When should one upgrade the TB?

Logan

Member
I am gathering parts for my new build and I am kicking the idea of a bigger throttle body around. Now, with that said I would rather not through $300+ at something that is just going to look cool. I know there is a flow difference between the stock, a 52mm and a 58mm but I guess I am wondering if the bang to buck ratio is there.

With that my question is at what point does it really benefit an engine to have a bigger throttle body or more so at what point does the stock unit start to hurt performance?

I am working with the following:

60-1 Turbo
A2A
Meth injection

Engine:
Forged pistons
H-beam rods
custom grind cam
stock Vortec Heads.

Keep in mind that this is a street truck with no track intentions, just something fun from stop light to stop light. Thanks for any advice.
 

Jimmy

Banned
Re: When should one upgrade the TB?

I am gathering parts for my new build and I am kicking the idea of a bigger throttle body around. Now, with that said I would rather not through $300+ at something that is just going to look cool. I know there is a flow difference between the stock, a 52mm and a 58mm but I guess I am wondering if the bang to buck ratio is there.

With that my question is at what point does it really benefit an engine to have a bigger throttle body or more so at what point does the stock unit start to hurt performance?

I am working with the following:

60-1 Turbo
A2A
Meth injection

Engine:
Forged pistons
H-beam rods
custom grind cam
stock Vortec Heads.

Keep in mind that this is a street truck with no track intentions, just something fun from stop light to stop light. Thanks for any advice.

The stock one is fine.
 

Logan

Member
Re: When should one upgrade the TB?

Thank you for the response. I have just seen a lot of chatter when I was searching about upgrading and I just couldn't find a concise answer either way.
 

DaveP

Active member
Re: When should one upgrade the TB?

stock is 780~790cfm

At what pressure? Air flow numbers are meaningless for comparison without knowing the test pressure or vacuum utilized.

I've never flowed a stock TB. It was first used on the 5.7 TPI engine. Using an online calculator, I put in 350 cubic inches, Volumetric efficiency of 1.0 (high) for a N/A engine, and 5700 RPM which is what my TPI engine red-lines at. The flow is 577 CFM.

Then I calculated 2.0 efficiency (14.7 psi boost) but 262 cubic inches at 4500 RPM, the flow is 682 CFM. (Stock SyTy). Not too far off from the N/A 5.7 this throttle body was developed for.

The consideration is at what pressure does the throttle body present a meaningful pressure-drop at full boost? I posit that the inter-coolers and piping present a larger restriction than the throttle body does in many configurations. Until the RPM and boost goes up significantly, requiring more air volume, the throttle body isn't a restriction.

Understand that the ECM-controlled boost control setups in SyTy's are positive feed-back systems. The compressor is on the up-stream side of the throttle plates. The MAP sensor is on the downstream side. So the ECM will add what ever it needs to to obtain the "desired boost" after the throttle plates. If the throttle body presents too much of a restriction, the control will be laggy and wavy, and result in pressure fluctuations.

A meaningful test for TB restriction would be to monitor the pressure before and after the throttle body. I doubt there's any measurable pressure drop on a streetable SyTy with a stock throttle body.

Not knowing a damn thing about this, I would say if your boost control is smooth, and not "wavy" at WOT, your throttle body is not restrictive, and doesn't need to be enlarged.
 

DaveP

Active member
Re: When should one upgrade the TB?


" All CFM values are corrected for airflow at 28 inches of water."

Thank you. That helps a lot. 28" of water column is very close to 0" vacuum, 1 bar, or 14.7psi absolute. So those flow numbers are valid for a N/A engine.

I think I'm still right that it will flow a heck of a lot more under positive pressure, and that using a volumetric efficiency of "2" in the calculator I used represents 14.7psi gauge, 2bar, or 29.4psi absolute. Which is stock SyTy.
 

JSM

Active member
Re: When should one upgrade the TB?

I would also suggest based on gut feeling, experience the intake itself (along with intercooler) is the weak link. I have noticed every engine I put an aftermarket intake on woke up, and I don't think it was due to TB size, but the removal of stock intercooler and intake itself.
 

Logan

Member
Re: When should one upgrade the TB?

I am going to run the RPM A2A so hopefully that is a little better than the stock set up. If anything it is at least a weight savings and less moving parts. Also, I have yet to read any complaints from people who have converted to A2A.

Based on everything you guys have said I am definitely going to stick with the stock set up. I have also tossed the idea around of doing a different intake but I feel like I would be putting a bit more money into something that is better suited for the guys aiming for bigger numbers. If I end up with a 375hp truck I will be super thrilled.

Thanks for all of the information.
 

dgoodhue

BuSTeD 4.3
Re: When should one upgrade the TB?

My intuition tells me that the upper intake is a bigger restriction. One issue that many don't think about is a larger throttle creates an off idle throttle tip-in issue; to resolve the tip-in it would need ecm tuning.
 

It's just a six

Super Member
Re: When should one upgrade the TB?

The stock intercoolers restriction is in the inlet.
My friend cut off the 2" inlet & installed a 2.5" inlet & it picked up a bunch of CFM. Cant remember off hand what the numbers were, but were tested @ 28"

I don't think the intake is a restriction, uneven airflow,,, from what I hear, yes.
 

dgoodhue

BuSTeD 4.3
Re: When should one upgrade the TB?

I guess that I should qualify what l wrote about the stock upper intake being restrictive. On a stock motor with LB4 head & stock heads cam, I would bet the stock intake isn't the restriction. A larger throttle body still probably is going to do jackshit on a stock motor. With Vortec heads (and even more so with Brodix heads) and more aggressive aftermarket cam, you can increase the air flow by 50% vs the stock components, which is when i think the stock intake becomes a restriction.
 
Top