Boost control again

AXXE

Member
Every few weeks I am posting about the problem I have building boost. If I set the Ultimate to 17 or 18 psi it only make about 15 psi in 1st and 2nd gear. I was told that my WG spring might be weak. Yesterday I unplugged the boost seleniod to check base boost. My WG rod is very tight, only 3 threads left. It made 15 psi in 1st and I let off. Same in 2nd. Does this mean my WG spring is in good shape? Did I check it correctly?
 

TheObiJuan

Active member
ah..
why not just get an external.
and if you want variable boost, get a manual boost controller with the external?
ed hess has a set of dual externals on a crossover pipe for sale
 

AXXE

Member
I thought about going external with a different turbo eventually. For now I would just like to straighten out this problem. The truck runs good. I just need to know it is going to do what it is supposed to every time.
 

Mad Mike

SYCOSIS
Do you have a scan tool to see if you are getting knock? Is datamaster /diacom showing how much boost your getting? Don't go by a guage. Start with the stock chip and 2 bar first. Once it is straightened out then add the ultimate.
 

AXXE

Member
I've been playing with this for a long time. DM shows no knock on T1-18 and boost is still bad. Rarely do I see 18psi in 1st. Second will go to 18 sometimes but then it comes right down. It killed my times at Atco on the 15th. When I had just the stock chip it used to spike to 17psi and shut off. I am thinking about a separate boost controller. Any suggestions?
 

kwick6

Donating Member
boostvalve.com

works great, spool up is much better and control is rock solid. Although I don't have stock turbo.....


The stock setup creates lots of backpressure.

Boost control is a PITA, if you want the best advice, get the external and be done with it, or you'll be screwing around having problems when you could be tuning other areas. I think bdubb has some dyno numbers that reflect what just an external added to a stock truck.

The stock wastegate is a poor design, and you will never get rock solid boost with it.


HTH

Scott
 

ed hess

race or get outta the way
mark
ya know the valley on the boost curve in dm you see in 3rd gear after it has shifted and started to rise again then it drops and startes to rise again and there isnt any reasson for it (i.e. no knock), well, You make me an offer and those spikes and valley's will disapear. You see that vallley on all dm files for stock turbos with stock wastegate i have seen.

so make me an offer and its yours.

ed

btw these things look really cool to!
 

ghettosled

SYTY SUPERSTORE
have you verified timing with a tdc check? sounds like your wg rod is very tight if you are making 15psi in 1st gear w/ the selenoid unplugged.. Should be around 8-9psi.

sounds like you have another issue besides the chip.
 

Raist103

Engine Killer, iPhone Killer, Lawnmower Killer
boostvalve.com

works great, spool up is much better and control is rock solid. Although I don't have stock turbo.....

how does this work with a aftermarket turbo?
and do they have a kit for our ty's?
 

Tooky

Serious about performance
Raist103 said:
boostvalve.com

works great, spool up is much better and control is rock solid. Although I don't have stock turbo.....

how does this work with a aftermarket turbo?
and do they have a kit for our ty's?

I got the Universal kit. It's just a air pressure valve. It would work on any turbocharger with a wastegate actuator. I borrowed it off my Syclone and put it on my Turbo Grand Prix and it works absolutely incredible on there.

You simply connect the "straight" end of the valve to the line coming from the turbo compressor. Then the "Side port" of the valve connects to a line going to the wastegate actuator. Start with the valve very loose and slowly tighten it 1 turn at a time as you continue testing where the boost is. But watch out, you can easily destroy your motor if you turn the boost up too high and the ECM will be helpless against it. (Well it can retard timing but not lower boost anymore.)

FWIW I have the stock turbo and the boostvalve offers the best control of any option I've tried so far. But it's still not perfect and it's still somewhat dangerous.. I'm gonna end up switching turbos because the only real safe option for boost control on the stock turbo , is an external wastegate which I will not consider.
 

Sy769

Donating Member
I am using the Granger valve setup. very cheap and I see 1.5-2psi spike initially then it is much more stable than the stock setup and you don't have to worry about the first run boost limit at the track. I will be using a external at some point.

As a side note my brakes hold very well--I did a 15psi launch for the first time the other day. That kicked a$$ :D Left a little BFG on the pavement.
 

QWERTYphoon

Motley Driver Award 2009
Re: Boost control again

I am installing a variable boost controller. Does this mean you by-pass the solenoid? I guess the instructions I have don't explain this! I am only able to get 9 psi at WOT w/ stock turbo. I am hoping to increase that with a VBC. The truck does not want to shift into third @ WOT. Any Ideas?
 
Top