4" down pipe

qbnkiller

qbnkiller

Conflaguration Specialist
Re: 4" down pipe

I do. Outside pass frame rail between cladding and frame. Round Dynomax muffler under there too. Stops in front of rear tire. Pics somewhere. I am still waiting for my cladding to melt like I was told would happen two years ago.
 
gt67sy

gt67sy

Member
Re: 4" down pipe

I know Frank (autoaddictons) had one inside the frame rail it can be done, but it's a very very tight squeeze
 
TYTILIDIE

TYTILIDIE

METH HEAD
Re: 4" down pipe

qbnkiller said:
I do. Outside pass frame rail between cladding and frame. Round Dynomax muffler under there too. Stops in front of rear tire. Pics somewhere. I am still waiting for my cladding to melt like I was told would happen two years ago.
Click to expand...

Hm, from what I can see the tire will hit when turning.
 
TYTILIDIE

TYTILIDIE

METH HEAD
Re: 4" down pipe

gt67sy said:
I know Frank (autoaddictons) had one inside the frame rail it can be done, but it's a very very tight squeeze
Click to expand...

I think thats the route I am going to go.

I gave serious thought to a hole in the fender. I am going to run a 4" electric dump anyway I go and divert through the 3" so the noise and smell would only be irritating when open but going to try between frame and engine/trans first.
 
mattw

mattw

Active member
Re: 4" down pipe

I did it inside the frame on my 4-door... Good luck!

IMG_2576.JPG
 
Sy-1177

Sy-1177

Turbo Inside
Re: 4" down pipe

My TT Jimmy has 2- 3" dp's that merge into a 4" right under the passenger seat and go 4" out the back to rear corner. fits good from what I can tell
 
Black Knight

Black Knight

I Glow Therefore I am
Re: 4" down pipe

Eviltwin runs a 4" all the way back inside the frame, IIRC he was even able to do it with the A/C box in.

I'm sure there are pics in his thread or you can message him.
 
gt67sy

gt67sy

Member
Re: 4" down pipe

I to have give serious thought to out the fender but I've really like Jaime hacking truck where it goes out the bottom of the front half of the fender but don't know if it could be done with a turbo mounted near the stock location as his is mounted in the front down low in the center of the bumper.
 
eviltwin

eviltwin

"junkyard syclone"
Re: 4" down pipe

Black Knight said:
Eviltwin runs a 4" all the way back inside the frame, IIRC he was even able to do it with the A/C box in.

I'm sure there are pics in his thread or you can message him.
Click to expand...

It is an easy fit.

I have done a 4" with stock unmodded a/c box and a modded inner fender. Right now I have a 4" with modded non a/c heater and unmodded inner fender.
 
TYTILIDIE

TYTILIDIE

METH HEAD
Re: 4" down pipe

Got it Paul, sorry I haven't replied. I need to wait til I get my oil pan done and finalize my install. I am toying with building new ALT/PWRSTR brackets altogether, it will depend and how bad the 's need to be modified to fit my CS144. I'll let you know within a month or two for sure.
 
Z SKI

Z SKI

Donating Member
Re: 4" down pipe

TYTILIDIE said:
Got it Paul, sorry I haven't replied. I need to wait til I get my oil pan done and finalize my install. I am toying with building new ALT/PWRSTR brackets altogether, it will depend and how bad the 's need to be modified to fit my CS144. I'll let you know within a month or two for sure.
Click to expand...

Cool beans... Let me know... Good luck with the build... Looking great so far!!
 
It's just a six

It's just a six

Super Member
Re: 4" down pipe

Black Knight said:
They are in the build thread, you know the one where all you did was consistently talk shit about everything he did. :tup:
Click to expand...

I think you need to re-read my suggestions in the thread then.

Also, if you re-read it, you can clearly see who starts talking smack.
 
You must log in or register to reply here.
Top