Chilled Gasoline?

Is anyone running or heard of the benifits of chilling the gasoline before it is injected into the motor. Seen these containers that were sold(forget where) that ran a coil if line in a seal canister. The coil would flow the fuel prior to being injected and the canister would house the ice water. This would only be logical to use at the track, I know, but would it work in like a H20 injection??(by making the air more dense and reducing knock>??)
 

Daryl H

Donating Member
Jegs sells the "Cool Cans"

EFI fuel pumps flow around 50 gallons an hour.
Thats a lot of fuel to cool.
I think the "Cool Cans" are more suited for carburetored engines.
 

Bill Z

Donating Member
Chilled Gasoline?

I have seen the cold can used on Grand Nationals this year at Bolingreen..

The trick is to get the can as close to the fuel rail as possible.

The theory is that the cold fuel hits the hot manifold and vaporizes better. Also, fuel expands as it gets warmer. So cold fuel is supposed to be more concentrated per
 

bshaw

New member
My 928 has a fuel cooler installed from the factory. There's a small (coke can) sized canister the fuel flows through before returning to the tank. The A/C line runs through it on the way to the interior. Theory is that idling in traffic on hot days, the fuel returned to the tank from the regulators can cause the gas to get too hot.
 

'JustDreamin'

Dream: 6LV8 Turbo Bravada
I think you could get more power, but I expect that the difference would be pretty slight. Most of the heat required to vaporize the fuel is due to the state change (liquid at boiling point to vapor at boiling point). Thats the heat of vaporization. The heat required to change the fuel temp a couple of degrees is a significanly smaller number (orders of magnitude smaller).

On a carb'd application, this could cause carb icing in low temps a/o high humidity environments. Fuel injection shouldn't have any probs at all.

I don't know if the investment, installation requirements (space and ice-water) and potential for fuel system complications (additional stress on the pump, etc.) would be worthwhile.

Just my 0.02

'Dreamin'
 

Boosted

New member
Be careful with Moroso cool can....its not good for EFI
Along these lines, Design Engineerings, Cryo system
They have the pice that the air flows over, to cool, they also offer intercooler sprayers, and a fuel line block that the carbon dioxide runs through, so in theory, you can cool the fuel, then line to the air piece, and then line to intercooler sprayer, all on one unit.
Bottle costs about 10 bucks to fill versus 40? for nitrous.

I intend to run a setup on TY once the Saab A2A is done. I am going to plumb for all 3.
 

JSM

Active member
I know of a person that puts his race fuel in a 55 gallon drum of ice for his drag car.

Right before the round, puts the gas in the car.

Granted this is a quick ride (low 10's) but for him it is worth ~.05 seconds.

In a turbo application, efi. Not sure. He did mention the cool fuel will richen the mixture up so tuning for it may be needed.
 

Lynn D. Brown

New member
Cooling Gasoline

Cooling Gasoline

The main thing that it will be beneficial to cool is the Intake Air. Air density will increase
and therefore you will be able to get more LBS of air in and therefore more fuel also. Cooling the gasoline is of much more limited benefit because liquid density does not increase significantly with temperature.
 

'JustDreamin'

Dream: 6LV8 Turbo Bravada
Hey Guys....

I got to thinking about this while in the shower, and decided that it was worth a second look and an actual engineering evalutation.

Here is what I dug up. Specific Heat of Gasoline (Cp) is .53 BTU / lb F, Specific Heat of Air (at standard temp and pressure) is .24 BTU / lb F, Specific Heat of Water is 1 BTU / lb F (it is the reference point for the scale). What this means is it takes twice the energy to raise water 1 deg F as it does Gasoline (and 4 times the energy of air).

Here are my assumptions.
Say its hot, and therefore the gasoline in the tank is hot (say 100 F). We pump it forward and it gets warmer (call it 135 F for easy math). If we inject it in the engine, its is in its liquid state, and therefore gets to the boiling point and then vaporizes. If we cool it, that part won't change any.

Say we install a cooler, and drop our 135 F gasoline down to 35 F (nice and cold). What happens now is that the gasoline has to get from 35 F to 135 F before it is just as before. So we have created a difference. What is that difference? Depends upon amount of gas we pump in.

Lets assume we're using 6 50 lb / hr injectors (at 100% duty cycle), therefore they flow 300 lbs of fuel / hr. Obviously we won't run the engine at peak power for an hour, or should we be using 100% duty cycle, but play along for fun.

Here's the formula: Q (amount of heat in BTU's) = Cp x Mass (in lbs) x Temp change (in F). So, if we get 300 lbs of fuel to rise from 35 F to 135 F, we ge 15900 BTU / HR (for the record, a "ton" of air conditioning is 13500). Thats a significant effect.

Seeing what the impact will be on the air temperature, we use the same formula to solve for Temp Change. Need to know the amount of air (lets use 11:1 AFR) which yields 3300 lbs of air / hr. At that point we get a 20 F decrease in air temp. This assumes that all the heat that is raising the temp of the fuel is coming from the intake air charge, which probably isn't 100 % accurate. This also assumes that the specific heat of air at 15 psi of boost or so and 150 F is reasonably close to the above listed specific heat (which it might not be).


Conclusion (besides wow, thats alot of typing). In NA race vehicles, it probably is worthwhile. In turbo'd vehicles, it may depend upon a bunch of other things as to whether it is worthwhile or not. Like do you have space, how big / good / efficient / etc is you intercooler, how much will your installation cost, etc. I probably should have run a calculation as to what lowering the intake air temp by 20 F would do (as far as horsepower / torque) but I didn't.

If anybody has read this far, please make sure that I didn't make a stupid assumption / math type error, or some other kind of dumb mistake. The stupid mistakes are the one's that usually get me.


'Dreamin'
 
Top