BS3 Qs newbie.

denny

Active member
I have BS3 install and its runnig OK, but I still need to understand some things before I start trying to tune it.
I couldn't find much info on the net, I tried the theturboforums.com. I am not a racer, I go to the track maybe once a year, so I don't want to pay to get it tuned.
* Thanks autoaddiction for the start up file.

Here some my questions.

1. My stock ECM show 100% TPS when the pedal depress all the way, now on the BS3, it shows 80%. Do I have to adjust the TPS sensor to %100 TPS or some paramater change on BS3?

2. I don't understand what these do or if I need need.
Crank Trigger
Static test timing
COP - coil on plug
Frank is using 'Override Cam Sync test' , this don't work for me. Missing , like the timing is way off.


3. What do you tune? Say it runing good driveability wise, now tuning would be
Timing
Fuel
AFR
Since my system don't have any ESC - knock retard. What do I look at to know if the tune is getting good or bad?

Thanks
Denny
 
Last edited:

skipztt

boost
Re: BS3 Qs newbie.

maybe adjust the tps sensor a little and see what happens? :dunno:

also i would say keep messing with the timing and watch ur AFR. when it starts to knock alittle you know ur close to going as far as you can. but i have never tuned yet. im just throwing out some ideas.

so just wait till some of the big timers come and chime in :tup:
 

10secTy

Sy-Ty builder and Tuner
Re: BS3 Qs newbie.

Did you read the manual that comes with the BS3? Alot of this is covered in it.

#1 what is your idle tps %? You need to set this about 2 higher than what you see at idle.
It looks like it is 2 so set it at 4
Do not worry that it does not go to 100% its not important like on a stock ecm.

#2 for HEI you set the crank rev at 6 degrees. This means your dist will be at 6 degrees.
You can check this to make sure you dist is set properly by using the static timing.
put 20 in the box and check the box. This will lock the timing at 20 then pull out your timing light and make sure you have 20. If you don't move the dist till you do and lock it down. Ignore the rest of the stuff it is in there for other systems.

#3 Tuning is timing, AFR, AE, cold starts, etc. What you will be trying to do is get the O2 corrections down to say -5% on the Ve table. Once you have this all cleaned up you will then do AE , cold starts etc. What you are shooting for as far as AFR, Timing etc will depend alot on the build but general AFR are light cruze - idle 14.7-14.0 medium load 14-13.5 low boost 13.0-12.0 and med boost and high boost 11.5-11.0. This also depends on what kind of gas you are tuning for. When tuning with no knock sensor you will have to error on the side of caution with the tune. Read plugs alot!! I usually calculate the dynamic compression ratio of a motor and then I have a starting point as far as where I should be timing wise etc. Alot of it is experiance basically been there done that.

Read the manual and take your time do not make big changes. Save your file each time you make a change so you can always go back.

When you start tuning you boost fueling you might want to spike that tank with some good gas for safety sake.

Nolan
 

denny

Active member
Re: BS3 Qs newbie.

10secTy said:
Did you read the manual that comes with the BS3? Alot of this is covered in it.

#1 what is your idle tps %? You need to set this about 2 higher than what you see at idle.
It looks like it is 2 so set it at 4
Do not worry that it does not go to 100% its not important like on a stock ecm.

#2 for HEI you set the crank rev at 6 degrees. This means your dist will be at 6 degrees.
You can check this to make sure you dist is set properly by using the static timing.
put 20 in the box and check the box. This will lock the timing at 20 then pull out your timing light and make sure you have 20. If you don't move the dist till you do and lock it down. Ignore the rest of the stuff it is in there for other systems.

#3 Tuning is timing, AFR, AE, cold starts, etc. What you will be trying to do is get the O2 corrections down to say -5% on the Ve table. Once you have this all cleaned up you will then do AE , cold starts etc. What you are shooting for as far as AFR, Timing etc will depend alot on the build but general AFR are light cruze - idle 14.7-14.0 medium load 14-13.5 low boost 13.0-12.0 and med boost and high boost 11.5-11.0. This also depends on what kind of gas you are tuning for. When tuning with no knock sensor you will have to error on the side of caution with the tune. Read plugs alot!! I usually calculate the dynamic compression ratio of a motor and then I have a starting point as far as where I should be timing wise etc. Alot of it is experiance basically been there done that.

Read the manual and take your time do not make big changes. Save your file each time you make a change so you can always go back.

When you start tuning you boost fueling you might want to spike that tank with some good gas for safety sake.

Nolan



Nolan, thank you.
I have the manual from here http://www.bigstuff3.com/gen3.pdf and I am referencing back to it, but its seem 'reading comprehension' is not one of my strong point.

#1 what is your idle tps %?
Yes its at 2.0 %

I have a lot info here to keep me busy for the rest of the week.

Thanks
Denny
 
Top