failed emissions

carVSsuv

New member
got my first ty last weekend and had to get it register which meant the inspection line.

I figured that it would pass because it had a tune up a within the last 2 years in which the truck has only been driven roughly 4000 miles.

Things i noticed was when the truck goes to closed loop the idle gets rough. The tach jumps around a lot and feels like there is a miss in the system. When you accelerate very slowly, you can feel the miss upto 1200-1400 rpms and then it either smooths out or disapears. Truck does seem to run pretty good while driving, but this is my first 4.3 chevy and TY. The temp guage doesnt really go above the first line above 100, so i dont know if that is normal or what. The cat is installed and is followed by a 3 inch ATR.

I have searched and came up with a bunch of ideas that people try to get through emissions, but just wanted to see if there is any updated ways of doing things..

IDLE HC was 832 need 220 pass
2500 RPM HC was 432 need 220 pass

IDLE CO was 1.25 need 1.20 to pass
2500 RPM CO was 1.41 need 1.20 to pass

Test was done with a full tank of 93. I did not run the crap out of it before i got it tested

I plan on doing a tune up since the truck did not get a lot of miles on it during the last 2 years.

Plugs, wires, cap, rotor
I have a FP regulator and will try to install that and lower the FP
Will a half tank of gas and a gallon of denature Alky help?
195 thermostate if its not already one
disconnect the IC pump

any addition suggestions or tricks to get this thing through emissions?
 

SBNova

New member
Re: failed emissions

I dont know squat about emissions testing, but when my Ty had a slight miss I tightened up the plug gap to just under .030 and it went away. Ignitions in these trucks are picky. Get some new plugs and gap them right and I bet your miss is resolved.
 

97 CAIVIAROSS

Cubes or PSI Which 1 2day
Re: failed emissions

Jeremy


When I had it tested I did the tune up, heavy duty cap and rotor from Hood, taylor wires and ngk spark plugs. There should not be any corrosion on the terminals as I used dieletric grease on all of them. It already has the silicone vacuum lines although you have the precut kits if you want to replace them. All I did was change those things and put in about 3 bottles of the gas line antifreeze and the ran it pretty good before I got there so it was nice and hot. The guy said it passed no problem. It did not have the walbro 255 pump in or the larger intercooler pump at the time. I don't think that would make a difference though. Oh, like I said I did not put in the 160 thermostat, should have a stock one in there, but was in the box with some of the spare parts.

When you do the plugs do your self a favor and buy the sparkplug socket that has the swivel built into it makes it easier.
Derek
 

carVSsuv

New member
Re: failed emissions

I am thinking that the fuel pump is causing the truck to run rich. I didnt get the chance to check anything today but i know from looking under the hood that it all looks pretty new and i know you said that you did a tune up. I will probably changes the plugs first and install the fuel pressure regulator and add a fuel pressure guage. I know you said that the thermostat was not changed, but i was wondering on the guage.

Also how the heck did you get the datamaster to work. It says it can not sync to PCM?

the recheck line is shorter so thats not bad.

I hate emissions.. my old beater truck passed with flying colors..
 

97 CAIVIAROSS

Cubes or PSI Which 1 2day
Re: failed emissions

carVSsuv said:
I am thinking that the fuel pump is causing the truck to run rich. I didnt get the chance to check anything today but i know from looking under the hood that it all looks pretty new and i know you said that you did a tune up. I will probably changes the plugs first and install the fuel pressure regulator and add a fuel pressure guage. I know you said that the thermostat was not changed, but i was wondering on the guage.

Also how the heck did you get the datamaster to work. It says it can not sync to PCM?

the recheck line is shorter so thats not bad.

I hate emissions.. my old beater truck passed with flying colors..

You can hook up a hand held fuel pressure gauge right to the fuel rail and check when you install the adj fuel pressure regulator.
I was never good at the datamaster and called Eric to walk me through it the two times I used it myself after doing the mods to make sure everything was still running the same. I am sure someone could chime in that is alot more knowledgeable. Sorry.
 

Don W.

Stab it and steer it
Re: failed emissions

I threw enough parts at mine to make a new truck :rotf: What it came down to was a smog tech who new his stuff explained that the (6 month old cat, purchased on EBay) was bad. One new cat later passed just fine.

Tell me this: On your paperwork what are the O2 numbers. If I understand correctly they should be low. If they're high the cat's not doing its job.

Full tuneup, set timing a bit retarded, leave brown wire disconnected, check O2 sensor readings.

All just my :2cents:
 

carVSsuv

New member
Re: failed emissions

I just wanted to update this for the people that might have this problem in the future. I know its hard finding exact answers on here sometimes so here is some info.

I passed emissions today and figured i would change the least i can and see what it does.

I install a AFPR and had my fuel pressure set to 35 psi with line off.
I disconnected the tan wire (it did turn on the check engine light)
I adjusted the idle to 900 rpm with the tan wire disconnected

I search for the check engine light wire at the computer for 2 hours an couldnt find it so i took the insturment cluster out and followed the connection point to the wiring harness and then cut the wire (Dark brown with white stripe). I added 2 wires to this to extend the original wires and put a small switch next to the fuse box where I could turn the light off for these kinda days.

I then drove it the crap out of the truck the long way to the DMV and pulled up to the inpection shack. It passed with no problems.

HC at idle
needed 220
before 843
now 0

HC at 2500 RPM
needed 220
before 432
now 1

CO at idle
needed 1.20
before 1.25
now 0

CO at 2500 RPM
needed 1.20
before 1.41
now .41

The wires, cap, rotor, plugs had less than 4000 miles on them so I didnt changed them. The stumble that the truck had when the tan wire was pluged in went away when disconnected.

So if this helps i hope it will as everybody knows that changing something out on these trucks is a PITA

:tup:
 

BigBadSmoosh

Picking fights on I-65 since 2013
Re: failed emissions

reconnect the brown wire, the solution was most likely the fuel pressure regulator.. the stock ones tend to be iffy sometimes.. now the motor is getting a constant fuel pressure and isn't having any problems.

nothing else you did would have really fixed anything, as for cutting wires.. to each their own..

I was going to suggest dropping the fuel pressure and running some gas line antifreeze to help lean out the HCs..

if you adjust the AFPR and get it running just right (not to rich, not to lean) you might even be able to pickup a few tenths at the track.. I believe that truck ran a 13.5 at its best (beating me and my 13.6).. then again, I haven't touched my trucks tune in over two years, that reminds me my typhoon is due for inspection in january.. terrific.


one more thing, since these trucks are obd I there isn't a whole lot the dmv can check by plugging into it, basically all of the stuff we see in datamaster/tunerpro and thats it.
 

carVSsuv

New member
Re: failed emissions

This wasnt ment to be the fix for everybody. It was just to help out people with issues in the same area and emission problems... You you guys in cali, well let nots even talk about vechile inspections out there. I am orginally from AZ and they were pretty bad there as well with the dyno.

THe FPR was not stock it was a bosch. However, i didnt check the fuel pressure on it first because i was going to put the AFPR in it anyways.

I did the best with what i had, and since i didnt have a wideband, i could really adjust the fuel the right way. I dont think by just adjust the pressure you can really really know how the truck is running unless you have a wideband. I had a gallon of denatured alky in the truck just in case i would need some. However I didnt want to put alky in the tank and have it possibly cause some damaged to seals and lines or have the truck run like complete crap because of the wierd fuel situation.

I dont really know if the Check Engine Light would have been a big issue with the guys or if they even look for it. Since i am not from DE originally, i listen to the guys i work with the have lived here for a long time. A check engine light could cause you to fail so try not to have one. So i did what i did.

The Datamaster that came with the truck for some reason doesnt want to sync to the pcm so i was out of luck there. If somebody (eric) wants to let me in on the secret that would be great because i could really use the extra monitoring to keep up with the truck.

I believe the track is closed now, but i wanted to go run it and see if i can beat Dereks 13.7 (his personal best in the truck). He still has the picture and time slip from that day.

Instead of just starting the swap out plugs, wires, rotor, cap and still be in the same boat, i figured i would try some of the things others have after changing everything to see if the fix might just be that quick and simple. Of course i didnt keep driving with tan wire out. In fact i pulled into the neighbor hood right before the DMV, unplugged the wire, adjusted fuel pressure and disconnected the CEL. Drove1/10 of a mile to the reinspection area, had it inspected and tested and then pulled into the parking lot of the DMV and turned the truck off. Connected the brown wire, the CEL, started the truck and Readjusted the fuel pressure right there. I am pretty picky about driving my stuff messed up.

I got all of the front end done but the ZQ8 box because the pitman was seezed on it. I ended up breaking a 5 ton puller trying to get it off and no go. But it feels a lot better now.
 
Last edited:

rodent

Member
Re: failed emissions

DaveP6999 said:
In California the smog test includes checking that the SES (Check Engine) light is functioning. Your 'fix' would fail, if the guy is doing his job...

Interesting that keeping the timing retarded, and and advancing the idle speed resulted in the improvements that you document. But obviously you don't leave it this way, because it's probably a dog without any timing advance (brown wire not connected).

Dave P

Easy fix for this. Just hook up your SES light to your brake light. The brake light will come on for a second for a 2nd when you first start your truck then go off. I had to do this a couple years ago when Colorado was checking for the SES functioning. I had a Accel DFI so no SES light ever came on. The brake light wired to the SES did the trick and passed the e-test.

Another option for passing if you're high is running a 30% mix of e85. I had problems passing my Eclipse the other day so I ran e85 along with wiring up my wastegate wide open so no boost ever took place. This really helped it to pass.
 

97 CAIVIAROSS

Cubes or PSI Which 1 2day
Re: failed emissions

Jeremy

Glad to hear you got it to pass without just throwing parts at it. That is awseome you got the front end done!!!:tup: It has to track sooo much better, especially with the steering shaft. I should have given you the paper/receipt for the zq8 box, I bought it off of a member on the board. I will see if I can search on here, maybe he can shed some light on getting the pitman arm off. I am sure you tried different things but did you try heating it up? or soaking it with PB Blaster for a day or so. You are correct on the time 13.7 was my best with a 1.7 60' with the z06 wheels.

Derek

Just searched bought it on 11/30/06 from GarnetTy1473.
 

carVSsuv

New member
Re: failed emissions

I absolutey hate emissions and think its pretty stupid considering that there are place in the state that dont require them. It should be all or none.

Derek, you would laugh at what we did to try to get it off. We did soak it with penetrating oil and it didnt work. I didnt heat it up because i didnt have a torch. We hade a 1 inch ratch on the puller and a 4 foot pipe to that and the bolt broke on one side and the other arms ended up bent to crap. The pitman didnt move, but to tell you the truth.. I dont think i want to under go that operation again. That was a PITA to do and the amount of stuff that had to be taken off to do it clean and to get access to everything was a lot. I dont think i want to under take that adventure again for a long while. Plus if i told my buddy that i was doing that again, he probably wouldnt talk to me for 2 weeks. We were both soar for 4 days after that. The truck trakes so much better and the sway bar really helps as well. THe big tires like to get sucked into the ruts, but you can now drive it and enjoy it more. But i judge the truck pretty hard because you know what have as my daily and how that handles. SO i keep telling myself its not that high performance. :D
 

97 CAIVIAROSS

Cubes or PSI Which 1 2day
Re: failed emissions

carVSsuv said:
and hey what are you doing with my truck on your screen name. LOL..

J/K :tup:

Hahahaha!!! I will have to take it down, and you can put up one. I figured you tried everything (seemed very mechanically inclined when I met you) but just thought I would ask. It will catch the ruts in the road, with the wider tires, my Camaro is all over the place on roads where there is alot of truck traffic. I wish you lived closer I would have helped, and it would be nice to see how it drives withe everything done.

Derek
 
Top