false knock?

johne30m3

Junior Member
Ok I still haven't installed any of my tuneup parts yet or checked for any loose metal objects rattling, but I have been driving my truck around lately and doing some runs with my scan master 3 . I notice that at times I get more kr than others and yes I do try to keep the iat's the same to achieve consistency . It seems that I get more kr on my first runs and then it seems to taper away to little or no kr afterward why? Also is it normal to get kr just revving in park? I get 2.5-3 kr just blipping the throttle sometimes but not always, if I rev it higher I have seen the kr jump to 8-11 . So does this sound like false knock. Also when driving at part throttle 6-10 #'s of boost no kr at all.
 

Flyin Ryan

hated cuz he drives fords
Re: false knock?

Sounds like false knock to me but you should look at the fuel and trans lines. I took heat hose and cut it down one side and put it over the lines in the questionable areas. Also check to make sure your downpipes not tapping on the frame rail.

Could try filling it up with some 93 or better fuel and do the same driving habits and see if the kr goes away
 

johne30m3

Junior Member
Re: false knock?

Well I changed all ignition parts new ngk UR5 gapped .028, brass cap+rotor, new plug wires, timing set and it seems like I have more KR than before like 2-6 degrees. I don't have DM so I'm using my scanmaster 3 . The only other thing thats different from before is that I had used built 700r4 installed with a 9/11 2800 stall and a racetronix pump relay to go with the 255 walbro that was already on the truck. Heres a little info on my truck - stock chip, 255 walbro, AFPR, Jabsico IC pump hot-wired with rubber heater hose rerouted thru pass.fender, RPM 3" catback exhaust and still running cat. I have been doing pulls with iat's between 85-105 degrees with 13-15 # boost according to my autometer gauge which also what my scan tool is showing. Also my fuel pressure is raising 1# per # of boost with my base fuel pressure set at 43#'s. I don't have a wideband yet. At WOT my o2 mv are at 950. I have checked for loose exhaust parts, checked dp to make sure it was secure and not hitting anything, checked trans lines and fuel lines. Everything seemed to be ok, the fuel lines are still secured by the brackets that bolt them up over the tranny. They don't seem to be loose, but when they go over the bell housing I lose track of them. So today I tried some 100 oct, tank had about 5-6 gallons of 93 still so I added 7.5 gallons of 100 oct. Well no luck the KR is still there and seems to be the same as before. I did look at my motor mounts, the driver side one looks all dry rotted and shot. I then brake boosted the truck with the hood open and the motor is moving a lot , like drivers side moves up 2-3". Would the motor mounts be my problem? Even if that was my problem how would it keep a consistent KR reading, I can see when it first moves but will it move back and forth? When your ac hoses rub thru the hood liner is that also a sign of bad motor mounts? This truck is driving me crazy, I just want it to run knock free. At this point I don't know what else to look for, maybe I'm just over looking something? Please if anybody has any ideas please throw them at me or if anybody who lives close is willing to help that would be cool!
 

johnboy89

Member
Re: false knock?

The fact that you filled it with 100 and still have it sure seems like false knock!!

What do you have for a chip in it? Make sure it's seated properly as this will cause knock issues also.

My motor mounts move like yours and I don't see the kr in park, but that still could be a cause

Where are you in CT? I'm in western RI, by no means an expert, but sometimes a second set of eyes does help.

Here's a helpful thread:
http://www.syty.net/forums/showthread.php?t=71730&highlight=knock+park
 

johne30m3

Junior Member
Re: false knock?

The fact that you filled it with 100 and still have it sure seems like false knock!!

What do you have for a chip in it? Make sure it's seated properly as this will cause knock issues also.

My motor mounts move like yours and I don't see the kr in park, but that still could be a cause

Where are you in CT? I'm in western RI, by no means an expert, but sometimes a second set of eyes does help.

Here's a helpful thread:
http://www.syty.net/forums/showthread.php?t=71730&highlight=knock+park

johnboy89 I live in Naugatuck , which is about 1hr 15 min from RI line going up 95. I'm running the stock chip for now until I get this figured out. I'm leaning toward false knock also because of the 100 oct fuel, but I guess it wouldn't hurt to check if the chip is fully seated.


Thanks John
 

dgoodhue

BuSTeD 4.3
Re: false knock?

If it stays the same with 100 oct it is false. It also should not have knock from reving in neutral.

Check to make sure the downpipe bracket bolt on the bell housing is installed. Signs of a bad motor mount is cut upper radiator hose and broken shroud.
 

wildphil

I Love My Ty's
Re: false knock?

First it would be a good idea to repair the motor mount issue. If is is broken. The movement of the engine could be causing something to be moving or coming into contact with something it normally would not. You could use one of the engine tie downs is you don't want to replace the mount.

I had a problem with false knock that turned out to be the fuel lines. They didn't seem to be loose at all. But I went ahead and put a old heater hose around them as was suggested in a previous post. That took care of my false knock.
 

johne30m3

Junior Member
Re: false knock?

First it would be a good idea to repair the motor mount issue. If is is broken. The movement of the engine could be causing something to be moving or coming into contact with something it normally would not. You could use one of the engine tie downs is you don't want to replace the mount.

I had a problem with false knock that turned out to be the fuel lines. They didn't seem to be loose at all. But I went ahead and put a old heater hose around them as was suggested in a previous post. That took care of my false knock.

On what part of the fuel lines, next to the bell housing? What is the easiest way to get some hose around them? Would I have to drop the tranny? Thanks guys
 

wildphil

I Love My Ty's
Re: false knock?

On what part of the fuel lines, next to the bell housing? What is the easiest way to get some hose around them? Would I have to drop the tranny? Thanks guys

You can split the heater hose lengthwise. It is hard to get at but I installed the hose on the fuel lines from the fuel rail to the the 1st clamp. You won't need to take anything loose.
 
Top