rds.

MAI TY
#1600
:-?


EDIT: By "putting all the old stock stuff back in", I mean the 2BAR and chip....that's all.
 

smeagol

Active member
2 things

1 - are you installing the ultimate chip correctly with the stock memcal piggybacking the ultimate?

2 - are you setting your fuel pressure to 50psi base when you go to the Ultimate chip?
 

qbnkiller

Conflaguration Specialist
...yes I have the memcal installed correctly...I originally installed it backwards, and the truck ran ridiculously rich, with no knock sensor and reallly low MAT temps. When I went to remove it, I saw the faint notches in the stock EEPROM, and reset the ECM and installed it correctly. The 3BAR MAP is installed. The AFPR is set to 43# as stated in the initial posting.....will bump up to 50#, but I cannot see how it could cause the truck to (appear to) shut OFF and ON again.

Thanks in Advance

Alex
 

THEMADTYPH00N

Active member
Same thing happend to me when I installed my ultimate. You need to bump your fuel pressure. The stumble will go away.
 

qbnkiller

Conflaguration Specialist
...OK...will bump FP tomorrow AM, then test to see ??? Even at idle, it will do that neat trick, so....we'll see. Will post tomorrow PM...

MAI TY
 
I just got an ultimate v9 gauge style about a month and half ago and mine is doing the same thing. Plus mine was setting code42 Talked to ghetto sled and he said to send it to him so he can have a look at it. I havent sent it back yet. Probbly will next week.
 

PPI Typhoon

DIY Madman
If you're having a stumble, then the voltage could be doing down so low that it causes DM to disconnect. Just like if you're bogging down a motor (in a stick shift for example) and when you bog it down, the lights dim and sometimes "Check Engine" flashes really quick.

I'd personally focus on getting the tune right rather than focusing on the chip. One of the biggest thing the Ultimate requires in a properly running truck.
 
I would say that mine is tuned pretty well. 21psi on the pitbull chip and 0-1.8 deg knock. and no stumble. When mine stumbles I am going dowm the freeway with nothing draining the bat. If it was a voltage problem then it would do it with the pitbull and it doesnt. It runs fine with the ultimate in I can run the T3 24 on 21 psi with 1.5-22.5 deg of kr so that also says the tune it prety close to dead nuts on.
 

ZavzTy547

Senior Member
I have the V11 chip (gauge style w/knocklight-I love it) but I had similiar issues with stumbling. Come to find out the ultimate was commanding advance timing that my truck did not like. Disconnected the tan wire and found my timing was way off. Adjusted timing to 0 degrees, (reconnected the tan wire) stumble is gone.
 
Timing is 0 deg with the tan wire disconected. Its not a stumble like a timing issue it is a stumble like a like you turn the key off and back on real quick.
 

ty1548

Member
qbnkiller, the fact that the scanner is disconnecting makes me think it is not a tuning issue, but rather a possible bad EPROM or other chip problem. Send me a PM.

Maverick, how many miles on your truck? Are you sure the timing ring on the balancer hasn't slipped? Try advancing it a couple degrees. It really sounds like a timing issue to me. The only times my truck ever stumbled was when I had a bad ground on the ECM, and when the timing was way off. Does it run relatively smooth at idle? How about throttle tip in?

Todd
 

qbnkiller

Conflaguration Specialist
...it seems to be that inreasing the FP to 52# cured the disconnecting problem...now I am searching (endlessly through the tons of results) for the steps for reducing knocking...seems like there is qute a bit from the 2-3 and 3-OD (at peak, >6 KR). I wish the search function was not so fuzzy..


qbnkiller
 
Todd Sorry for the late reply. the truck has 98000 miles on it the timeing is set at 0deg with the tan wire unpluged The balancer is brand new. and has not slipped. All the grounds are clean and tight. I have been running the pit bull in it for A month and it hasent stumbled a single time. With the pitbull or the ultimate in it idles great And it has No tip in stumble. It sets code 42 with the ultimate so I replaced the ing module. And it still settes the code but with the pitbull it doesnt. To me if it was a problem with the truck it would act up with ether chip in it. It doesnt do it on any specific setting on the ultimate it does it on all settings.

Greg
 
Top