Help with Check Engine Light - No Codes

Rhube

New member
Hi fellow SyTy'ers. I've owned a Syclone for about 5 years now and came across syty.net a couple of years ago, but have been a "lurker" on and off since then. My truck is stock with the exception of an ATR catback system, Pitbull chip, and a Johnson intercooler pump (hot wired) and currently has ~45,000 miles on the original engine. It get's stored in the barn during the winters and driven when the weather gets nice.

Last weekend, I took it out of it's winter slumber in the barn for a liesurely drive around in hopes that spring will get here soon. After charging the battery the truck took a number of cranks to start, but finally did, and ran really well. Took it to town and put a splash of fresh fuel in it and drove around for a bit. Just before I got home, I leaned into the throttle a bit (not quite to the floor) and the engine sputtered a little bit and then died. Both the Check Engine and Check Gauges lights went on at the same time. Keyed off and tried restarting but to no avail. It would crank but never fire. After pulling it home, I jumped the A and B pins on the ALDL to check for codes, but only got "12" to show up (blink 12 three times, then would continue to blink 12). Is it supposed to constantly blink "12" if there are no codes? I'm not sure where to start on this one. It seems to be getting fuel as the fuel "rail" had fuel in it, though I don't have a fuel pressure gauge right now to check fuel pressure. Not sure if it matters, but plugs are NGK UR5, wires are Taylors, cap and rotor are Conrad, and ignition module was replaced a couple of years ago. The engine has always run very well for me with the exception of a rough idle that was cured with a tune up.

Any ideas where to start or what to look for? Any help is greatly appreciated.

Thanks!

Paul
 
Re: Help with Check Engine Light - No Codes

fuse for fuel pump. if good, listen for the fuel pump to prime when to turn the key to the on postion. it sounds dumb but check the air filter and intake tube. something could have made a home in there over the winter.
 

Rhube

New member
Re: Help with Check Engine Light - No Codes

Thank you for the tips!

I finally had some time today to investigate this issue further. Just to check, I tried starting the truck figuring it would still crank and not start, but it fired right up. After shutting it off, I checked the fuel pressure and it read 40 psi at key on, so the fuel pump appears to be working alright. I didn't get a chance to take the truck out for a drive due to the weather. I'm going to try to take it for a spin tomorrow to see if the same thing happens again.

Any ideas why it would die on me, then not start that day even after letting it sit for a while, and then it starts perfectly today with nothing done in between other than disconnecting the battery?

Thanks again
 

Quickstop [UK]

Combating adversyty.
Re: Help with Check Engine Light - No Codes

disconnecting the battery cleared your codes. You'll need to wait for it again and see if it does it again. Maybe it won't.

Checked all your connections? Grounds etc?
 

SikVSix

New member
Re: Help with Check Engine Light - No Codes

ign module getting hot? seems like I've read about that being fairly common. make sure its got the grease under it when replaced etc.
 

Rhube

New member
Re: Help with Check Engine Light - No Codes

Thanks for the help guys! I replaced the fuel filter last year so it only has a couple hundred miles on it (if that)....not saying that couldn't be a problem, but less likely given the good fuel pressure check.

The ignition module was replaced relatively recently (a year or two ago) but the more I've read about them on here, the more I question their reliability. I was thinking along the same lines about something getting hot and that causing the issues. I honestly can't remember how I installed it or if I put grease under it or not, so I'm going to check into that.

Thanks again for everyones help
 

Big Mike

New member
Re: Help with Check Engine Light - No Codes

How old is your stator in the distributor? They seem to fail when hot and work when cooled off.
 

Rhube

New member
Re: Help with Check Engine Light - No Codes

I'm a little more confused than I was before. After the truck fired right up as I mentioned in my last post, I tried to take it for a drive a couple days later and it wouldn't start again. I had already ordered a new ignition module so I installed that last night, and after a few cranks the truck fired up again. Once again, the weather wasn't cooperating last night so I did not drive it at all. I went out again tonight to drive it, but again it would not start. I noticed tonight that when the engine is cranking, the tach is not moving at all...dead at 0 rpm. Would a bad pickup coil match these symptoms?
 
Top