ESC Module

Ty 1885

Member
Can anyone tell me where is ESC Module located ? I'm putting FAST XFI with TY harness but cant locate the Module to plug in.

Thanks..
 

NecroWolf

lost marbles member
Re: ESC Module

uh i think he's actually thinking about the knock module which is on the stock chip. if you have the casper harness the module that fits there isn't on our truck. i've seen one on a 93 blazer's firewall at the salvage yard.
 

Ty 1885

Member
Re: ESC Module

Yes Its Caspers harness. So do i need that module ? Or is there other way it will work ?
 

NecroWolf

lost marbles member
Re: ESC Module

i'm not using it but i'm wondering if i do need it, since i'm having trouble getting it to idle right. i think i might grab one next time i am at pick and pull and try. are you running a msd box? if not ground out the white wire on the harness that is suppose to be the input for it.
 

Ty 1885

Member
Re: ESC Module

This is very strange, why would Casper make a plug and tell you to use it, if theres no module ?
 

turbodig

Active member
Re: ESC Module

Stock ESC module is internal to the ECM (on the MEMCAL/Chip).

Fast, DFI and others all specify an external ESC module.
You'll need to get a 4.3 v6 external module out of a TBI 4.3 (Regular Blazer)

You'll also likely need a knock sensor from the same application.
 

Ty 1885

Member
Re: ESC Module

Thanks guys. Just got an email from Casper, they said i can use a GN 86,87 or mid 80s Camaro.
 

turbodig

Active member
Re: ESC Module

You won't get knock detection without it.

You'd have to be reeeeeealy good to tune a motor without some sort of indication of what knock was doing.
Hope you like pulling spark plugs...
 

Ty 1885

Member
Re: ESC Module

Casper said that i really need it. Also that mid 80s Camaro is perfect with TY knock sensor.
 

warmpancakes

New member
Re: ESC Module

Stock ESC module is internal to the ECM (on the MEMCAL/Chip).

Fast, DFI and others all specify an external ESC module.
You'll need to get a 4.3 v6 external module out of a TBI 4.3 (Regular Blazer)

You'll also likely need a knock sensor from the same application.


DFI gen 7 is designed to run with a GN setup only
 

turbodig

Active member
Re: ESC Module

DFI gen 7 is designed to run with a GN setup only

Not sure how it would know the difference. The line output is essentially the same, it just holds a line low when there's knock. The sensors themselves are different impedance, but that doesn't get transmitted to the ECM.
 

warmpancakes

New member
Re: ESC Module

Not sure how it would know the difference. The line output is essentially the same, it just holds a line low when there's knock. The sensors themselves are different impedance, but that doesn't get transmitted to the ECM.

I just remember when they were designing it I had to "find one" the the knock kit from DFI was gm parts reboxed
 

turbodig

Active member
Re: ESC Module

I just remember when they were designing it I had to "find one" the the knock kit from DFI was gm parts reboxed

That I can see... had to have one to do the software against. But it's really not different from the modules on other apps... they work the same way, it's just the calibration of them that differs from application to application.

Every engine is different, in an acoustical sense, so the modules need to be tuned to the application they're being used on. This provides the best amount of noise rejection, while still hearing as much true knock as possible.

The white chip on our stock MEMCAL, and these external boxes, are essentially the same critter. GM just included the knock sensor calibration with the ECM in later applications to make the thing more "modular"; replace the ECM and you get the correct PROM, CALPAK, and ESC calibration all in one thing.

The Casper's knock gauges use these same external modules.
 

JSM

Active member
Re: ESC Module

Anybody got a Buick ESC laying around? Need one for my buick and not sure where it went.

A pinout might be nice to have for this discussion also.
 
Top