Did I do something dumb?

TheNeek

this is my serious face
Well the board was down all of yesterday. So I might have done something dumb.

The truck failed it's first shot at AZ emissions. Doubled the allowable limit of HC at idle. It has a dead miss. So it's either compression or ignition. I figure I'll change the plugs even though Branden just did it before he sold me the truck. Start on the driver's side pull the inner fender well. Etc. Etc. Man that plug behind the steering shaft is a BITCH. Plugs look great for having less than 3,000 miles on them. I change them out anyway. I button up the driver's side. Get to the passenger side. #6 plug wire comes apart in my hand. The connection stays on the plug and busts out of the boot. I think these are those "black beauty" wires. They say turbo on them and Branden said ATR or something. "Huh" I think... So I cut the boot open and recrimp it on just to see if the truck will idle better. Slip the sliced boot on the wire and fire it up. Idles great through the cold start and for about 3 or 4 minutes after. I can hear it missing a little, but not half as bad as before. "problem solved". Well I check the boards today after purchasing wires.

I bought MSD wires from summit. Those don't seem to be a good choice for some people. But here is the kicker. The truck now has CR43TS plugs in it. They aren't R's thank god, but not the 42's that I pulled out. Is this a problem?

3 questions as well.
1. What should the truck pull vacuum wise at idle / cruise? I get about 7.5 lbs of vacuum.
2. I get a check engine light at cruise only on the freeway after about 45 minutes of driving. Bad EGR? or is the truck just pissed off I'm putting miles on it?
3. Best intake for the truck if I'm willing to do a battery relocate? The intake is old/cracking etc.

Thanks guys. You'll find out I write novels for posts. I hope some of you enjoy reading.

Nic
 

dgoodhue

BuSTeD 4.3
Re: Did I do something dumb?

EGR errors can be caused by a vauum leak. At idle the truck should be a 20-22 in Vacuum or about -10-11psi. At cruise vacuum is detrmine by engine load.
 

QUICK STORM

B.A.M.F. BMW Tech
Re: Did I do something dumb?

hey nic, i would put some ngk ur5's in it. after reading everything on the board it seems that these plugs are now pretty much the norm for stock trucks. you should get about 17-20in. hg of vacuum at idle. its funny i never got check engine lights when i drove it. best intake would probably be a DIYer, search the board some people use muffler piping etc....

my suggestion is to do a compression test. probably wouldn't be a bad idea to pull the heads off and do some head gaskets, they are 13yrs. old.

i apologize for any wrong that i have done you.
 

TheNeek

this is my serious face
Re: Did I do something dumb?

TyphoonB said:
hey nic, i would put some ngk ur5's in it. after reading everything on the board it seems that these plugs are now pretty much the norm for stock trucks. you should get about 17-20in. hg of vacuum at idle. its funny i never got check engine lights when i drove it. best intake would probably be a DIYer, search the board some people use muffler piping etc....

my suggestion is to do a compression test. probably wouldn't be a bad idea to pull the heads off and do some head gaskets, they are 13yrs. old.

i apologize for any wrong that i have done you.

No appologizes required. I've been working on old cars since I was old enough to pick up a wrench. I knew what I was getting into. Besides, if the truck was perfect I wouldn't know what to do with myself. I've already talked to cometic about MLS gaskets for it. Just want to pass emissions before I go that far. Would a leaky head gasket cause a check engine light?
 

dgoodhue

BuSTeD 4.3
Re: Did I do something dumb?

TheNeek said:
No appologizes required. I've been working on old cars since I was old enough to pick up a wrench. I knew what I was getting into. Besides, if the truck was perfect I wouldn't know what to do with myself. I've already talked to cometic about MLS gaskets for it. Just want to pass emissions before I go that far. Would a leaky head gasket cause a check engine light?


With our trucks, Head gasket problems are uncommon. Do you have a scan tool? I woul dstrat with that before pulling ht eheads and all the work required.
 

TheNeek

this is my serious face
Re: Did I do something dumb?

Dave,
Data master is something I hope to invest in soon. I'm just brain storming what else could be causing a miss fire. I'm 95% sure the plug wire is the culprete. My dad bet me a dollar :)
 

QUICK STORM

B.A.M.F. BMW Tech
Re: Did I do something dumb?

TheNeek said:
Dave,
Data master is something I hope to invest in soon. I'm just brain storming what else could be causing a miss fire. I'm 95% sure the plug wire is the culprete. My dad bet me a dollar :)

i need to get a datamaster myself too.

i hope that the #6 wire/plug is the only thing bad, i'll be sending out the cat tomorrow.
 

TheNeek

this is my serious face
Re: Did I do something dumb?

TyphoonB said:
i need to get a datamaster myself too.

i hope that the #6 wire/plug is the only thing bad, i'll be sending out the cat tomorrow.

As far as I could tell when I crimped on that spark plug fitting again to the wire (for a temporary thing) it fired pretty well. A slight miss, but nothing as dramatic as before.
 

kentuc

Member
Re: Did I do something dumb?

Little miss = Emission Failure. Check out the basics first. You`ll be fine.
 

TheNeek

this is my serious face
Re: Did I do something dumb?

kentuc said:
Little miss = Emission Failure. Check out the basics first. You`ll be fine.

The new plug wires should button everything up. And the NGK plugs can't hurt either. Is it possible to pass without all the 'tricks'? Alcohol, 87 octane, disconnecting that timing wire etc.? Anyone think I can pass with just disconnecting that timing wire? Shit I can leave the kick plate off and unplug it for the test, then plug it back in again once I'm going. do you need to disconnect / connect with the engine off?
 

kentuc

Member
Re: Did I do something dumb?

If it runs good, no tricks.
The first time I had mine checked they said I had the wrong engine! It says Cyclone on it!
I also have an 82 S-10 with a TPI V8. Every time after picking up the hood, they ask me if it`s four or six cylinder.
I just say it`s not a four.
 
Last edited:

TheNeek

this is my serious face
Re: Did I do something dumb?

UPDATE:
New MSD plug wires and NGK UR-5's = No change. The truck performs really well off of idle so I'm figuring it is probably a a fueling issue. I popped off the intercooler and upper intake manifold. I am having the upper intake professionally cleaned at my friends shop along with the injectors cleaned and performance tested. I have been inspecting vacuum lines as I go, they all look brand new. Should have the truck back together mid week for another run at emissions and to see if the miss goes away. If I can't get that done I'm going to pull the tan wire and dump some alcohol in it, just to get it to pass, then worry about this stuff later.
 

jwaller

Evil Genius/SyTy Guru
Re: Did I do something dumb?

is your egr valve stuck? this can cause many of your problems.
 

TheNeek

this is my serious face
Re: Did I do something dumb?

jwaller said:
is your egr valve stuck? this can cause many of your problems.

I checked the valve after I removed it. Didn't appear to be blocked. I have a new one just in case. I figure I'll install the new one and unplug the EGR solenoid for emissions, to make sure it stays sealed in case the solenoid is malfunctioning. Upper manifold and injectors are cleaned. New seals on the injectors and new maniold and throttle body gaskets on order.

One thing of interest is that the PCCV sort of came apart off the valve cover. It just slipped out. Not sure if that is normal. The inside of the intake is covered in oil. I also purchased a new air temp sensor, the one in the manifold was covered with black oil. I'm thinking all this love will pay off come thursday when the Ty gets it's anal probe again.
 

cr133r

New member
Re: Did I do something dumb?

My Ty just passed blowing literally zero's on the test. Had to run it twice because it didn't register anything the first time. Bone stock with 123k miles on the clock. Just in good shape.

It really sounds like a vacuum leak you are chasing. My time is pretty tight, but I may be able to take a look for you if you'd like a bit of help. I'm located near Golf Links/Pantano.

Billy
 

TheNeek

this is my serious face
Re: Did I do something dumb?

cr133r said:
My Ty just passed blowing literally zero's on the test. Had to run it twice because it didn't register anything the first time. Bone stock with 123k miles on the clock. Just in good shape.

It really sounds like a vacuum leak you are chasing. My time is pretty tight, but I may be able to take a look for you if you'd like a bit of help. I'm located near Golf Links/Pantano.

Billy

Thanks Billy. What you say is true. I got the Ty all buttoned up today (Aug 10) and fired it up after reseting the ECM. Idled well as usual. Took it out for a late night spin to get it warmed up. Had a hell of a time building boost pressure. I think I might have cracked the bad vacuum line during the wrenching. Once home I let it idle and the dead miss is still there. I am going to baby drive it over to European AutoTech tomrorow and hook up the vac system to their smoke machine if I can use it. Those PCCV hoses are super loose, but don't effect vacuum right?

The search continues... and I will contact you if my ideas run dry. Thanks again.
 
Last edited:

TheNeek

this is my serious face
Re: Did I do something dumb?

Cold hard facts revealed:

Boost leak was because I'm an idiot and is now fixed.

Bicycle tire test shows TB leaking on both shaft ends and no where else that I or my roommates could see. So that is next on my list. I need to contact that company in Texas.

More interesting stuff to ponder:
The intermitant miss only happens once the truck has gone into closed loop (warm). At start up the truck idles well and sounds awesome. Could this vacuum leak cause such a miss after the truck has warmed up? Maybe I just need datamaster.

Who thinks I can pass with two gallons of denatured in the tank?
Thanks for taking care of the noob.

Nic
 

100in6

100in6
Re: Did I do something dumb?

some things that caused engine light on my first one to come on were bad fuel pressure and a bad O2 sensor. do you have an adjustable fuel pressure regulator? turning down the fuel pressure helps pass the test. just don't get into the boost when driving it to the inspection station. also, i'm not sure if there's any scientific data on this, but i have squirted carb cleaner on an O2 sensor that wasn't working and tried to spray it a little cleaner and it did seem to work. no more light. probably not a long time fix, but it did work for a while. if you have an adjustable fuel pressure regulator you could turn the pressure down and also try the starter fluid on the O2. those are both basically free things.

also, i know a lot of guys are usin cometics, but we just had trouble with a set leaking and was just told of some others that leaked. everything has to be REALLY flat for them. for a fairly stock motor that isn't running big boost on a big turbo i would stick with victors or something and not spend the money for cometics. maybe felpro gaskets. lots cheaper and have worked for years

just my 2 cents. good luck on passin

les
 

TheNeek

this is my serious face
Re: Did I do something dumb?

Passed... just now. HC limi was 220 I blew 115. disconnected tan wire (idled surprisingly well) and a gallon of denatured (not sure if that helped a ton. The idle was real smooth with the wire disconnected. I'm thinking I might have to reset the timing. Looks like a bitch to loosen the distributor though. Next stop DMV in the morning. THANKS for all your help guys!
 
Top