Built billet crank long block reliability?

Grimgrak

New member
I've heard some horror stories of stock blocks blowing up before 100k even with stock stuff.
So i'm left to wonder just how reliable these engines become after they are built from a reputable shop with billet crank vortec heads still keeping the rpms below 6500.
Whats the record for milage that someone has put on a built motor like this to date?
 

Tooky

Serious about performance
Re: Built billet crank long block reliability?

IMO it's not really a matter of reliability, it's a matter of how many mistakes the owner/operator makes while driving/racing/tuning it. From what I've seen, engines blow up more often because of mistakes (wastegate hose came off, owner continued to hammer it, or turned up high boost for "one race" without adding high octane to the tank, etc.), than they do from just "too much WOT".

I bought my truck with 26K now it has 78K, raced 400 miles on a road course (split across 2 years), probably 5000 WOT runs, its still a bone stock shortblock. I have a local friend who also beat the piss out of his original motor until 146,000 miles. So the stock stuff can last a very long time when monitored properly for detonation. I don't think it's really a matter of too much WOT.

You would assume an "upgraded" motor would last even longer than that, but I think the original rule still applies (depends on how the owner treated it).

The only example I can think of off the top of my head of someone with a built motor and a ton of miles is Jimmy with like 60K hard miles on his McCoy motor. I'm sure there are more though.

On the other hand I know a guy who went through at least 3 fully forged motors (stock crank though) at the rate of 1 a month. How did his "professionally built" motor not last as long as ours? Operator error - the guy couldn't understand that you can't continue to floor it when it's pinging and the KR is reading 18*.
 

Jimmy

Banned
Re: Built billet crank long block reliability?

:stupid:

I would think it would last forever if you don't knock it. I don't know how spinning a 4.3 to 6500 will affect it though. Ask the Campbell Automotive guys.

I have a stock crank,it has 168k miles on it,81k since I had the engine rebuilt. I don't knock it,and it never sees over 4800 rpms,but then again it is just a stockish slow tuck.
 

10secTy

Sy-Ty builder and Tuner
Re: Built billet crank long block reliability?

Good point, lots of people have broken full bowtie builds. If you can build it they can break it.


Nolan

TookyCat said:
IMO it's not really a matter of reliability, it's a matter of how many mistakes the owner/operator makes while driving/racing/tuning it. From what I've seen, engines blow up more often because of mistakes (wastegate hose came off, owner continued to hammer it, or turned up high boost for "one race" without adding high octane to the tank, etc.), than they do from just "too much WOT".

I bought my truck with 26K now it has 78K, raced 400 miles on a road course (split across 2 years), probably 5000 WOT runs, its still a bone stock shortblock. I have a local friend who also beat the piss out of his original motor until 146,000 miles. So the stock stuff can last a very long time when monitored properly for detonation. I don't think it's really a matter of too much WOT.

You would assume an "upgraded" motor would last even longer than that, but I think the original rule still applies (depends on how the owner treated it).

The only example I can think of off the top of my head of someone with a built motor and a ton of miles is Jimmy with like 60K hard miles on his McCoy motor. I'm sure there are more though.

On the other hand I know a guy who went through at least 3 fully forged motors (stock crank though) at the rate of 1 a month. How did his "professionally built" motor not last as long as ours? Operator error - the guy couldn't understand that you can't continue to floor it when it's pinging and the KR is reading 18*.
 

Grimgrak

New member
Re: Built billet crank long block reliability?

For things like the wastegate line coming off is the BS3 able to to (upon sensing knock) drop rpm to 2k max and retard timing , basically putting it in limp mode until the owner loads up the laptop to reset the limp mode?
 

turbodig

Active member
Re: Built billet crank long block reliability?

Grimgrak said:
For things like the wastegate line coming off is the BS3 able to to (upon sensing knock) drop rpm to 2k max and retard timing , basically putting it in limp mode until the owner loads up the laptop to reset the limp mode?

Hey... that's a good idea. I'm gonna look at that for the $59 stuff...
 

10secTy

Sy-Ty builder and Tuner
Re: Built billet crank long block reliability?

No but it does retard timing.

With your build it will not need to be run on the edge to make big power.

Nolan


Grimgrak said:
For things like the wastegate line coming off is the BS3 able to to (upon sensing knock) drop rpm to 2k max and retard timing , basically putting it in limp mode until the owner loads up the laptop to reset the limp mode?
 
Top