Beginning mods question

typhoon1588

New member
Right now she's all stock and slower than a Hummer full of fat kids. I was thinking of starting off with these things:

Walbro 255 ltr/hr Fuel Pump
Kenne Bell Adjustable Fuel Pressure Regulator
STG Ultimate Chip
ATR 160° Thermostat

I am not sure if there is anything better/else to start off with. I would also appreciate a hand in where to get the best price for these things. Does anyone have any suggestions?
 

Phoon30

New member
As far as the t-stat goes, I think you'd save a little money if ya didn't get the ATR. Just hit up pep boys or auto zone and pick up a Mr. Gasket part #4363.
 

AXXE

Member
You need a data logging tool of some sort. Any exhaust with very low back pressure and some sort of cold air kit. I have the ATR but think that something better can be made once you relocate the battery.
 

typhoon1588

New member
On 2002-03-12 16:44, SY732 wrote:
1st thing I would get is diacom or datamaster

see
http://syty.net/faq.htm

I am very interested. I have the laptop, but I seriously have NO idea where to get the Datamaster software or cable. Unless I can get some pointers on where to find them, I will just wait to run it with Mike B.

AXXE, the ATR Cold Air Kit and exhaust are definitely on my list, how important are these things early on?
 

AXXE

Member
I am still relatively early on myself. The exhaust, intake, and I/C pump took about .7 second off my ET. You dont need any expensive exhaust. I have a straight through 3in Dynomax with 3in cat back. Look into another way to relocate the battery. I really dont like the ATR kit. It is too hard to get to the battery. Once the battery is out there is a lot of room to make an intake setup.
 

Tooky

Serious about performance
I would do the following order, given what you've suggested:

#1. DataMaster, so you can see what the effect/gain is for each thing as you do it going down this list. Among other obvious reasons to get it!!
#2. Walbro 255 LTR/HR High Pressure fuel pump. There is a "normal pressure" version, spend the extra $10 or whatever and get the High Pressure one!
#3. AFPR - I'd do this the same time as the Walbro.
#4. 160* thermostat. Cheap and easy. I used the gold heavy-duty-looking "Robinson" one from AutoZone for $4.99 and it works like a miracle, I don't know if I just got lucky or what but no matter what the temperature or how many passes I've made at the drag strip, it ALWAYS stays within 3* of 160*F! I would really be interested in hearing how your before/after Datamaster runs compare with this mod. I have heard talk that it can reduce knock but can't remember any specific people who had hard data.
#5. Tune the truck until the knock is very very low. I would say no sustained knock over 3.5*! Some have said a limit of 5.0 but that makes me uneasy so I will say 3.5*. I feel this is a very critical step before proceeding to the next (ultimate chip)!!! This step alone might take the rest of your season to accomplish, fair warning!
#6. Ultimate Chip and 3-Bar MAP sensor.

Also there is some stuff you could throw in at any time after #1. Like hotwiring the IC pump (no reason not to do it), replacing the stock IC pump with the Jabsco, adding an auxiliary IC radiator, etc.

Hope these ideas help!
 

ParTyBoy

New member
On 2002-03-12 17:35, typhoon1588 wrote:
On 2002-03-12 16:44, SY732 wrote:
1st thing I would get is diacom or datamaster

see
http://syty.net/faq.htm

I am very interested. I have the laptop, but I seriously have NO idea where to get the Datamaster software or cable. Unless I can get some pointers on where to find them, I will just wait to run it with Mike B.

AXXE, the ATR Cold Air Kit and exhaust are definitely on my list, how important are these things early on?

Personally I would skip the ATR kit... Unless you're not driving the Ty a lot, a battery relocation kit sucks period... If/when you decide you need to move the battery either use something like the Kenne Bell kit (even though some have had probs with what they supply) or something like Keiths idea...

As far as steps you need to take... check out
the list at: http://www.georgiasyty.com/mods.htm
Should be used as a base guide to give you some ideas on a good approach to upgrade..

and Tooky's post is right on the mark...
(No favortism here Daron.. or Tooky... Just I agree with what's said) Datamaster's a good way to start... Need to get around to finally grabbing a logger tool and crappy portable myself.. kind of preoccupied with restoring my truck first though before I race it... Hope this helps..

<font size=-1>[ This Message was edited by: cHoCco on 2002-03-13 10:52 ]</font>
 
Top