Wiring to Shurflow IC pump

Lynn D. Brown

New member
Hey Guys,

I was thinking of using the stock connector to hook up juice to the Shurflow pump. It looks like 18 gauge wire, and the pump plate says it pulls 4 Amps at 45 Psig. The pressure drop around the IC water loop is probably no where near that, so it seems like that should be plenty of wire for the job.

From electrical charts, it looks like 18 gauge would have ~ 1 Ohm of resistance for ~ 10' of wire, which doesn't seem like a whole lot. What did U guys use ?
 

TYRODD

My ass. Look at it.
Hmmm, the wires coming out of the shurflo are like 12~14, I think. I would use something between 12 and 16, I too used the stock weather-proof connector, I just soldered the wires together and heat-shrunk'em. I wouldnt think anything bigger than say 18 will make a difference as down the line, the wire is going to be 18, but going smaller than the old lines may cause problems.
 

Lynn D. Brown

New member
Wiring the Shurflow

Wiring the Shurflow

Yeh, been working on it since the 1st post, and I agree with U. I don't think I will use the stock connector. For one thing, it connects to the system that only turns it on at high temp. I would like it on when the engine is on. And the pump wiring appears to be 14 gauge, which is much thicker.

So, I think I will wire it to a 12V IGN source so it turns on when the car is on. I think I will put a switch and a fuse (probably 10 A) in the line also.

I guess the existing pump is tied into that relay and wiring post on the back Pass side of the firewall, right ? Is that wiring junction tied into the IGN switch ? If it is, I could connect there.
 

TYRODD

My ass. Look at it.
Actually I did use the stock connector, I just cut off the pigtail from the stock pump and soldered the shurflo's wires to it, doesnt really matter though, I just thought it would be kind of neat, and if I had to take the pump out for any reason, I wouldnt have to cut the wires.

As far as the hot wiring the pump, This is a great, easy mod. All you have to do is ground the wire from the relay, no 12V needed to tap into.

What I did was tie into the yellow wire coming out of the relay (pass. side), ran the wire stealth like through one of the grommets in the fire wall.

then I placed a low profile switch on the underside of the dash, connected the end of the wire to one side of the switch.

From the other side of the switch I ran another wire back through the same grommet, and grounded that wire to the engine ground directly to the right of the wiper motor. This way nothing looks funny, just stock, this is important to me. I even soldered and heat shrunk every connection, it just looks so much cleaner.

With the switch you can control when the pump is running. It will still only run with the key on, but it is nice to be able to shut it off when working on the car and not needing it on.

I usually leave it on all the time, unless like Im working on it (which is a lot :) )
 

Lynn D. Brown

New member
Wiring Shurflow

Wiring Shurflow

Excellent idea, Rodney. You changed my mind back. I have a 2 conductor female plug already that will fit in. All I need to do is see if any of the AP stores have the connectors. I see the yellow wire coming out of the relay on the drivers side, so I'll just cut it and run that in and out of the car. Got the pump mounted and hoses connected to it.

I think U mean "chassis ground" on the firewall, don't U ?
 

TYRODD

My ass. Look at it.
I think U mean "chassis ground" on the firewall, don't U ?

Uh, yeah :oops: . I try to run all grounds there, Like for the IC pump and my remote start, looks mo betta there. About the yellow wire, Just splice into it. Actualy, I did cut it first, only because I had to slip heat shrink around the connection, slip the HS down the wire, solder the wires back together, and add the new wire, It will look like a "Y", then just slip the HS back up and shrinkerthenyurdone :p .

Where did you decide to mount the pump? Also, if you ran the Heater hose through the fender well, find some "C" shaped heater hose (NAPA) to make the bend around the Upper IC, I kick myself everytime I see the 90 deg. elbows I used, looks dumb. I plan on swapping those out soon.
 

Lynn D. Brown

New member
Shurflow wiring

Shurflow wiring

Rodney,

So U don't cut the yellow wire, U splice into it and ground it thru a switch ? So, if U open the switch, then it will work like stock, huh ?

I mounted my Shurflow on the platform that comes with the ATR Batt Relocation kit. It puts a shelf in front of the Pass tire, and I decided not to put the battery there. It gives nice solid support for the pump using the bracket that comes w the pump and the hoses flow in & out nice and smooth w/o any kinks. I bought some of those 3/4" hose 90's for connecting to the Upper IC. I may even put a tee and a valve off the IC top connection and put a little valve on it to bleed off air.

I'm wiring it now to the stock pump connector using the same 2 conductor GM Weather-Pack connectors that are already on the car. Pep Boys and NAPA carry them.
 

TYRODD

My ass. Look at it.
So U don't cut the yellow wire, U splice into it and ground it thru a switch ? So, if U open the switch, then it will work like stock, huh ?

Exactly!

I have a real bad air lock problem, my aux. CCHE has its input and output on the bottom, which traps air. Little by little, the pump burps air out of it. I am going to pull the aux. out and install a petcock on the top to vent out air. Another good point about the shurflo is that it will run dry without damage. In fact, the diaphram inside is rubber-some people who have bought these pumps from us have used them for HYDROCHLORIC ACID! i.e.,they are a very good pump.

I'm wiring it now to the stock pump connector using the same 2 conductor GM Weather-Pack connectors that are already on the car. Pep Boys and NAPA carry them.

Wow, good to know, glad to know I can get them for a fair price (not from the dealership).
 
Top