Contemplating stand alone system

Poconojoe

Donating Member
Re: Contemplating stand alone system

As innovative as these alternatives are, how much will the costs be?

$295 for the Moroso thing.
The 411 PCM - say $50
The dis with crank signal - $50 min
The front cover with timing signal etc. - $20-50?

$450...

You're not shy of the cost of the TCI controller and you've got a heck of a lot less work in front of you. I might be wrong....

FWIW PCS, who made my controller, were AWESOME with their customer support. They sent a new unit via FEDEX overnight to the UK with a new harness as well as soon as I thought it might be bad. Turns out it was actually the valve body.

With that kind of service I'd take the (very small) risk on the TCI/PCS unit.

Why would you need the Moroso thing, if the 411 could run the trans (4L60E), like it does in a couple of million cars already on the road, it could also run a 4L80E
 

JSM

Active member
Re: Contemplating stand alone system

Why would you need the Moroso thing, if the 411 could run the trans (4L60E), like it does in a couple of million cars already on the road, it could also run a 4L80E

Although the 60e and 80e share the same plug they are not the same for logic. Not saying a 411 can't as I have never messed with one, just a word of warning.
 

ViciousV6

400HP/550FTLB
Re: Contemplating stand alone system

What did the 411 come out of originally?

See when i built my LS Malibu i sold my BS3 and went to the 411 set-up which smack me in the head, i could of kept the BS3 and it would of worked on the set-up.

THey just sold a BS3 on LS1Tech for $1700.00 --- you just keep your eyes out and you could find one cheaper slightly used.

RPM has some of the best prices -- 24-2500 complete with trans, data logging, with stand alone harness.

I recommend switching harness(stand alone harness) to eliminate any issue between factory harness and DFI harness or power voltage concerns.

I'm working on a T/A with a stage 2 GN motor with Piggyback Accel Gen 7 and having voltage issue. So now if they used a stand alone hook up done but now got trace everything and figure out problem.

You can also switch your BS3 from V6 to V8 and the program and tuning is all included ---- with LS computer you need to buy HP Tuners for 500-600 bucks to tune and play with it so add that on to your prcing too. LS computers have many more tables and circuits as with BS3 just what you need to tune and drive car.

Ralph
 

Poconojoe

Donating Member
Re: Contemplating stand alone system

Although the 60e and 80e share the same plug they are not the same for logic. Not saying a 411 can't as I have never messed with one, just a word of warning.

To switch from the 4L60e to the 4L60E with the 411, you just swap a few wires and change the tranny sergment in the tune, about 10 minutes to do each of them
 

Poconojoe

Donating Member
Re: Contemplating stand alone system

You can also switch your BS3 from V6 to V8 and the program and tuning is all included ---- with LS computer you need to buy HP Tuners for 500-600 bucks to tune and play with it so add that on to your prcing too. LS computers have many more tables and circuits as with BS3 just what you need to tune and drive car.

Ralph


Yes but the $500 gets you the ability to tune up to 4 vehicles
You can buy a 4.3 harness and PCM for around $100, add another $100 for the stuff to mod ther harness to standalone, I'mm still only at $700, about a third or a fourth of the cost of a BS3 and the second one would cost you even less, since you already have the tuning package.
 

qbnkiller

Conflaguration Specialist
Re: Contemplating stand alone system

See when i built my LS Malibu i sold my BS3 and went to the 411 set-up which smack me in the head, i could of kept the BS3 and it would of worked on the set-up.

THey just sold a BS3 on LS1Tech for $1700.00 --- you just keep your eyes out and you could find one cheaper slightly used.

RPM has some of the best prices -- 24-2500 complete with trans, data logging, with stand alone harness.

I recommend switching harness(stand alone harness) to eliminate any issue between factory harness and DFI harness or power voltage concerns.

I'm working on a T/A with a stage 2 GN motor with Piggyback Accel Gen 7 and having voltage issue. So now if they used a stand alone hook up done but now got trace everything and figure out problem.

You can also switch your BS3 from V6 to V8 and the program and tuning is all included ---- with LS computer you need to buy HP Tuners for 500-600 bucks to tune and play with it so add that on to your prcing too. LS computers have many more tables and circuits as with BS3 just what you need to tune and drive car.

Ralph

I'm with Ralph on this one. I love my BS3 now that I understand it. Does everything I want and more if I want to reflash it.
 

ViciousV6

400HP/550FTLB
Re: Contemplating stand alone system

I'm with Ralph on this one. I love my BS3 now that I understand it. Does everything I want and more if I want to reflash it.

I just went through weeks of issue with my LS Motor in the Malibu and even if you don't know what your doing the big stuff 3 is much easier to understand and learn. The Factory ecm have much more tables, graph, torque management, start up tables. Power enrichment, they don't run widebands only if you buy the Hp Tuner Pro system.

My BS3 was tuned in one week and never had to change a thing with it.

Can't say the same for my LS motor and ECM.

Its your Headache, not mine, i learned my lesson once.

Ralph
ViciousV6

P.S. QB They will all learn.
 
Last edited:

turbodig

Active member
Re: Contemplating stand alone system

Damn Matt, awesome write up!! I think I may give that a whirl.

x2.

I'm really kinda surprised somebody hasn't started a code59-like project to do a trans controller based on this ECM. All It would take is a really good XDF definition of just the trans parameters.

It's cheap, it works, and while it has *lots* of very complicated stuff buried in the trans code, for the most part all you need to know is the shift line pressure table and the up/down shifts.
 

JSM

Active member
Re: Contemplating stand alone system

I know someone that might have done that dig... LOL
 

TYTILIDIE

METH HEAD
Re: Contemplating stand alone system

Couple questons here. There are 12 green highlighted circuits that are going to the connector. Well, there are only 11 pins marked in the schematic. I am also noticing that some of the yellow highlighted areas are saying I think these need to be active. What does this mean? 12 volts? My last question, for now is, for the CEL, can I just simply use an LED or do I need to do something special?

I got my harness, trans, ECM and DRAC out of a 95 OBDI truck so I have everything I need from the same vehicle. I plan on doing a tech article on the whole thing from a dumbass's point of view and plan to start exposing the harness this weekend.
 

0966Sy

Code what?
Re: Contemplating stand alone system

You already have the 80e, just purchase the BS3 with trans control and be done with it. How would that cost 6k? Get a standalone setup, plug and play harness allows for to many connections/voltage issues and leaves a mess of unused wiring. As long as your 80e is the late model with the 13pin i believe, im using a 60e and BS3 standalone.
 

TYTILIDIE

METH HEAD
Re: Contemplating stand alone system

Yeah I already did the stock ECM route. I may go BS3 sometime in the future but a business opportunity may be coming my way and I may need to stop spending money on the TY for a while. Even with out that, I guess I should say I'll likely get BS3 next time I have $2800.00 laying around. But for now, that stock ECM works great. I pulled all of the unused wiring out of the harness. You can see what I did here...http://www.syty.net/forums/showthread.php?t=82911
 

qbnkiller

Conflaguration Specialist
Re: Contemplating stand alone system

....still think a BS3 is the way to go at the moment. If you're looking for a deal, let me know!
 

sy605

Member
Re: Contemplating stand alone system

OPTION 4: 0411 PCM. Cheap, available, tunable (including trans) w /faster processer.

Need a 2001+ 4.3 harness. You would have to add a crank sensor and change/modify the timing cover, add a newer distributor w/cam sensor (PnP), retrofit the knock sensor (two wire vs one), make an injector harness and switch over a few connectors.

Poconoejoe is converting his Sy to 0411 PCM. He may have found an even better harness off of a FWD V6.

Joe?

Has this been done? Very interested in the outcome. I used the 411 in my LS GN swap and love it. Being able to use factory components and tuning myself is awesome. Plus sequential always helps the MPGs.
 

leadfoot

Member
Re: Contemplating stand alone system

Has this been done? Very interested in the outcome. I used the 411 in my LS GN swap and love it. Being able to use factory components and tuning myself is awesome. Plus sequential always helps the MPGs.

Yes. I am up and running with a Ty engine using a 4L60e. In the (slow) process of a Speed Density tune with EFIlive. :squint:

For now using a manual boost controller @ 8psi, but overall most of it was plug and play besides adding or converting a few sensors to the older engine. (eg crank sensor)

Since this build there has been a few good discoveries such as a PnP injector harness and correct trans tail piece if you go AWD.

One of these days I should do a write up. :roll:

Here is the project thread:

http://www.syty.net/forums/showthread.php?t=29202&highlight=extreme+xtreme
 

MadMike

Member
Re: Contemplating stand alone system

Megasquirt? Mine has been great. It cost me like $700 to do the full stand alone w/ trans controller. And now that I'm setup up the add on functions are really cheap. Like adding electronic boost controller is $50. Same for egt. Launch control, Does flex fuel . Has an auto tune feature. If you can dream it it can do it.

You re a little on your own for support but if you have a little electrical knowledge its no harder than other big money stand alones.
 
Top