Code 31- Overboost

Michael

Member
My 92 Ty has been getting an intermittent Code 31 when under hard acceleration. My mechanical boost gauge (plumbed into a tee off of the brake booster intake fitting) shows ~17 psi when the fault occurs. It started getting worse (happening more often) a few weeks ago, which led me to install the mech gauge, and eventually replaced the wastegate solenoid. This got me back to the occasional fault level. I have replaced the MAP sensor, and run through all the Code 31 checks from the service manual (all passed), but the problem persists.

I have Datamaster, but have never used it (plan to try it out this weekend).

The truck is mostly stock, except for a 160° thermostat, underdrive pulleys, cold air box, and ATR Cat-back exhaust.

Does anyone have any suggestions of where to look next?

Thanks and regards,
Michael
 

Captain Morgan

Moderated User
simple enough, ur running too much boost for the stock chip.

best and easiest fix would be to adjust the wastegate rod.

try turning it out (make the rod longer) about 1.5-2 turns.

see if it happens again.


**edit** all fixed :)
 

Michael

Member
Thanks, I'll try that. The part I am wondering about is: why did it work fine for 2 years (that I know of, probably longer), then start screwing up a few months ago? I even took it to the track a few times, and never had this problem. The way it works now, I can get it to happen every time if I stay in the throttle long enough.

Is there something in the wastegate which could be wearing?

Thanks,
Michael
 

justin949

New member
i think it is your atr cat back free flowing exhaust i cut my muffler
out, and did a straight pipe now when it is cold or running strong it will over boost {happens very little]
 

Flyin Ryan

hated cuz he drives fords
A vacuum leak can also cause code 31.... I adjusted and adjusted my wastegate rod and still had the issue til I noticed a cracked vacuum line so you might want to check your lines also.. in my case I think it was a combination of both causing the overboost.
 

Michael

Member
Ryan,
What vacuum lines were cracked? I wondered about mine from the wastegate solenoid down to the wastegate, but they seem to check out okay (but they look a little rough, so I have replacements on order).

Incidentally, I tried driving it with the wastegate solenoid bypassed (ran the vacuum/pressure lines around the solenoid), and it would only generate 5 psi (and no code 31's needless to say).

I am also wondering if the change in atmospheric conditions is responsible (we moved from North Carolina to Oregon). Now that I think about it, I had not really gotten into heavy boost conditions since it has been in Oregon, until the times when I noted the code 31 problem. I suppose I could have been on the ragged edge of overboost before, and the higher typical atmospheric pressure here could be enough to push it over the edge.

Thanks,
Michael
 

Flyin Ryan

hated cuz he drives fords
Michael,

My vac leaks were on the line for the wastegate from what I could tell but
do your self a favor and replace them all, and take the time to zip tie the ends so they can't blow off under boost :roll:

The change in atmospheric conditions could be it which adjusting the wastegate a little would resolve it then. Like I said it was a combo between shitty vac lines and rod adjustment for me so good luck.

Ryan
 

Michael

Member
I have tried it with the wastegate rod lengthened by 1½, then 3 turns, without a noticeable difference (still runs straight up to 17 psi & gets code 31 if I stay in it long enough).

I'll try one more lengthening while waiting for my new wastegate vacuum lines to arrive. I am beginning to wonder if it is time to start playing with the Memcal. I have an ATR Pitbull memcal, but IIRC, the prevailing advice was to try to customize my own.

Thanks,
Michael
 

Michael

Member
Just to close the loop on this one:
I stand corrected, Ryan had it right the 1st time!
It turns out that there was a small tear in the "boot" portion of the vacuum line which attached to the wastegate actuator. When the truck (and boot) were cold, there was minimal leakage. When they were warm, the pressure of the turbo inlet hose "leaning" on the boot caused significant leaking.

I also noticed the PCV valve pulled out of the valve cover and tucked back by the firewall! I suspect that this (and possibly tearing of the vacuum hose boot) occurred during the DEQ emissions inspection. I had forgotten all about that event, since my wife had taken it through.

Now I just need to figure out why I still have occasional high KR (as indicated by Datamaster).

Regards,
Michael
 
Top