faster at part throttle?

Gnocide

turbo game burt reynolds
anyone tune an almost stock truck and find out at wot @approx 15 psi the truck seems like its not taking all the air? letting up on the gas to about 3/4 the speed and boost pick up quicker. any ideas why? btw atr cold air kit ,fp set at 47 psi, 02 volts 950 range.
 

Gnocide

turbo game burt reynolds
ok common ground. now for the funny part. it wasnt always that way. recent changes for my ty were....... airfoil, hard turbo to intercooler pipe, throttle body spacer. now when it did run wide open,i had factory airbox. btw my boost is controled manually to 16.5psi . one more tidbit, my chip doesnt look stock however noone (chip manufactors) can identify it as theirs. ive got numbers though they are hand written.
 

Syclone#1992

SyTy.net Moderator
gnocide said:
my chip doesnt look stock however noone (chip manufactors) can identify it as theirs. ive got numbers though they are hand written.

I would definately confirm what chip you have in there. Chips can be deadly.
 

Gnocide

turbo game burt reynolds
same chip since i bought it,4 years now. thought it was stock ran several times a dozen or more 13.7 1/4 . the people with tys who ive rode with say it definitely spools faster than lets say the ultimate chip or kennebell. but i think its the boost control. anyway why would it act like it cant take any more air at 15 psi now when before i couldnt get enough air at 18-19psi? thats my question.the air box makes that much difference? i was faster on top end with the stock air intake because of full throttle air flow?
 

Sy769

Donating Member
gnocide said:
same chip since i bought it,4 years now. thought it was stock ran several times a dozen or more 13.7 1/4 . the people with tys who ive rode with say it definitely spools faster than lets say the ultimate chip or kennebell. but i think its the boost control. anyway why would it act like it cant take any more air at 15 psi now when before i couldnt get enough air at 18-19psi? thats my question.the air box makes that much difference? i was faster on top end with the stock air intake because of full throttle air flow?

This is not a flame This is being realistic. You need to go do a bit of reading on how fueing for these trucks is calculated. If you still have a stock 2 bar map you should not be over 15psi. I haven't a clue what you mean when you say you could not get enough air at 18-19 psi before. The only chips that will provide for fueling at this boost level use a 3 bar map. The only options for those are 1. Ultimate 2. Custom chip using the 3 bar code.
If you have a Hyperjunk,Kenne Bell ATR etc. etc. you don't have the fueling for anything above ~15psi.
 

Gnocide

turbo game burt reynolds
no offence taken. ill try to explain better. even though a 2 bar sensor similar to the gn is in the truck, like the gn when you add fuel by a high perf fuel pump ,and hot wiring it to the alt by the way of a bigger dedicated wire ,as much as 20% more or 2+ volts is added to the fueling system. now the hard part. gauging from exhaust temp and 02 volts and fuel pressure you can surpass 15 psi easly . my gn can do 25+ psi even though the factory maf can only calibrate 255ml per min.stay with me, the factory wastegate solenoid is not hooked up to the hoses ok. its manual, so as long as i got fuel, and im rich and exhuast temp is resonable and kr is very very low ,im safe. but no one yet has answered my origanal question.
 

JSM

Active member
Yes, you can get a 2bar to run with enough fuel or even rich above 15psi.

What that means is at 15psi it is REALLY rich. That hurts performance.

The added voltage, etc all help, but is still a bandaid fix.

Maybe when you close throttle some, fuel is calculated more closely to engine desire (not the OVERLY rich mode), hence truck runs better.
 

Gnocide

turbo game burt reynolds
makes good sense. i could always lean the fuel pressure out .im not claiming to run 20+ at all times on this 2 bar sensor. i dont even know what chip is in the thing . i just want to know what would cause the truck to act like its holding back under wot. maybe ill try less fp. poss 43lbs? what do you guys think?
 

Syclone#1992

SyTy.net Moderator
What are all your mods?

Personally if this was my truck I would do the following of you haven't already:

Walbro HP 255 Fuel Pump with AFPR
Go to Stock Chip with Stock 2 bar
Get Datamaster and tune with stock boost and chip.

Then I would get a 3Bar Map and Chip from either Dig or BG so you can run higher boost and continue to datalog with datamaster. This recipe has been proven to have sucess.

Read this:
http://www.sportmachines.com/maintenance/recipe1.html

Not that you are wrong, but I think this is the best way to go because many people have had sucess with it.

just my 2 cents,

Good luck,
 

Mephisto

These trucks are cursed
so if i have the same problem... does that mean that when i run my truck at the track, i should try and run it at 3/4 throttle or wherever the "sweet spot" is, instead of WOT? or should i try to fix the problem and tune it to run tip top at WOT?
 

Falco

Donating Member
gnocide,

One simple question. Do you have a scantool!? Have you made any recording? Post the results here... Would be easier to help that way. :wink:

IMHO, that's definately not normal, my Sy has never done that, even in stock form, 2 bar or 3 bar or whatever...

Later,
 

Gnocide

turbo game burt reynolds
problem solved . read new update phoonerorlater, vortecfiero,njty180, phoonty, and 666sothis666. maybe this will help some of you guys.
 

sytyfreak

New member
I thought that I was making up things till I readed this post :eek: Add me to that list too... It seems that the truck just sounds like its making more power but you can feel that as soon as your letting off the gas the truck is pulling harder than at WOT :(
 

vortecfiero

New member
thinking out loud....
if the stock throttle body is able to flow 800 + cfm at a max velocity of 450 ft/min
that would mean that if you only demand about 300 to 500 cfm the velocity is
really low and cyl filling not as good? and at 3/4 throttle (say 600 cfm ablility) the velocity
will go up filling the cyl faster
or does that only apply to nat asp

does the timing table back out advance under wot and boost ?
 
me too on the 3/4 faster deal.
not detonating, mounts good, and chained.
just snappier at 75%.
i run ultimate/3bar, 20g, usual bolt ons, all sensors fresh, etc.
200k miles, valve covers never been off.
 

nightdiver

Active member
Just like Falco said....use a scan tool and record the timing and the OS milivolts @ 70% throttle and at WOT @ the same boost level and rpm
Propably 3-4 runs and youre done
 
Top