BS3 users, another question?

0966Sy

Code what?
Can you use/adjust the IC pump circuit to run electric fans on the SyTyBS3? A good example is the ultimate 50# chip that would control electric fans. If not at all possible the circuit will be removed. Along with the boost solinoid circuit, no longer needed with BS3. Unless of course its on a stock turbo/dp truck, if thats even possible. There is not much info about BS3 on the forums. I think this would be a good option if available inthe program.
 
Last edited:

Andreas

New member
Re: BS3 users, quick question?

Re: BS3 users, quick question?

There's two ways of running the BS3 with your SYTY. One is with the universial harness the other with the SYTY specific harness.

If you get the SYTY specific harness and wanne control electric fans you got to get a couple of new pins for the connectors to the BS3.
There is a function in BS3 to control the fans. Just punch in the temp you whant them to start/stop.
As for the IC pump I would have that running all the time, maybe have a switch for turning it off at long distance driving on the higway for extending the pump lifetime. Its not an IC pump function in BS3. But however if you not running electric fans you can use that function for the fans to control the IC pump. BUT its turn on/off points gonne be based on engine coolant temp.

If you got the SYTY specific harness the stock solenoid will work. The stock solenoid will also work with any other WG, its just a on/off valve.
 

0966Sy

Code what?
Re: BS3 users, quick question?

Re: BS3 users, quick question?

So the SYTY specific harness comes with a harness that connects to your existing wiring harness where your old ecm connected to? And the universal comes with a new engine wiring harness that will require to discard the original oem harness? What are the advantages and disadvantages of the SYTY specific BS3 and the Universal BS3?
Thanks, im getting confused as of what i need to do with the wiring harness in my engine bay.
 

autoaddictions

Active member
Re: BS3 users, another question?

The Sy ty harness will plug right in to the stock harness at the ecu location. You still have to run the BS3 injector harness and plug into you 6 injectors. Other than that ita a snap.
If you chose to use the standard harness that comes with the BS3 you will have to splice into all the sensors.If your understanding of wiring is weak id save the agg. and buy the SYTY harness. The BS3 will not control a stock 700r4 transmission either you will need to get a trans controler from TCI or other to control the lock up on your stock converter. If you go all out and swap out your stock trans for a upgraded 4L80e you can contol that with the BS3 system. Thats going to hurt the wallet a bit more.
 

0966Sy

Code what?
Re: BS3 users, engine harness options?

Re: BS3 users, engine harness options?

autoaddictions said:
If you chose to use the standard harness that comes with the BS3 you will have to splice into all the sensors.

So the standard harness you must (splice/solder) all your old sensor connectors, map,tps,iat,ect,est,coil,igniton module, except for the injector harness and 02 to the new harness?

autoaddictions said:
The BS3 will not control a stock 700r4 transmission either you will need to get a trans controler from TCI or other to control the lock up on your stock converter. If you go all out and swap out your stock trans for a upgraded 4L80e you can contol that with the BS3 system. Thats going to hurt the wallet a bit more.

I did not know this, although it will control the newer 4l60E. The plans have already been changed for the 4l80E w/T-brake. Yes, wallet breaking. Does the standard harness come with a trans harness or must you reuse your old one?

I plan on removing all of the uneeded stock wiring rats nest to make for a very clean simple new harness. Im ase certified in electrical and am looking forward to the removal of most of the stock harness, a/c connections/relay, Ic pump connections/relay,egr,stock 02,abs,boost solinoid/relayand fuse at alternator,fuel pump relay. Ive already started and it appears the stock harness will not be able to be saved. due to the bulkhead connector at the back of the fuse block. Still needed for guage ect,power from alt,starter wire,trans harness,grounds(2),wiper motor, and thats about it.
 

ghettosled

SYTY SUPERSTORE
Re: BS3 users, another question?

sounds like you have an idea of what wires are needed to be saved off the original engine ecu harness. The standalone universal harness will help you wire in things like the fan control, 2 step, hi/low fuel pump trigger, etc. The engine/trans harness' are sold separate, however if you buy the ecu with trans control it comes complete with everything you need.

Sounds to me like you would benefit from the standalone harness, especially since you have removed many of the stock wiring clusters (A/C, Boost Controller, 700r4 lockup, etc) and have an understanding of the stock wiring schematics.
 
Top