009 calibrations

10secTy

Sy-Ty builder and Tuner
We used the 009's in Tonys truck with very good drivability. But like Mark and Brian wrote the 50's would be easier to tune. And for your combo Brian has the 50's worked out already. We went with the 009's because they where cheap and we knew that because of Tony's cam and heads we would be tuning anyway. Are we insane for using the 009's? I don't think so it took some tuning but hey thats how you learn. Tonys truck drives better than it did stock. But your truck is more of a no brainer, Brian has done alot of work on the 50's which will bring your tuning time down to nil. Don't be scaried off by trying something different but be prepared to spend the time on it.I am not saying that this injector is better than that one. Just that certain ones can give you more driving time than tunning time.
Which ever way you chose I can give you a hand with the tunning.

Later

Nolan

_________________
1993 Synoma 12.27@112 mph
1992 Typhoon under construction

<font size=-1>[ This Message was edited by: Canadian SY/TY on 2001-11-01 01:11 ]</font>
 

smeagol

Active member
I thought of dumping fuel in if we overboosted.. it's possible, but would take some time to write in. Not sure if I have time available for that purpose, I'm already spending too much time doing regular chip work. Also, it would benefit mostly the smaller turbo guys. Already, there are truck builds that I hoping to use the 50# chips on that will need most of the fuel the 50s can deliver. Going static with the injectors at that point won't do a whole bunch as far as helping to lower boost, or overfueling to keep it safer. The Syclone I'm working on now is running like 10:1 AFR at 15psi (very rich). Before we had the wastegate setup going, it would still overboost easily, telling me the extra loads of fuel won't help to keep boost down, but would keep the fueling rich enough for safety.

Quasi-asynch stuff - yes you have it correct. In the syty ECM setup, you have the option of using it, and it is wrote in the software so as to switch between synchronous and quasi-asynch... I tried using that method, and no matter what I did, there was still a noticeable transition. I just liked the way it ran under quasi-asynch. I tried running it full time QA, haven't seen any problems doing it this way, so I've left it.

As far as the 50# config with the box and whatnot...I'm still up in the air on that. I'm hoping to get this Syclone tuned, then Opie's Ty. The sy has headers/TE45/air-air..opie's has TE44 and stock everything else. This should basically be two ends of the spectrum as far as stock motor buildups go, so I need to see how different they are, to try to cover all bases.

Brian G
 

kwick6

Donating Member
Brian,
What happened to the diy-efi site?
You also had a chip page going, and I thought that was an excellent source??

As far as the overboost goes, I would think that since the chip still looks at the map sensor for boost, couldn't something be programmed at say 25psi to retard timing and dump fuel in?

I am really interested in hearing more about the work that you will be doing with Opie's ty...because he has a similar setup as I do.
It would make for a nice upgrade from stock, without changing cam, heads and would allow for someone to get involved with the tuning since that truck would be really closely dialed in. I see a lot of people wanting to go crazy with their builds, maybe with Opie's ty it will show people to slow down and not change too much right away. I am looking forward to hearing more about his truck. Will he be running open loop all the time?

Could you describe in a little more detail the way open loop and closed loop works. What is open/closed loop? It sounds beneficial, and you seemed to really like the way your truck ran in that condition.
Please clarify... something like idle fueling would be a little rich, and it would get hotter at WOT.
So the idle being rich could be bad for the cat? In your opinion, what would be ideal, without emission concern or cat damage, open loop?

As far as switching between the synch. and quasi-asynch. If you have it programmed to run quasi. at idle, have you tried to switch it to synch. at cruise? Maybe running the open loop, where it is hotter at cruise, would benefit more from the two injector pulses...just a random thought.

So with the stock, batch fire, all the injectors will fire every 360* of crank rotation. The quasi-asynch will deliver a single pulse per injection event, so when is the injection event with this set to?

The syclone that your working on now, are you trying to get boost control programmed into your chip? What was causing the overboost, you describe before you had the wastegate setup going? Were you having trouble with the wastegate or something? Was the spring too strong in the actuator? Im just wondering because without the chip controlling boost, wouldn't all the boost control *have* to come from a independant controller? What is the reason for running the 10:1 AFR? Is that something that is demanded by the chip? I forget what the stock AFR is, but since it is a certain amount, will the truck make adjustments to duty cycle and other stuff automatically to achieve that?, or will you command the injectors and other stuff until you achieve the desired AFR? Is that AFR constantly maintained or will it change at different engine speeds? ie. idle, off-idle,cruise,WOT I think this is where speedpro probably comes in and does things automatically to calculate what is need to get a specific AFR.

I will stop there for now. Thank you for any help you offer.

Scott
 

smeagol

Active member
yikes too many questions to answer

Chip page is still up .. just kinda hidden
:wink:

Overboost - depending on how I set the programs up, I could just program in static fueling at 22psi on a chip set for 18-20psi, sure. Timing is already dropped huge at overboost conditions, in 3 bar calibrations, for this same reason.

Opie, as well as a couple other trucks, has been running open loop for a while. Open loop is no 02 feedback.. the 02 sensor is there, you are still taking readings, but the BLM & Integrator aren't updated. Basically closed loop desires 14.7:1 AFR at ALL times, other than at WOT, or at cold startup, until truck is warm. With open loop, you can run a bit richer at idle, for smoother idle, a bit leaner at cruise, for better MPG, and won't have an integrator trying to correct. From what I've seen, a truck in closed loop that is running good (via integrator numbers) just doesn't feel *smooth* (seat of the pants). Go open loop, almost every person likes the feel of it.

QA versus synch fueling - i see no advantage of switching between the two in a calibration. Tons of R&D may show me some differences.. but until then, I'll stick with QA. From what I saw, if you calibrated a truck with stock type fueling, then changed it to QA..you have to retune the whole calibration. Big PITA, don't wanna do it again.

Boost control - the Sy i'm working with now has the PTE setup. It has a high pressure spring setup, so base boost is 16psi. The problems arose from a burned up actuator..replaced it, all good. No computer control at this time, I wanted to dial it in at 16psi, then play with boost control. From the little I have played with boost control with the PTE setups, it's very simple to control. Probably would have great results with bleeder valves on these setups even... (great results being a relative term :razz: )

AFR- stock setup knows NOTHING about what AFR actually is at WOT. It is just using programmed values to deliver fuel, whether it's rich or lean. I programmed the 50# chips, so I set them rich for safety's sake (and very rich, from the looks of things). Now that I'm wideband tuning, I can play with that WOT fueling with relative safety.

Brian G
 

kwick6

Donating Member
Why is the page hidden? :smile:

So, the 02 sensor is not giving feedback in open loop. Is it true that the only operation for an 02 is to command either rich or lean? So is the 02 sensor, in open loop, not commanding the 14.7:1....rather whatever the chip decides it to be. So when you changed that sy to have 10:1, what did you have to do? What told you it was at 10:1?
Maybe the use of the wideband is telling you it is 10:1.
What did it require you to do to get your 50lb chip to be rich. Was it the fact that you have now found with the wideband what is needed to produce a 10:1? and now you just worry about the WOT?

Thanks,
Scott
 

smeagol

Active member
Yer still confused.

Chip page http://www.members.home.com/unskarred/chipping.htm

So, the 02 sensor is not giving feedback in open loop.

It is giving an 02 reading, but there is no feedback from the ECM, making adjustments on those 02 readings. It sees the 02 readings, and says, OK, whatever, I don't care. :wink:

Is it true that the only operation for an 02 is to command either rich or lean?

With stock 02 sensors, yes.

So is the 02 sensor, in open loop, not commanding the 14.7:1....

Correct.

rather whatever the chip decides it to be.

It isn't commanding anything. It is delivering fuel, based on the chip's calibration. The AFR is whatever you read it to be at certain conditions.

So when you changed that sy to have 10:1, what did you have to do?

I didn't change it to 10:1. I set it as rich, and had no clue what that AFR was.

What told you it was at 10:1?

I recently began tuning it with a wideband 02.

Maybe the use of the wideband is telling you it is 10:1.

No, the wideband was telling me it was 10:1.
:wink:

What did it require you to do to get your 50lb chip to be rich.

umm, a rich calibration.. just set the fueling very rich in the tables for safety's sake.

Was it the fact that you have now found with the wideband what is needed to produce a 10:1? and now you just worry about the WOT?

No i haven't 'just' found the wideband.. this is really just the first time I've had an opportunity to get good data with the 50# calibration on a truck that is running good.

So i've been concentrating on the drivability of the chip, as I can use the stock 02 for such tuning. That is really the hardest part of the calibration. IMO, that part is about done, and it's time to get the WOT stuff done.

It's easy to make such a rich AFR.. throw a set of 40s in your truck, you'll have as rich an AFR in your truck, just no drivability :smile:

Brian G
 

kwick6

Donating Member
Ok. I see. The thing I don't understand is how you set the fueling tables very rich.

I wasn't sure if you needed the data from the wideband to know what ballpark to set the fueling to.ie...the wideband shows we made it too rich.

As far as the 40's go, if I were to install them in my truck I would not have driveability unless I went to an open loop and started to lean out the fuel in cruise and WOT?

Thanks for posting the chip page.

I'll leave ya alone now.

Thanks,
Scott
(still very confused) :smile:
 

smeagol

Active member
Ok. I see. The thing I don't understand is how you set the fueling tables very rich.

Big values :wink: Basically saw on Diacom that my 02s were very high.. and that the truck was running safe (no knock, plugs were good), then didn't mess with it much beyond that.

As far as the 40's go, if I were to install them in my truck I would not have driveability unless I went to an open loop and started to lean out the fuel in cruise and WOT?

No.. more to it than that. I don't suggest you do 40s.. it'd require some patience and chipping skills...

I suggest you wait and use a calibration for some larger injectors, whether it's some 009 cals from Dig etc, or 50# cal from me.

BG
 

BigAl...

Member
HOLY SHIT!!! AFTER THAT THREAD I'VE DECIDED. LOW MILAGE TRUCK FOR SALE (just kidding) Brian, You the MAN!!! but it doesn't seem like you'll ever really have a 50# chip available (correct me if I'm wrong) because it seems like you're doing alot of custom/specific tuning for these trucks ie opie. after you finish these trucks, will you be able to produce a generic/one size fits all chip like your ultimate (or am I in fantasy land)? I remember you mentioning something about a WOT pot. switch to control WOT fueling is this how you plan on covering all of your bases? at what point do you suggest we start wanting a 50# chip? I personally want one now because of the way you guys say how well it idles and cruises

TIA
BigAl...
 

smeagol

Active member
will you be able to produce a generic/one size fits all chip like your ultimate ?

That's really the dilemma.

Opie's truck isn't really one of the custom ones that I'm doing as a task, it's more of an experiment, and a truck I'm basing the calibration off of (partially).

I'm not sure how to tackle the problem of different build ups & recipes. Is the WOT fuel knob a solution? Maybe. It may end up to be worthless. It may end up to be just a fine tuning aid. It may end up to be a knob used as a boost controller. I'm not sure yet, but I like the potential it has.

The chip is closer to being ready, but still not yet. How long? I don't know. It's been too long already. Unfortunately, tuning goes slow. I made a *lot* of progress on my truck, but the WOT stuff has to be done on trucks that people will copy the builds of. IE Jerry's Syclone and Opie's Typhoon. Opie is either out of town or the truck has problems, Jerry's truck just got together, and winter is coming.

Brian G
 

Irid

New member
I for one am *very* interested in how Opie's truck turns out. Basically, I'm hoping to copy his build (bolt on PTE setup, standard other upgrades like an AUX CCHE, walbro 255, but stock TC, heads, etc.)

I'm pretty much "cash in hand" hoping for the software to come together, then I'll throw down for that and the PTE and scare some locals :wink:

So know that there are people out there who appreciate your efforts a ton!
 

Buster

New member
Just take a look at Jordans truck, that's pretty much the best you'll do with a stock Ty and a big turbo.
 

smeagol

Active member
Just take a look at Jordans truck, that's pretty much the best you'll do with a stock Ty and a big turbo.

Maybe, maybe not..

Yes, he sets a very impressive benchmark.. but there may be still more to learn, and more potential there. I've known maybe 3 people with all out stock motor Typhoon builds. All out means headers, air-air IC, big turbo, fueling mods, and big boost. Mike's Ty ran well, before he went BIG. Todd still had stock exhaust manifolds, running 12.17. I've knowno of only several Sy's at this level on the stock motor as well. The fastest was Dr. Brinski's syclone...I recall it hit 11.66 with the stock motor. That's with a 62, DFI, big air/water IC, built trans & stall, and serious suspension work (his words). My whole point is that Syty's haven't had a TON of guys pushing the performance with the big bolt ons, like Buick guys have. Yes, many guys blow up the trucks, but what if you run it safe, without detonation, for a long time? Do headers/turbo/IC upgrades contribute to removing heat from the chamber, allowing the pistons to live with increased power/cylinder pressure?

Jordan's truck has more potential IMHO. His 60' times weren't as impressive as his ET would lead you to believe. His truck has never been tuned chipwise, with a wideband 02. Would he benefit from less boost with more timing? Or is he onto something with the high boost/LOW timing setup? Would a taller tire help? Would shifting into OD help? Would 1.6 rockers help?

Just throwing some things out there..

BG
 

jwaller

Evil Genius/SyTy Guru
yes....yes ....yes....the sleeping giant comes out of the closet....good to see you again BG..
 

Buster

New member
On 2001-11-02 19:10, jwaller wrote:
yes....yes ....yes....the sleeping giant comes out of the closet....good to see you again BG..

He can't resist us, sytys are still virgin, as compared to those used, beat up, over modified TTA's.
 

turbodig

Active member
On 2001-11-01 16:37, Red Canyonero wrote:
will you be able to produce a generic/one size fits all chip like your ultimate ?

That's really the dilemma.

This is really quite an understatement.

Boil down the question, and it comes to:
"How good is good enough".

If 75% of your max potential performance is
good enough, then a one-size-fits-all chip
will be enough for you.

If nothing less than the fastest you can go
will do, you're never gonna be happy with
anything but a full-custom tune.
(IE, with a Wide-band)

Opie's truck isn't really one of the custom ones that I'm doing as a task, it's more of an experiment, and a truck I'm basing the calibration off of (partially).

I'm not sure how to tackle the problem of different build ups & recipes. Is the WOT fuel knob a solution? Maybe. It may end up to be worthless. It may end up to be just a fine tuning aid. It may end up to be a knob used as a boost controller. I'm not sure yet, but I like the potential it has.

I'm not sure a fuel knob will be the end-all
solution, either. Is it better than nothing?
Sure. It scares me, to tell you the honest
truth. Tuning needs to be done in small steps,
big ones usually end up costing big $$$.

Boost controller seems more viable, to me.
Either that, or use it to control a WI pump.

The chip is closer to being ready, but still not yet. How long? I don't know. It's been too long already. Unfortunately, tuning goes slow. I made a *lot* of progress on my truck, but the WOT stuff has to be done on trucks that people will copy the builds of.

And even that seems to be a bit of a crap
shoot, since nobody ever follows the same
exact recipe, 100%.

A WB o2 and an Emulator makes pretty quick
work of the WOT tuning part. An hour driving
around gets things close in a hurry.

If you don't have the truck, it's a tough
thing. 8" of snow is also a PITA.

Later,

Dig
 

turbodig

Active member
On 2001-10-30 10:50, Red Canyonero wrote:
The linearity issue is why I chose the 50s, this has been apparent for years. The 009s are a pain to deal with. The calibration I had running for my Ty with the 50s was better than how it ran with stock injectors. Yes the 50s are expensive compared to 009s, but time is precious, and I've already spent loads of time on the 50s, let alone what would be needed on the 009s.

The 009s are coming along. We really don't
have the hours behind 'em that y'all do with
the 50s, but we're getting there.

I really don't see much linearity difference
in the 009s vs. the 50s. I'd say neither are
linear, and their curve is a bit different,
but not dramatic. You can re-scale a 50# chip
for 009s, and it runs fairly ok. Surprisingly,
I'd even say.

I've heard reference to problems with the 50s
and open/close times. An injector that big
really needs to be peak and hold to get the
thing to deliver accurately, especially in
transitional situtations.

This is from a perfectionist viewpoint, not
to say the 50s won't/don't work. It's obvious
they do, but the speed issue could explain
some of the demons we fight in tuning these
things.

Later,

Dig
 

kwick6

Donating Member
The different builds can really complicate tuning for a *generic* chip. I think everyone should just upgrade from stock to a te44, and leave all the rest stock. :grin: If they start changing heads, cam, etc. then they will need a custom chip, or speedpro.

Fwiw, a possible solution would be that anyone who is interested in running chips is best off considering getting a burner and a *zif* socket (sp?) That would allow someone to supply a generic chip specific to a simple upgrade like a te44 and 50lb injectors, similar to Opie's truck. Then changes could be sent via email and the person could burn them to his or her chip and then the chip could go right back in.
I am considering this because I am one who desires to get my truck tuned to the best possible. That would make for a good package deal as well, a burner, zif socket, and the initial program. It is just a thought, and I am positive I don't want any part of sending chips back and forth through the mail for editing to be done. It is just way to drawn out, and too much down time. Not to mention the person having to do the changes, it would not be too fun for them to have to deal with a bunch of chips going in and out all the time.


I'm not saying that BG should have to work with every single truck. It might give the buyer the ability for easy adjustments to be made, and the success of a general build could start to come together.

I hear so many people say "I wanna do this and that and once I do it I'm done" That just starts a chain reaction of rebuilding the motor, blablabla.
I have spent a ton of money, since I bought my truck....its time to mellow out now...and I really like the progress that BG has made with this setup, and when Opie's truck is dialed in and running smooth I will probably go for it. I just can't spend anymore on it. Not for a long time. I have been doing so many changes to this or that on my truck since I bought it....it hasn't been in one successful setup, where I've been happy and just said this is running great...I'm going to leave it alone.
Please give feedback, I think this should be addressed as it would greatly enhance the performance of any chip, build.
Sorry, but I am anxious to find a stopping point in this all out syty madness. :grin:

Thanks,
Scott
 
Top