aftermarket chip testing

syclone3

Member
Finally had a chance to test some chips on my beater Syclone on my Mustang AWD dyno.
Tested
4053
4175
KB piggyback with both 4053 and 4175
Hypertech piggyback with both 4053 and 4175
1991 ATR pitbull
1993 ATR pitbull

Wish I had an ATR stripchip.

Truck is as follows.
66,500 mile original engine
rebuilt stock trans, done before I got it. I did put valvebody kit in. Since old lady that had it, requested the trans be "toned down" when rebuilt.
ATR trans cooler
Ultra flow straight through 2.5 inch mufflers, yes it still has stock appearing twins.
2.5 inch testpipe
2.5 inch mandrel DP, heat wrapped, crossover is also.
KB FP regulator
255 Walbro
ATR cool air box
Magnecor wires, stock plugs
Atwater IC pump running all the time
Fan on back of heat exchanger
ATR aux cooler
manual controller after stock solenoid before WG canister
EGR blockoff plate.
Acell coil. Had it sitting around.
100 octane Rocket Brand unleaded, little C16 out of my race car, maybe 3 gallons to 17 of 100.
160 stat, stock fan.
J&S knock retard system, KB version. Not all wired up yet and functional.

Results were interesting. Made 16 runs today. Sure learned alot.

Do have a stock injector old style KB shootout chip. Might try it with all C16 or higher gas and the J&S functioning. I know on my other truck this chip picked up a whole lot at the track on some 120 fuel I had.

Will combine the two ATR and the one KB chip, best run of each, into one dyno graph and figure out how to post it up on here.

Lot of what I learned today will be helpful making a custom chip for this setup. Whats in there right now is pretty close to being perfect. Just shows that it takes many different chips to find one that is on the right track. Then making the best program with Code59 or such will perfect it.

I have an HKS standard gate on a stock crossover pipe thats 2000 degree coated. Might put it on tomorrow once I make a bracket to hold the stock gate shut. Not sure if the boost will be much better or flatter. But the difference in backpressure could help the stock turbo.

Power right now is 311 and torque is 459. Done in 3rd gear, not locked up. 20-21 psi dropping to 17 range.
 

Beavis

Still plays with trucks
Re: aftermarket chip testing

Be very carefull as some of those chips won't pull timing if it detonates. The last thing you want to do is pop amotor while testing chips for fun. Also let us know whick ones do and do not pull timing, add timing and add boost (if any) and eliminate the overboost protection. And if poss please test each one seperate before combining different combos. This is always something I have wondered about but never had time, place, and resorces to do it. This should be interesting. :) Also try them with different octane's too and the results with them.
 

syclone3

Member
Re: aftermarket chip testing

Thats why I had a lot of octane in the tank, ice bags on the intake and intercooler and a lot of fans blowing on the heat exchangers. I don't plan to run the chips in the truck with pump gas as its 91 out here and would be afraid of the gas on an all stock truck. The least the truck has seen since getting this one is 100 unleaded. The station next to my shop sells it for $6 a gallon. As little as I drive it, well worth it.

The Hypertech piggyback chip had the best air fuel. A flat 11.3. Want to use that fuel table as a starting point when I make a new chip. All of the others came in lean then started to richen up. The one ATR was WAY lean period. The other was around 12.3 I believe.

Hypertech was pretty tame on timing. Evidenced by the lowe power and torque. Zero knock retard. Both ATR's had some timing but as fast they put it in, it seems to be taken out in the chip. Saw very little knock retard on my scan tool. But power really drops off up top on both of them. One more than the other.

The old KB piggyback had the best timing by far. Power too. I am just glad I got all the dyno runs and graphs with the data now to choose from. Plus it helps me where to look for piecing together the new chip. Instead of starting with a stock BIN and spending a lot of time on it. Can speed up the process with less wear and tear on the truck.

Yesterday I put the HKS external and crossover on the truck. Unfortunately found the source of a coolant drip since I got the truck. The inner coolant line from the turbo to engine. See if I got that sealed up or not today. Then bolt everything else up.

Sure will be nice to have a flat boost curve. Once the boost is dialed back in to where it was before will make some dyno runs probably this week.

Also changed the plugs. The AC CR42's looked good and clean after all the dyno runs. No sign of detonation. Put in some NGK U-grooves. Back in 1993 I used to run Acell U-groove 276's. Worked well. Then Jim Stokes told me to run the stock plugs as nothing was better. Today so many rave about the NGK's. And I run them in all my Mitsubishi motors, bikes.
 
Last edited:
Top