FAST - ESC testing - help please

G

Guest

Guest
My ESC system does not work. I have beat the living hell outa the upper intake with a rubber mallet, and then the alternator housing with a steel hammer. I CANNOT get the damn thing to show any ESC retard. I have a large sledge hammer, but really hate to further "dent" the powdercoating.

I spoke with Jim @ PTE today and got info regarding all leads and voltage requirements. I found a ground lead that was open to the ESC module and repaired that. NO difference. I tested the stock SyTy knock sensor as per the Sy supplement, and it tests ok (shows voltage if ya beat on the motor while in the 2v ac mode, with the connector undone). All leads to the knock sensor, ESC module and to the ECM
are now good. I also borrowed another known good ESC module from a local TB friend, and still no difference while whipping the shit outa it.

Harry wasn't in, but Jim mentioned that Joe thought that there is a place in FAST where you tell it you have a knock sensor. The only thing I have found is the ESC parameters which are filled in. Is there some secret hiding place that I haven't found?

Short of ramming this MF'r into a telephone pole while recording a run, anyone have any other ideas?
 

Windedv6

Ty n 10s
Lucky you...to at least realized that you aren't showing any knock retard. I wiped out my motor day one with FAST because my MSD distributor pickup was faulty and the DFI showed no problems or retard.

Setting up all the driveable tuning stuff went great. Then started to work our way up in boost.... Started detonating bigtime, but showed no knock or esc retard. Haven't worked on figuring it out as I have a motor to rebuild.
 

turbodig

Active member
On 2001-12-20 22:24, Roland Black wrote:
My ESC system does not work. I have beat the living hell outa the upper intake with a rubber mallet, and then the alternator housing with a steel hammer. I CANNOT get the damn thing to show any ESC retard. I have a large sledge hammer, but really hate to further "dent" the powdercoating.

I spoke with Jim @ PTE today and got info regarding all leads and voltage requirements. I found a ground lead that was open to the ESC module and repaired that. NO difference. I tested the stock SyTy knock sensor as per the Sy supplement, and it tests ok (shows voltage if ya beat on the motor while in the 2v ac mode, with the connector undone). All leads to the knock sensor, ESC module and to the ECM
are now good. I also borrowed another known good ESC module from a local TB friend, and still no difference while whipping the shit outa it.

Harry wasn't in, but Jim mentioned that Joe thought that there is a place in FAST where you tell it you have a knock sensor. The only thing I have found is the ESC parameters which are filled in. Is there some secret hiding place that I haven't found?

Short of ramming this MF'r into a telephone pole while recording a run, anyone have any other ideas?

Roland,

Do you have any knock counts when you beat it
with a hammer, or are we talkign about a
speed pro setup?


Dig
 
G

Guest

Guest
hey Dig;

It's SpeedPro, FAST, Federal Mogul, whatever. It uses the stock SyTy knock sensor with an TB ESC module and of course the SP ECM.

Winded;

Ouch........ sorry dude!
 

smeagol

Active member
Were you running the engine while you did this?

What RPM? I wonder if the FAST has a RPM limiter, to possibly eliminate the possibility of knock retard occurring at a noisy engine startup. I'd run the motor at 1500, and try it, 2000 and try it...etc etc.

Brian G
 
G

Guest

Guest
hey Brian;

I tried it first with the key on, engine not running. Doing it alone, I hit the space bar to record a run and then went up and beat on it. Not getting any results there, I tried it at an idle, with no results there either.

I'll try tomorrow at a higher rpm, plus hopefully Harry might be in and have some input. Thanks BG.
 
G

Guest

Guest
******* from Craig Smith @ TBBB********
You can test the ESC input on the FAST ECU by touching pin H1 to ground. If your harness has the ESC input wire in it, just touch it to ground to activate it. When looking at the laptop, you should see the maximum allowed amount of timing retard being applied.

This test should help narrow down the source of the problem.


__________________
Craig Smith
FAST Electronics
*********************************************

I haven't yet tried this.... went out to do so and found that in last nites frustration I left the passenger door and glovebox open. Battery charger is now at work as I type. Just an fyi on the above for others who may wish to test their system.
 
G

Guest

Guest
Ok, I put a ground to the ECM on pin H1 and the knock retard on my laptop screen DOES show 17* retard which is what is programmed into it! YEA! Progress is being made.

I'm awaiting a response from Craig as to any simple way of checking from the sensor to the ECM........ I'll share what I find out.
 

4C FED

Absolutum Dominium
Since the sensor is a microphone, I would say you could put a voltmeter, + lead, on the end of the ECM harness and the - lead to ground. If you tap on the alt. bracket, you should see some sort of voltage swing.
 

turbodig

Active member
On 2001-12-21 18:47, 4C FED wrote:
Since the sensor is a microphone, I would say you could put a voltmeter, + lead, on the end of the ECM harness and the - lead to ground. If you tap on the alt. bracket, you should see some sort of voltage swing.

Better yet, run it into the mic input of a
laptop, and see what you hear.

My bet is an open in the harness between
the Speedpro/FAST ECU and the sensor itself.

Later,

Dig
 
G

Guest

Guest
hey Rick;
I agree with most of what you say. I have got a voltage swing directly at the knock sensor. I have verified that the wiring is good from the KS to the ESC module.

Then is a guess, but I believe that the ESC module is kinda the Capt. of this ship and receives a voltage signal from the KS, and determines if it's real or not........ if not, it's ignored. If yes, then IT sends a ground to the ECM (not voltage) to remove timing. The above is a concensus of three enthusiasts who REALLY don't know :wink:

Dig;
I like that microphone input to a laptop, just wish I knew how to do it. I have verified continuity thru all wiring, it's good! Wish I knew how to verify that the ESC module is working.

Any of you TB folks out there have a service supplement that mentions how to do the above?

Thanks folks for the advise. I'm beginning to believe that finding the open ground in the wiring harness was the culprit, and that "banging" on the motor just ISN'T the correct signal so the ESC module won't pass on a ground to the ECM.......

But, I also believe in Santa too, so....
 
Top