knock, knock...and other stuff

4C FED

Absolutum Dominium
Re: knock, knock...and other stuff

Thanks Josh
Tooky said:
I looked at your DataMaster file. It sounds like you covered all your bases. It even appears like your WB02 Datalogging is in the file and flawless at 11.8. Your RPM line indicates to me that it's not a stock converter. What converter are you running?
No wideband, it's all stock with the exception of the ATR IC & the Ultimate for stock inj. & heads.
TC is from George Blake, stock style, a little higher stall.

Tooky said:
The boost control is also outrageously bad. Have you considered trying a manual boost controller like the BoostValve.com ball-and-spring unit like I run? I also don't know what turbo you have.
I have a manual controller, but I'm not so sure that's what the problem is with the boost. It's sporadic. Sometimes it's spot on and steady other times it sucks.

Tooky said:
The knock does seem to rise with boost but that doesn't "guarantee" it's still not false, possibly.
It comes & goes. Same gas & everything else.
 
Last edited:

4C FED

Absolutum Dominium
Re: knock, knock...and other stuff

Replaced knock sensor yesterday. PITA, definately a job for people with small forearms.
Went for a run this morning while going to store.
First run Gtech logged 13.37 @ 108.3
Datamaster F'ed up a dropped a whole bunch of data. A pretty worthless log.
I was able to see what started out as 1.6deg. of KR @ 14.6psi & ended up with 1 deg. of KR @ 18psi.

Second run after truck sat in parking lot for about 20 min.
Gtech logged 13.33 @ 107.2. Tranny was all warmed up ~180 deg., I left @ about 3500 rpm & 15.5psi.
I'm curious about the TC stall since it's supposed to be just a little more than stock. I wonder if the TC is to loose or fubar'd.
I used Tunerpro this time as it seems to never drop data. I had 7 deg. of KR @ 19psi.
:rant:
Here is the Tunerpro log It's the last one from today, "new knock sensor."
Again, boost control sucks.
I'm going to do a compression test today, swap my plugs out again for Iridiums & look underneath the truck for loose things that may be causing this.

I have one question that I thought I remembered seeing about the DP bracket that goes to the trans. When I reinstalled the trans I didn't put this back on. With that bracket gone, could it cause false knock?

I want to lay this issue to rest so I can install new turbo, DP & switch to code $59. ARGH
 
Last edited:

4C FED

Absolutum Dominium
Re: knock, knock...and other stuff

Well I think that whatever is causing the knock made itself audible today.
I drove to the bank & parked for about 5 minutes while I made a deposit. When I started the truck everything was normal. When I put it in reverse I heard a clacking noise. Put it in neutral, noise gone, put it in D noise comes back. Drove it home nothing unusual happened, everything seems normal except for the clacking noise.
It sounds like the noise is right around the converter area.

To much yard work to do today. It'll have to wait until I have some free time.
Hopefully it's something simple like a bad converter or a broken flexplate.
 

turbodig

Active member
Re: knock, knock...and other stuff

Lots of potential problems here.

Looks like your fueling tune isn't the best.

You got either a leaky WG servo, or related plumbing, and/or a partially sticky WG flapper.
(probably only sticks when warm)

Need to get a wide-band on there, and get your ultimate patched for whatever WB you get.

Noise could be converter bolts, but it could also be uglier....

TCC engage looks a bit mushy...
 

4C FED

Absolutum Dominium
Re: knock, knock...and other stuff

turbodig said:
Lots of potential problems here.

Looks like your fueling tune isn't the best.

You got either a leaky WG servo, or related plumbing, and/or a partially sticky WG flapper.
(probably only sticks when warm)

Need to get a wide-band on there, and get your ultimate patched for whatever WB you get.

Noise could be converter bolts, but it could also be uglier....

TCC engage looks a bit mushy...

Thanks Dig. I'll check those things out.

10-4 on the TC engage. It's been that way from the get go since the rebuild. I have a feeling that when I first installed the trans & accidently plumbed the lines into the oil filter backwards it may have damaged it. It certainly wiped out the pump with the lines backwards.

I'll go ahead and order the WB.
Would you recommend I ditch the Ultimate & switch over to code $59 or work out my gremlins with the Ultimate first, then switch?

I used locktite (red) on the TC bolts. Flexplate has never been off to my knowledge, but maybe those bolts could be loose.
When I get home tonight I'm going to unbolt the converter, push it back & start it up to see if the noise is still there.
 

4C FED

Absolutum Dominium
Re: knock, knock...and other stuff

I'm pretty sure I found the source of the clacking noise from last Sunday.
While under the truck hooking up the trans pressure gauge today ,I found that I had failed to bolt the xfer-case vent bracket back to the bellhousing. This happened when I was installing the braided steel fuel line a couple of months ago. The bracket was wedged in between the bellhousing & trans tunnel.
I also saw that my drivers mount looks like the rubber is seperating from the steel. This along with the bracket stuck where it was & when I put it in D or R would cause the motor to move excessively and cause the bracket to rub against the bellhousing & trans tunnel.

That's my theory.
I'm 51% sure this is what was making the noise, but I'm still checking everything out underneath the truck making sure nothing is loose or rubbing.

EDIT:
Well that theory was short lived.
After letting the truck sit for 15 minutes I went out to drive it again & when I put it into gear the noise came back.
Climbed underneath & the noise is coming fron the front of the trans. I used my mechanics stethoscope & put it on the pump. I couldn't hear any unusual noises. So it looks like something is toasty in the TC.
 
Last edited:

4C FED

Absolutum Dominium
Re: knock, knock...and other stuff

Tooky said:
Sorry to hear that Rick :(
It's all good. Summers around the corner & I'll get a good ab workout getting up & down from the creeper

When unbolting the TC yesterday I noticed that I set the TC stab depth on the small side @ about 1/8". I wondering if TC broke the pump.
 

4C FED

Absolutum Dominium
Re: knock, knock...and other stuff

I revisited looking for causes for the KR again today.
I had orignally torqued the knock sensor to spec. ~14 ft lbs. Today I tried tightening it more which only aggravated the KR even more. At some times the KR graph was higher than the boost graph.
So I decided I'd try what some have done which was to tighten the knock sensor only hand tight.
This gave me 2.8 deg. KR @ 4.5 psi. which I still think is false knock, probably lifter or rocker noise, since it went away at even higher boost levels. Boost was nice & steady
Now I notice I have Code 42 present. I think this might be due to the dist. being installed off a tooth which has necessitated rotating the dist more clockwise to time it correctly. This is putting a strain on the main harnesss connector that goes to the dist.
Here's a screen cap from today:
2623991228_507ff14b06_o.jpg
 
Top