Blitz Controller Question...

Windedv6

Ty n 10s
I am using the SBC id Blitz controler and have been playing around with it in both manual and auto modes.

In auto mode I can get it to match my boost guage almost exactly, but my spoolup lags big time. I have tried the gains at 15, 25, 50, 75 etc and it doesn't make much difference. Running at 24 lbs of boost it holds steady once it gets there, but doesn't get there until third gear. Slow climb from about 19 to 24lb.

In manual mode it uses guess work so I get my 24lbs at about 37% and my spool is better. It doesn't spool as good as my bleeder regulator, which was almost instant. Also under manual mode will the blitz controler still have the capibility of the warning, buzzer and boost rollback for over-boost or is that only on the auto mode setting.

I was hoping to run on the auto mode setting for safty measures and to take some guesswork out of making the changes needed for outside air temps, etc.


I have a pte 70 steath turbo with the internal wastegate using an actuator. I tried to run the Blitz on wastegate mode and everything went nuts. Big swings in boost.

What has been the experience with these and am I missing something on setting it up correctly?

I read through the threads via the search and didn't really find a clear answer.

TIA

John
 

100in6

100in6
i may be all wet on this, but i seem to remember that when i bought and used my blitz sbc id that it wasn't supposed to work on auto. I'm almost positive that's what they told me. only manual on ours. les
 

myclone

Donating Member
100in6 said:
i may be all wet on this, but i seem to remember that when i bought and used my blitz sbc id that it wasn't supposed to work on auto. I'm almost positive that's what they told me. only manual on ours. les

Ditto here too... Mine has never been out of manual mode.
 

Windedv6

Ty n 10s
I wiil work on the manual route. Interesting though that on my setup wherever I dial the boost 19, 20, 22, etc it stays right on. But the spool up sucks. I know Les is runing an external wg. What are you running myclone? and where do you end up on the gain control.

Also does the warning and limlt work on the manual mode?

John
 

100in6

100in6
john

i never ran the blitz on the sy you know. i had it on the other one. with the integral and the pt52. run it on manual and set the gain and you should have really good control. mine spooled up well and was pretty rock solid on manual

lets go tomorrow to norwalk

call me I'll be up till well past midnight my time

les
 

Windedv6

Ty n 10s
I have to work till noon.....do a few test runs on the street. Depends on how late it gets cause Norwalk is in the eastern time zone. When do the gates open?? Is it test and tune nite? How many runs can we get in. I have a track a little over an hour away vs 3 hr to Norwalk....but I'll see what i can do.

When are you leaving for BG?

John
 

100in6

100in6
sent you an email, did you get it? leaviln for bg about 6am on friday unless plans change.

give me a call
 

myclone

Donating Member
Im running an external ITS Pro Gate. Spool up seems fine to me but Ive got that tiny T3 turbine housing and a 3k 9/11 so that prolly takes care of any spool issues.

None of the alarms or warnings work in manual on mine (least Ive never heard or seen any :-? ).
 

myclone

Donating Member
Forgot to add that my gain is up around 50.. When I first tried the boost control out spool up was a little slow compared to the HKS EVC that I had even with the above mentioned TC/turbine housing but after speaking with the person I bought the boost control from they said not to be affraid of cranking the gain up (it was set at like 25ish from the factory) so I started increasing it till spool up got better. Eventually spool up was good IMO so I left the gain alone and havent touched it since.

If/when the employment issues are settled with me then I plan on going a different route with turbo, WG, and controller so Im prolly not gonna mess with the Blitz much longer (FWIW, its worked flawless for me but doesnt have some features I need).

BTW, If you need to know exactly what my gain is set at lemme know and I'll look tomorrow when I get home.
 
Top