What # injectors to use??

Z SKI

Donating Member
Hey y'all,

I currently have 75# injectors for my stock block build but have decided to pump some E85 through it...

Build consists of built stock block, 9:1 compression, custom grind 220/220 .541 i/e lift 114 lsa, unported brodix -8 heads, EFI carb intake manifold, PTE 6466 gen 2, A/A intercooler, 3" dp, Holley Dominator, etc.

From what I have read I may need more than 75# injectors with E85 and set to kill.. What do you guys think?? 120#?? Will it still be able to idle good or be able to run on a pump gas low boost tune with injectors that big??

Let me know..

Thanks in advance :tup:
 

ajt86

Member
Re: What # injectors to use??

I think 120# is too big if you do a low boost pump gas tune. Id run 80#. Doing a HP estimation with that combo with a duty cycle of 80% i come up with a 85# injector requirement for e85.... i think i highballed your crank HP so 75s may work.... if you have them, put them in... try a tune and see where your duty cycle is. If you wanted to run high boost e85 all the time id go 120, but im pretty sure you said you wanted it to be streetable, i dont think youll be happy with 120s
 

Z SKI

Donating Member
Re: What # injectors to use??

I think 120# is too big if you do a low boost pump gas tune. Id run 80#. Doing a HP estimation with that combo with a duty cycle of 80% i come up with a 85# injector requirement for e85.... i think i highballed your crank HP so 75s may work.... if you have them, put them in... try a tune and see where your duty cycle is. If you wanted to run high boost e85 all the time id go 120, but im pretty sure you said you wanted it to be streetable, i dont think youll be happy with 120s

Thanks bro... Looks like I'll run the 75's and see how far they will take me!!
 

STOUT74

Member
Re: What # injectors to use??

Hey Paul,
I run 120 low-z's on my truck right now on a modded syty ecu. Truck idles perfect, no drive-ability issues. I run e85 to e90. I have a hunch I'm going to run out of injector on the upper end, but that's with a stroked bowtie & a 76mm turbo. I would think for your build 120's might be perfect, especially running e85. I've never run them with gasoline, so I can't speak about them on pump gas. On a side note, for the e85, get an e85 tester. It's just a glass tube with gradation marks on it for ethanol content. Our wonderful government allows "e85" to have an ethanol content for 59% to 90%. The station I get my e85 from has tested 90% or e90 each time. Now with the cost of gasoline coming down, the ratio may come back down. The fuel dealers will mix up the percentages to what ever makes them the most profit. 59% ethanol & lots of boost would be a bad mix. Best to know exactly what your running. I think you might be able to run an ethanol content device like the modern flex fuel vehicles run. I thought I remembered something about the Holley being able to adjust the tune according to the ethanol content. If you go that way, check the auto recyclers first, those new from the dealer are like $700, but I think they're somewhere around $200 used. Also, make sure your pump will keep up with the 120's. I had an A1000 that was having issues keeping up with the fuel demand. I went to a MagnaFuel & haven't seen any issues yet. Also, DO NOT USE PAPER ELEMENT FUEL FILTERS, the e85 will harden them & make then impassable. Use ONLY stainless steel filter elements. Hope this helps you out some. Good luck & take care.
 

TYTILIDIE

METH HEAD
Re: What # injectors to use??

To my memory the Holley does NOT allow the flex fuel sensor but the BS3 does. This is a selling point for me and deal breaker between the two. Gerber I believe runs the BS3 with flex fuel sensor, I could be wrong though.
 

BMFB

Not to scale
Re: What # injectors to use??

75s on e85 is good for 650jp+. You need to make sure you have a pump that can keep up and monitor your fuel pressure
 

e95 Ty

New member
Re: What # injectors to use??

Paul I currently have 120s that are just about maxed (with e98) Idles just fine and is very streetable with my low boost pump gas tune as well. Im looking at going to 160s at a minimum so my 120s may be for sale...
 

0966Sy

Code what?
To my memory the Holley does NOT allow the flex fuel sensor but the BS3 does. This is a selling point for me and deal breaker between the two. Gerber I believe runs the BS3 with flex fuel sensor, I could be wrong though.


I agree, from what I understand the sensor detects the e85 and uploads the tune accordingly?
 

eviltwin

"junkyard syclone"
Re: What # injectors to use??

Just buy holley 120s or 160s. All the injector data will be in a drop down box in the ecm. Easy stuff!
 
Top