code 45, swapped injectors, etc *help?*

bezerk

New member
this is the story;

i''am working on a truck, when it came to my house didn't run.
swapped plugs, and now it runs, (old plugs were bad).

first it would shut down after a couple of seconds of idling, feul pressure would drop when engine was shut off, and smelled extremly rich.

so i swapped the injectors, now it doesn;t shut of idling, but it runs like crap, when i get on the throttle most of the problems will go away.

still the feul pressure drops when i shut down teh engine.
datamaster gave me a code 45, with MV that were around 430 at idle (not that rich).
but you can smell it being rich
FP is set at 45.
(stock injectors, MSD dist. new wires, new vac. lines)
i can't tell what happened with this truck, i am only working on it, cause somebody was working on it, and made it worse than it was.

i got some ideas, but maybe somebody around here might now what could be wrong.
and it would be really weird that i swapped out a set of stock injectors that also had a bad one.
no feul in vacuum line

Thanks
 

TurboManiacal

Donating Member
Re: code 45, swapped injectors, etc *help?*

Ok Ok...just so everybody knows...It's my Syclone. I finally broke down and admitted that I can't make this truck run by myself so I towed it up to the Netherlands and Rene is working on it for me.

BTW...for those that don't know...Rene has finally got his Typhoon running and it's damn quick. PT&E 61 turbo / Waller Trans / RPM Motor. It's a beast.
 
Last edited:

Jimmy

Banned
Re: code 45, swapped injectors, etc *help?*

IMO fuel pump problem.It should be holding pressure when you shut it off,if it's not the injectors or FPR,it's the check valve in the fuel pump ;)
 

bezerk

New member
Re: code 45, swapped injectors, etc *help?*

SyGoat said:
Ok Ok...just so everybody knows...It's my Syclone. I finally broke down and admitted that I can't make this truck run by myself so I towed it up to the Netherlands and Rene is working on it for me.

BTW...for those that don't know...Rene has finally got his Typhoon running and it's damn quick. PT&E 61 turbo / Waller Trans / McCoy Motor. It's a beast.

okay, small correction, it isn't a Mc Coy..........

it could be the feulpump, but that won't do annything for the rest of the problems i subscribed.

i will try and hunt this problem down, but if you got some ideas
 
Last edited:

leroy

Donating Member
Re: code 45, swapped injectors, etc *help?*

Voltage okay? Alternator output drops at idle can cause injector or ecm problems.

Can you post a datamaster file?

Jim
 

Jimmy

Banned
Re: code 45, swapped injectors, etc *help?*

bezerk said:
okay, small correction, it''s a RPM engine (thanks mike)

it could be the feulpump, but that won't do annything for the rest of the problems i subscribed.

i will try and hunt this problem down, but if you got some ideas
Yes it would cause all of the problems you are describing.Being that the fuel pump is WOT trying to pressurize the system,but can't cause it's now an open sytem instead of closed. :tup:
 

TurboManiacal

Donating Member
Re: code 45, swapped injectors, etc *help?*

Jimmy said:
Yes it would cause all of the problems you are describing.Being that the fuel pump is WOT trying to pressurize the system,but can't cause it's now an open sytem instead of closed. :tup:

Fuel pump was replaced with Walbro last year. The only problem I can think of is that I may or may not have forgotten to tighten all the sending unit connections when I did it.
 

TurboManiacal

Donating Member
Re: code 45, swapped injectors, etc *help?*

leroy said:
Voltage okay? Alternator output drops at idle can cause injector or ecm problems.

Can you post a datamaster file?

Jim

I've been told the pulley on the Alternator is NOT correct. I'm also missing a tensioner pulley on the belt system.
 

bezerk

New member
Re: code 45, swapped injectors, etc *help?*

volts are fine, you don;t miss a pulley, you just routed the belt under the idler pulley, instead of above.

volts are okay, gonna post a DM file soon.
 

bezerk

New member
Re: code 45, swapped injectors, etc *help?*

ohw, and i want to offer this guy some money, to get rid of this POS nightmare truck, but he still thinks that it will be good one day, so he can enjoy driving it without an headache??!
 

TurboManiacal

Donating Member
Re: code 45, swapped injectors, etc *help?*

Shutup.

Look again. There is a missing pulley. That's why I had you bring one down here. (I did bring it back with the truck right?)

You'll probably need a new serpentine belt.
 

myclone

Donating Member
Re: code 45, swapped injectors, etc *help?*

Idling rich could be a MAP sensor/vaccum issue, O2 sensor issue (in closed loop), chip/ECM issue, FPR issue, or a couple of other things that are odd ball and prolly not the case.

If it was me, I didnt know siggy, and the truck showed up at my garage Id do the following starting with easiest to most PIA (IMO):

1) Verify MAP sensor is correct (2 bar or 3) for the chip thats being used.
2) Verify closed loop operation and T stat isnt stuck open/bad CTS causing low coolant temp read back.
3) Verify correct timing.
4) Verify "set timing" connector plugged in.
5) Verify MAP sensor is seeing manifold vaccum and giving the correct output in relation to vacuum with no "dead spots" or other issues.
6) Check TPS for off idle "dead spot" in output (voltage/resistance should be linear throughout the TPS travel).
7) Check IAC counts.
8) Check short term counts.

HTH

ps.. hope youre doing well siggy.
 

bezerk

New member
Re: code 45, swapped injectors, etc *help?*

okay list of the following things i did
* swapped around chips and map sensors and now have the moatoes working with the 3 bar map.
* changed the big pulley of the alternator to smaller one
* erased codes
* put in some new gas.

well, now it isn;t throwing codes anymore, but still is running pig rich at idle.
the battery of my laptop died, so i will record a new datamaster run tomorrow.

next;
will swap the AFPR to a FPR and see if feulpressure still drops.
if it doesn't, going back to completly stock setup.
there is one ground wire, that has a bad connection.
 

bezerk

New member
Re: code 45, swapped injectors, etc *help?*

i was finally able to get some datamaster files.. who wants them?
 
Top