flash chips source

kwick6

Donating Member
We don't have any info on this in the archives so I thought I'd ask.


I've found the Atmel 29C256 for $5


And I think we need the 150ns speed correct? I saw that a 200ns is available from digikey, but not sure if its necessary.

Also, I'm looking to modify a memcal with a zif socket, anyone found a good one that works well? got a part #?


TIA,
Scott
 

InvisiBill

Active member
http://syty.net/phpBB2/viewtopic.php?t=16890 has a link to http://www.thirdgen.org/newdesign/tech/promintro.shtml which has tons of info. Craig Moates sells ZIFs on the bottom of the page you linked to... http://www.thirdgen.org/newdesign/tech/images/prom/1138099.jpg is a shot of what your modified MEMCAL should look like... Basically just unsolder the PROM and replace it with a ZIF. You'll have to cut off half of the blue protective cover, as the ZIF and PROM won't fit under it. I was thinking the other half of the MEMCAL stuff was for ESC, and vehicle specific. I haven't seen any pre-made ones for sale anywhere...

From other threads, I've picked up that our ECMs have problems with PROMs faster than 120ns, depending on the brand. Note that this is time, so a bigger number means it's a slower chip. I'm not sure what the minimum speed is, but you probably don't want to go any faster than 120ns, just to avoid any potential problems. Or talk to someone who has experience with them, and can recommend a good <120ns brand...
 

turbodig

Active member
Re: flash chips source

kwick6 said:
We don't have any info on this in the archives so I thought I'd ask.


I've found the Atmel 29C256 for $5


www.jdr.com has them for that price as well. Same difference.

And I think we need the 150ns speed correct? I saw that a 200ns is available from digikey, but not sure if its necessary.

JDR screwed up and sent me some -90s that seem to work, I'd bet
90 or higher will work in the Flash EPROMs.

Also I tried an AMD 29F040 and it seems to work fine in the Ultimate
box I have here, FWIW. Haven't done any WOT testing in the truck
with it, but the ECM powers up just fine.

Also, I'm looking to modify a memcal with a zif socket, anyone found a good one that works well? got a part #?

IMO, you're better off getting the setup from Craig Moates. It's cheaper
than a memcal.

If ya really gotta, go buy a 28-pin socket from Digi-Key, and a 28-pin ZIF.

Clip the leads on the stock EPROM off. (cut 'em as close to the body
of the chip as possible)
Pull the ceramic "body" of the chip off, and heat the little bits of lead that
are left with your soldering iron. They eventually fall right out.

Once you have all the lead chunks out, make sure you have no solder
globs shorting adjacent pins. Take the 28 pin socket, and push it into the
carrier where the old EPROM was. Push hard, it should seat flush with the
carrier.

Once it's in there, dab some solder on each of the socket pins where they
contact the carrier. You should have a good puddle in each "pocket".

Push the ZIF down into the regular socket, and you're done. You can
pull the ZIF then, if you need to use it for a regular EPROM.

My .02.

Later,

Dig
 

kwick6

Donating Member
Just bought a spare ecm, with a stock memcal in it. Went and got the low profile 28 pin socket from radio shack for $.99

Anyway, looking closer at the stock memcal, I noticed a small crack in one end. :evil: Tough to see in the pic, but you can see how the left side is kinda Fd up.

Is it worth trying to use?

abu.sized.jpg
 
Top