what Push Rods to use

TurboJunk

questionable
Im putitng my motor together and im using the same push rods that came with my brodix heads. now that im using vortecs i think there too short. when i go to tighten up the stock rockers there still flopping around. im using then cause there COMP CAM push rods that were new when the motor was built by the previous owner.

I have factory push rods that came with my vortecs and a set of tock syty ones (but i have to go and pick them up if i had them in hand i would of compared them) .... are these good enough with a aftermarket cam??

if not what is the part number for a good aftermarket set (comp cams etc etc.)

CHARLIE
 
Last edited:

TurboJunk

questionable
Re: what Push Rods to use

at my shop i deal with a wholesale distributor KEYSTONE. Its easier for me to order them next day from them. but thanks anyway

Anyone have any suggestions!
 

Merk

Donating Member
Re: what Push Rods to use

Im confused.

You have Comp Cams, or want Comp Cams?
You are using Brodix or Vortec heads?

Who is Keystone?

Told ya I was confused :lol:
 

James Thomas

"NO CLASS"
Re: what Push Rods to use

I have not "personally" had a failed stock 4.3L push rod with a stock or "mild pattern" cam but I am sure that there are those that have. It really depends on how radical your cam profile is because higher lift, "faster" lobe rates and higher r.p.m. do put extra stress (a lot!)on all valvetrain components. I personally would not feel real bad about stock push rods on a 412 / 415 type cam with low r.p.m.'s but would not use stockers above that at all. Bottom line....... is you new engine "worth new good new hi performance" push rods to you.... or not? I would think yes :2cents:
________________
James Thomas
 

MikeRenz

not stock
Re: what Push Rods to use

these are the push rods that i got (from Keystone also)
Crane Cams 95624-2 (i think)
cranecamspushrods.jpg
 

Loeryder

New member
Re: what Push Rods to use

Mainly you want a 1 piece hardened pushrod.
Alot of them have the ends welded on, instead of being machined out of a single piece of steel.

Manleys are 1 piece and you can get them from Michael Hood for $99.
Thats what I am goin with.
 

sytyguy

Moderated User
Re: what Push Rods to use

We use a 5/16" diameter, 7.200" long, ball/tube pushrod in stock form. Best thing to do when going with an aftermarket pushrod is to upgrade to a one piece design. Below are the one piece designs that work with our stock(ish) configuration:

Crane 95624 - 7.200"
Crane 95625 - 7.250"
Comp 7940 - 7.200"
Comp 7944 - 7.250"
Manley 25733 - 7.200"
Manley 25734 - 7.250"

* add -12 for a V6 set or -16 for a V8 set (V8 sets are in stock usually)

I listed the 7.250" rods because (a lot of times) they're more readily available. FWIW, Manley makes the pushrods for Comp and Crane, so Manley is usu cheaper, due to cutting out an extra middleman.

Hood
 

Don W.

Stab it and steer it
Re: what Push Rods to use

TurboJunk said:
Im putitng my motor together and im using the same push rods that came with my brodix heads. now that im using vortecs i think there too short. when i go to tighten up the stock rockers there still flopping around. im using then cause there COMP CAM push rods that were new when the motor was built by the previous owner.

I have factory push rods that came with my vortecs and a set of tock syty ones (but i have to go and pick them up if i had them in hand i would of compared them) .... are these good enough with a aftermarket cam??

if not what is the part number for a good aftermarket set (comp cams etc etc.)

CHARLIE

Correct push rod length is vital to proper valve train ops. you need to figure out why they're loose. Proper preload on the hyd lifters will still let you twist the rods (assuming valves closed of course) but they shouldn't be "loose.":2cents:
 

TurboJunk

questionable
Re: what Push Rods to use

Merk said:
Im confused.

You have Comp Cams, or want Comp Cams?
You are using Brodix or Vortec heads?

Who is Keystone?

Told ya I was confused :lol:
Keystone is a wholesale parts distributor that i deal with, have vortecs now sold the brodix, and i have comp cams !!

thanks everyone. right now i have comp cams psh rods 7938 7.100" im going to order the MANLEY ones 7.200" thanks again
 
Top