What more do i need??

just a 6

R.I.P MyClone
Ok, sense i'm going back to Sweden and taking my truck with me in a couple of weeks . I just bought Pocket Romulator, TunerCat and PLX WB O2 sensor, let the tuning begin.

And i have no clue what to do and where to make changes :eek: So my question to you guys (and girls) are:

Do i need anything more? I have the ultimate so i guess i can use that circuit board, right? But what about chips, can someone tell me what the best chips are for the Romulator. I can get them localy if i know what i'm looking for? Any other info would really help me out, thanks a million
 

just a 6

R.I.P MyClone
jwaller said:
the romulator does not use chips. thats the whole point.

Well i'm sorry i thought the Romulator had one of those new chips that can be erased with electricity instead of UV light. My bad, i told you i don't know shit about this.
 

jwaller

Evil Genius/SyTy Guru
the romulator is a chip simulator. so that you can change the values in it on the fly like you can with FAST and DFI.

once you have it tuned though, you will want to burn a perment chip. at that point you will need a burner and eraser if you dont usse a flash chip.
 

just a 6

R.I.P MyClone
jwaller said:
the romulator is a chip simulator. so that you can change the values in it on the fly like you can with FAST and DFI.

once you have it tuned though, you will want to burn a perment chip. at that point you will need a burner and eraser if you dont usse a flash chip.

Thanks, now it's clear for me :)
 

sy112

New member
more stupid questions, if the romulator is a simulator, how do you get the original program on there. Just copy a BIN over to it?
 

Tim Zapoluch

New member
Hi. You have to start the romulator program. then you select the chip your emulating, which should be a 128k chip. then you go to load buffer, and browse to select the bin you want to use. then you click on the buffer to rom tab, I think it's the very top one on the left side of the screen.

I would suggest that you try and get this all down before you start making changes to the Bin file, as iit can get a little confusing until you get used to it. Be very patient and work very slowly, as you can do a lot of damage if you try to move to quickly. only change one thing at a time, and don't forget to calculate and change the checksum after every change you make. otherwise, the ecm might not read the bin file correctly. Start by changing things like when the cooling fan kicks on and off, until you get the hang of the hardware. Don't expect it to go smoothly at first. And, make sure that the things you're changing actually need to be changed. Start rich with the fuel and modest with the timing. Most importantly, take the time to understand what you're changing and why your changing it. just plugging in numbers can blow up your motor. Don't be afraid to ask questions, and be patient waiting for an answer.

Good luck, and have fun.


Tim
 

InvisiBill

Active member
Just to add some more clarification, the PROM is just a memory chip. You "burn" the contents of a BIN file to it.

The Romulator is a chip emulator. It installs in place of the PROM, and acts as the memory. However, it's not actually a chip. You can simply change the contents of the Romulator's memory using commands, instead of burning a new chip every time. As Waller said, you'll want to burn your final setup onto a chip to leave in the ECM when you're done.

FYI, our trucks use a 27C128 EPROM by default. 29C___ is the EEPROM (electronically erasable, instead of UV). I've only seen the 29C's in 256 and higher, so you'll have to double up the BIN file (make one file with two copies of the data) or make sure that you burn the data to the end of the chip.
 
Top