Bad Mileage + Sluggish Performance = ???

Dr.Evil

Addicted to Boost
Re: Bad Mileage + Sluggish Performance = ???

Alright I got the adjustable FPR installed and set the pressure at 38 PSI Idle. It fires right up, idles fine and then all of a sudden it will sputter and die randomly. It does not drive very well. I am getting 18 for vaccum at idle. Is this alright?

Also, now that the FPR is installed, the injectors or FPR is making some strange high-pitch noise (kind of sounds like a spark arcing). I took a quick video clip of it. You have to listen closely to hear it.

Video Clip

If I snap the throttle It backfires. Something still isn't right here. Good news is it doesn't bleed off the pressure anymore and fires right up with only one or two cranks. Now I just need to get it driving well. Any ideas?

Anyone have a clip of the coolant flow with the cap off in the upper intercooler? When I have the pump on I can't even see it circulating. The upper line is the return and has been converted to heater hose running across the engine bay and down through the driver side fender. Mabye the line is too long for it to flow well?
 

dgoodhue

BuSTeD 4.3
Re: Bad Mileage + Sluggish Performance = ???

I get between 20 and 22" of Hg. Are your vacuum line original?
 

Dr.Evil

Addicted to Boost
Re: Bad Mileage + Sluggish Performance = ???

yes they are original.

Does anyone make a replacement kit possiably out of sillicone?

I got the 18" measurement with my aftermarket vac/boost guage so it may not be 100% accurate.
 

Dr.Evil

Addicted to Boost
Re: Bad Mileage + Sluggish Performance = ???

Alright so far I have replaced the following with no luck:

Plugs
Wires
Cap
Rotor
Coil
Catalitic Converter
Catback
Air Cleaner
ECT sensor
Thermostat
FPR (installed adjustable unit and set to 42 PSI idle)
ACT sensor
Ran a can of injector cleaner through and always use 91 octane Chevron gas

What's next? Possiably injectors? I have to be getting close as I am running out of things to replace. :roll:
 

SY2455

70's Veteran
Re: Bad Mileage + Sluggish Performance = ???

Replace all of your vacuum lines like (dgoodhue said) if they are original. Some time they will look ok but have a crack on the bottom side that you can't see & it will effect your performance under boost because the crack will grow under boost.
 

Dr.Evil

Addicted to Boost
Re: Bad Mileage + Sluggish Performance = ???

I replaced all of the soft vac line for starters. I am getting 15-17" Hg at idle.

I also checked the compression, and it is great across the board.

I noticed something tonight that got me thinking...I never really looked at the tach when giving it WOT. Anyway I saw tonight that the 1-2 shift is at 4200 and the 2-3 shift is around 3900-4000 in drive under WOT. whats the deal with that? This makes me think that it is a vaccum problem.

Also, for some reason it is running even worse with the new FPR set to 42 PSI. It won't idle when cold. To top it off I raced a stock VR6 older jetta from a light and LOST! man this thing is really not running right and I am getting tired of trying to find out what it is.

Anyone view the video above and have some comments on the sound? It only started doing that with the new FPR.
 

bezerk

New member
Re: Bad Mileage + Sluggish Performance = ???

i listened to your video..
don''t hear it backfire
 

bezerk

New member
Re: Bad Mileage + Sluggish Performance = ???

and are you going WOT, without datamaster, and with a crappy tune?

Don''t do that, or else you''ll be pissed even more.
what chip do you have annyway?
 

dgoodhue

BuSTeD 4.3
Re: Bad Mileage + Sluggish Performance = ???

Dr.Evil said:
I replaced all of the soft vac line for starters. I am getting 15-17" Hg at idle.

If you have a stock cam or even a moderate cam 15-17" is not enough vacuum at idle. You have a vacuum leak somewhere. I would double check you vacuum lines. It could be a injector no seated properly, intake manifold leak, leaky check valve, etc. I would even go through the hassle of blocking off vacuum source.
 

Dr.Evil

Addicted to Boost
Re: Bad Mileage + Sluggish Performance = ???

Alright I just replaced every vac line I could get my hands on. Including all of the hard lines, "T", elbows, etc with sillicone vac line. That got my vac down to around 16".

Next I checked the timing. With the tan/black wire disconnected, the mark was way off. Being that it is driven at high altitude daily (4500-5000) I set the timing to 8* advanced. Is this okay? I do not hear any pinging at all. Vac at idle is down to 18" now in neutral.

One thing I noticed that I can't figure out is with a vac line completly disconnected and the truck running, it runs the same as when its connected...? Also, the line that goes down to the charchol canister does not have any vac going to it. I think maybe that port on the intake is clogged?

The truck runs much better now, but still not 100% I don't think. It also still shifts early. I tried a run manualy shifting it, and it seems to be cutting out between 4600-4900 RPM. Also, in 2nd and 3rd gear I am only making 12 PSI of boost. I did have 15 before I changed the lines and set the timing.

How do I adjust the shift points on this thing? Any other ideas?
 

dgoodhue

BuSTeD 4.3
Re: Bad Mileage + Sluggish Performance = ???

8 Degrees advanced is not alright, assuming the balancer is correct and hasn't slipped. You should do a TDC check to verify the balancer mark.

The vacuum port for the charcol carnister is a poor vacuum source, so probably would affect the idle quality. That vacuum source is in the same passage as the IAC and the IAC may have compensated for it anyways. (IAC is essentially a controlled vacuum leak)

If you have the stock chip, it should cutout at 4800 rpm and fall back to 4600rpm. I think your are confusing short shifting comapred tach warning and redline. My Truck shifts at 4400 1-2 and 4600 2-3 and from my experience my truck shifters higher than many, I have been in few Ty's that shift 1-2 4000 and 2-3 4300 rpm and they still run great ET's. On a stock heads/cam truck, you do not need to rev any higher. Infact teh low rpm help hold together the fragile lower end of the truck. If you were to put just a cam and chip that allow the stock engine internals to rev and make power to 5500 rpm, it would greatly reduce the life span of the motor.
 

Dr.Evil

Addicted to Boost
Re: Bad Mileage + Sluggish Performance = ???

Alright I set the timing to 0 and verified TDC. The ballancer is right on.

There is no chip in it right now. I have a hypertech and a ultimate for it, but am not using them until it is running right.

I need more ideas guys. I don't want to just keep throwing parts at it. I am dying to get this thing running right and am out of ideas.

Recap of what I have done:

set timing properly
replaced entire ignition system
checked and comfirmed good compression
replaced all vac lines and am now getting 18" Hg at idle
set adjustable FPR to 42 idle PSI
Replaced cat w/ high-flow unit, exhaust dumps shortly after that
New O2, ECT, ACT, Thermostat
verified turbo has no shaft play and I am getting 15 PSI

How much does good IC coolant flow affect performance? Can you noticably tell a difference with the IC pump on and off? I do not think I am getting good coolant flow even with my new high-flow pump. Could this cause a big loss in power?

Any other ideas would be great. I am going to be messing with it again on sunday and need some input. Thanks in advance!
 

SeattleSy#1255

Category 5 Conservative
Re: Bad Mileage + Sluggish Performance = ???

what about you ECM? Do you have another you can throw on to just see if anything changes?

didn't read anywhere what injecters you are using with the stock chip?

have you verified you have a 2 bar MAP Sensor in there with your stock chip?

Ultimate is 3bar if you throw that on, it'll run like crap without a 3bar Map Sensor, just a FYI.

i'm assuming your wires aren't crossed in anyway (plug wires).

what plugs exactly are you using?

timing: you used the mark furtherest to the left when looking down from the front correct?

do you have a datamaster file?

are you maintaining FP? Does FP rise with boost and hold or drop? Is your fuel pump stock, dying?

what happens when timing and you leave the tan wire unplugged...how does it run then? does it suddenly want to die after you plug the tan wire in?

what does "replace entire ignition system" mean...what is entire?
 

timgt

UR2SLOW
Re: Bad Mileage + Sluggish Performance = ???

I read that your FP is dropping off when you cut the truck off, this is NOT supposed to happen. I had the same thing happen and it took me FOREVER to realize this was coming from inside of my fuel tank. A previous owner had been inside the tank and when they removed that resonator thing (can't remember the name) they put a small rubber piece in like they were suppost to BUT the clamps holding that rubber piece was loose. I tightened the clamps and now I don't lose fuel pressure.

There are some tests you can do by crimping the rubber part of the fuel lines under the truck to see where the pressure is bleeding off.
 

Dr.Evil

Addicted to Boost
Re: Bad Mileage + Sluggish Performance = ???

SeattleSy#1255 said:
what about you ECM? Do you have another you can throw on to just see if anything changes?

didn't read anywhere what injecters you are using with the stock chip?

have you verified you have a 2 bar MAP Sensor in there with your stock chip?

Ultimate is 3bar if you throw that on, it'll run like crap without a 3bar Map Sensor, just a FYI.

i'm assuming your wires aren't crossed in anyway (plug wires).

what plugs exactly are you using?

timing: you used the mark furtherest to the left when looking down from the front correct?

do you have a datamaster file?

are you maintaining FP? Does FP rise with boost and hold or drop? Is your fuel pump stock, dying?

what happens when timing and you leave the tan wire unplugged...how does it run then? does it suddenly want to die after you plug the tan wire in?

what does "replace entire ignition system" mean...what is entire?


I unfortunatly do not have anther ECM.

I have the stock injectors in there with the stock chip. They look old, the truck has 106K on it, should these be replaced?

I made sure the stock 2-bar MAP is in there.

With the ultimate chip, it runs the same with or without a 3 bar MAP, which is like crap.

I triple-checked proper plug wire routing and correct cylendar.

I have the NGK UR5 plugs in there now. (I think that is what they are called, its what everyone recommends here on the forum)

"timing: you used the mark furtherest to the left when looking down from the front correct?" On my timing mark, it says that is 8* Retarted. I thouht 0* as the little notch on the right after the three big ">" marks...?

I do not have datamaster yet. I will hopefully by the end of next week.

Fuel pressure is not dropping off anymore with the AFPR I put in. I don't know if it is raising under boost because I do not have an in-cab fuel press guage. Should it? Fuel pump is stock as far as I know, however it sounds good.

I set the timing with the tan wire unplugged. The CE light comes on with it unplugged. What should the difference in timing be with it plugged in VS disconnected?

I replaced Plugs, Wires, Cap, Rotor, and Coil.

Anyone view the file above and hear the noise I am describing? Not a backfire, more like an electrical short sound comming from the FPR and injectors....
 

93ty475

Donating Member
Re: Bad Mileage + Sluggish Performance = ???

Dr.Evil said:
"timing: you used the mark furtherest to the left when looking down from the front correct?" On my timing mark, it says that is 8* Retarted. I thouht 0* as the little notch on the right after the three big ">" marks...?

balancer marks is what he means....there are two lines on the balancer.....also might help to mark the balancer and tab with a white paint marker....


Dr.Evil said:
Anyone view the file above and hear the noise I am describing? Not a backfire, more like an electrical short sound comming from the FPR and injectors....

that's normal....


if you really think the noise is coming from an electrical short, turn off all sources of light and look under the hood while it's running, in the dark....that sound file wasn't the best and was rather short....kinda hard to tell anything from that....swapping 3bar to 2bar sensors should make the truck run like crap....if i were you, i'd disable the fuel pump, then remove one sparkplug at a time, put your finger over the plug hole and verify that each is plug is sparking around the same time that the cylinder blows the compression by your finger....firing order on these trucks can play tricks on your mind at times......datamaster should help and is a must, but there are many basic things that datamaster won't report....good luck
 

Dr.Evil

Addicted to Boost
Re: Bad Mileage + Sluggish Performance = ???

93ty475 said:
balancer marks is what he means....there are two lines on the balancer.....also might help to mark the balancer and tab with a white paint marker....




that's normal....


if you really think the noise is coming from an electrical short, turn off all sources of light and look under the hood while it's running, in the dark....that sound file wasn't the best and was rather short....kinda hard to tell anything from that....swapping 3bar to 2bar sensors should make the truck run like crap....if i were you, i'd disable the fuel pump, then remove one sparkplug at a time, put your finger over the plug hole and verify that each is plug is sparking around the same time that the cylinder blows the compression by your finger....firing order on these trucks can play tricks on your mind at times......datamaster should help and is a must, but there are many basic things that datamaster won't report....good luck


I know it is not an actual electric short, thats just the best way I could think of describing the sound.

Anyway I just got done cleaning the whole intake, port matching the upper intake, replaced the injectors with accel 30# units, cleaned the upper IC, re-routed all IC lines and sealed everything up with new gaskets. I have not fired it up yet. I hope it will run better now. I actually found that part of the upper to lower intake gasket was missing, probably causing a pretty bad vac leak.

If this does not work, what else is left? Not much on the outside of the motor.
 

93ty475

Donating Member
Re: Bad Mileage + Sluggish Performance = ???

Dr.Evil said:
. I actually found that part of the upper to lower intake gasket was missing, probably causing a pretty bad vac leak.


i would say that missing a piece of your intake gasket would cause it to run like total crap.....some people won't go into them that far....i would leave the stock injectors in there for "ruling out" purposes....you can change them without removing the upper, if you're careful not to bend the rail (like i've done)......my bet is that it's going to run perfect now....
 

dgoodhue

BuSTeD 4.3
Re: Bad Mileage + Sluggish Performance = ???

I can speak from experince, the leaking intake gasket is going to make a big difference.

Hopefully that is the last of your problems :friends:
 
Last edited:

Dr.Evil

Addicted to Boost
Re: Bad Mileage + Sluggish Performance = ???

well I couldn't work on it this weekend, I got back on it today. I still have to hook up a couple things so I didn't take it for a drive, but it fired right up. I mean I just touched the starter and it fired, unlike the usual 5 or 6 cranks of the motor before firing. so thats a good sign. I also found out that the IC system was/is doing nothing so that will def help out also. its almost there!!!
 
Top