vac leak through TB shaft

Does anyone know if gm sells a rebuild kit for the Tb?? Mines leaking boost pretty bad along the throttle valve shaft. How do I fix this?? Is it possible to have a machine shop to machine the TB to accept bushing for the shaft. Thanks for any info....Fern Sy#477
 

sy2185

New member
My problem too. I ordered a new Az. speed and machine TB. only a little more than a stock replacement. Looks sic.
Jeremy
 

mrweelr

New member
Because of this post, I took a bicycle tube and soapy water and did the leak test on my truck today - I'll be damned, the stupid throttle body shaft is leaking on mine too :( This must be pretty common. Funny thing is, I don't have any problems building boost at the line or at WOT. Is this really a problem or are you guys just paranoid? I'm thinking the turbo is efficient enough to compensate for a small leak like this.

Jeremy - how much for the AS&M throttle body? Did you get the stock size or go bigger?
 
My boost fluctuates at wot by as much as 3-4psi. Also it wont stay at 15psi. Itll go there for the 1st to 2nd shift than settle back down to 10psi. Mines leakin pretty bad. I think it is common but no one thinks to check it
 

Hu Ryde

Donating Member
All TB's will leak some. There is no seal, just a roller bushing as for the stock setup. As for an after market TB, it might have bearing rollers and may be sealed.
 

Ian Turgeon

Cascading Inspiration
i think everyone thats tried the tube trick has come up with a leak there.. very common from comments ive seen.

as for its effect, probobly limited, although it would be nice to fix.
If anyone does find a tb replacement that would prevent this, or have a replacable bushing of sorts, let us know.
 

2cold

New member
All the aftermarket TBs that I know of have a roller bearing and seals on the shaft so that they won't leak. Holley Performance Brands makes some nice ones.
 

syclonekid43

New member
does anybody know if the tb off of a 350 or 305 tuneport is the same if thats the case imgoin to change it over because my truck is lost about 3 psi of boost at wot
 

typhoon92

Donating Member
Re: vac leak through TB shaft

Has anyone found a fix for this leaking throttle body shaft leak? Please let me know what you guys did to fix this.
 

dgoodhue

BuSTeD 4.3
Re: vac leak through TB shaft

They are a little expensive, but Carrol Supercharging had a fix to repair the TB for vacuum/leaks. The TB is intechangable with 89-92 GM TPI
 

typhoon92

Donating Member
Re: vac leak through TB shaft

dgoodhue said:
They are a little expensive, but Carrol Supercharging had a fix to repair the TB for vacuum/leaks. The TB is intechangable with 89-92 GM TPI

Thanks, Dave
I'm going to see if i can find a used one at a junkyard. Hopefully the one I get does not leak.
 

dgoodhue

BuSTeD 4.3
Re: vac leak through TB shaft

typhoon92 said:
Thanks, Dave
I'm going to see if i can find a used one at a junkyard. Hopefully the one I get does not leak.

I have a spare TB of a 50K mile Sy FS. As TB get miles the bushing wear, I suspect the leak is larger problem as the TB wears out. Corvette owner complain about the TB linkage binding around 125K miles or so from the bushing wearing out.
 

Sy+Ty

New member
Re: vac leak through TB shaft

Hey guys,

I had my stock TB "rebuilt" w/ oversized bushings by a local company here in town (Austin, TX.) This shop has been doing GM TB's for years & has a reputation for doing good, consistent work. 0 shaft play resulted in a noticeably smoother idle, w/ less "hunting." Best part was, it only cost ~$75!

You can even have these guys bore out your TB to 52MM for For ~$140, incl. the rebuild. I don't have the website handy, but do a search here for posts by Matthew Little (around 2/04), as he posted the info that initially turned me on to these guys.

I just couldn't bring myself to spend $350-400 for an aftermarket TB that others have reported don't produce noticeble gains on our trucks. Instead, parlay that $$ into something that will like Razor's progressive alky kit! <shameless plug for a great product>

Sy+Ty
Sy #1874
Ty #1989
 

Loeryder

New member
Re: vac leak through TB shaft

Sy+Ty said:
Hey guys,

I had my stock TB "rebuilt" w/ oversized bushings by a local company here in town (Austin, TX.) This shop has been doing GM TB's for years & has a reputation for doing good, consistent work. 0 shaft play resulted in a noticeably smoother idle, w/ less "hunting." Best part was, it only cost ~$75!

You can even have these guys bore out your TB to 52MM for For ~$140, incl. the rebuild. I don't have the website handy, but do a search here for posts by Matthew Little (around 2/04), as he posted the info that initially turned me on to these guys.

I just couldn't bring myself to spend $350-400 for an aftermarket TB that others have reported don't produce noticeble gains on our trucks. Instead, parlay that $$ into something that will like Razor's progressive alky kit! <shameless plug for a great product>

Sy+Ty
Sy #1874
Ty #1989

If his email address ends in horsepower.net then I have talked to him and its now $179 to bore it to a twin 52MM, bore and bearing the TB shaft, and that is supplying your own TB.
He will also bore your aluminum throttle body airfoil to match the twin 52 at the same time for free. Obviously he can't bore the plastic ones.

I am on the fence, but will probably go ahead and do this mod when I pull the heads.
 

dgoodhue

BuSTeD 4.3
Re: vac leak through TB shaft

I wouldn't bore the TB to 52mm. When you do that the interior wall behind the throttle plate is really thin in places where the bolt holes are. I had one TB where their was a small hole that poke through backside of a bolt hole. I supose the bolt with seal up the hole, but after reading E-RUE story about poping a leak in his aftermarket TB, that would make me weary.
 
Top