how it works

BMFB

Not to scale
ok, ive been looking around and i understand what code59 is, and basically how it works. my question (and im embarrassed to ask it) is how is it actually hooked up

it looks like i have to go into my ecm and modify the stock chip or replace the stock chip entirely with a socket that i connect a cable to that runs to an emulator, on that emulator is the setup that ive programmed onto it with a program such as ostrich, and ive programmed it using information ive gathered from something such as tuner pro, which is hooked up through an aldl connector to a usb port on my lap top,

im also guessing that ostrich is hooked up through a usb...

the emulator is always there, acting in place of my stock chip, and when i want to change it i just plug a laptop in and go.

so, that being said ive been looking on the moates site and its kinda tricky to find exactly what im looking for, because im not sure exactly what it is im looking for, i understand i need to get my hands on some kind of G1 or G3 adapter, which is what looks like goes in my ECM board, and then a cable to go from that to the emulator, then the emulator itself, which its lookin like im going with an ostrich 2.0, and then a cable going from that to my laptop.

then, i need an aldl to usb for data gathering and whatnot

now, what am i missing from that? or am i totally wrong on my guessing of how it works.

i know ive been asking alot of questions, but i wanna make sure i don't screw this up, cause im doing it here as soon as i can, im just hoping i can get some decent results, considering its a totally stock truck otherwise
 

NecroWolf

lost marbles member
Re: how it works

you buy a thingie that plugs into the ecm thingie and use a cable thingie and adapter thingies to hook to a computer.
 

BoostedSUV

Active member
Re: how it works

That sounds about right to me. G1 or G3 adapter that piggybacks the stock chip with the ostrich emulator 2.0, a usb cable from Ostrich to laptop to program the ostrich, a ALDL cable from ALDL port to laptop to "read" what the truck/ECM is doing and tunerpro to make changes to the tune and program the Ostrich.
 

BMFB

Not to scale
Re: how it works

which would work better, the G1 or the G3, also i looked around and couldn't find them on that website, if you could point me int eh right direction, id be super happy

-Brian
 

Poconojoe

Donating Member
Re: how it works

which would work better, the G1 or the G3, also i looked around and couldn't find them on that website, if you could point me int eh right direction, id be super happy

-Brian

You can always call Craig at Moates and tell him what you want to do and he'll point you in the right direction. He's not the easiest guy to get on the phone, but you could always email him at support@moates.net I bought the APU1 AutoProm, its an all in one package, and allows you to burn an image to a flash chip, when you're done with the tune and then put the chip in your ECM, so you don't have to drive around with your emulator hooked up
 

WyoSyclone

Active member
Re: how it works

I use...

The GP1 chip carrier - includes the ZIF socket and a couple of chips...
http://www.moates.net/product_info.php?cPath=73_64&products_id=41

And I use the older Flash n' Burn to program chips... this is the newer BURN2
http://www.moates.net/product_info.php?cPath=73_64&products_id=197

And, if you want to do real-time emulation you can buy the Ostrich (it will plug into the G1 chip carrier in place of a programmed chip).
http://www.moates.net/product_info.php?cPath=73_64&products_id=169

Truthfully, I've only used the Ostrich once or twice as I like to do a log, then take it back to the shop and study it for about an hour, make the mods to the BIN in TunerPro, burn a new chip, and then go do another log.

And this cable plugs in between your OBD connector and your laptop for datalogging...
http://www.moates.net/product_info.php?cPath=73_64&products_id=128

Or... This is the newer AutoProm that does all of the above in one unit (but you still need to purchase a G1 chip carrier).
http://www.moates.net/product_info.php?cPath=73_64&products_id=54

Hope this helps :D
 

BMFB

Not to scale
Re: how it works

so, i get the G1 adapter, solder it into my ecm, and then i can either use the chips that it came with and take them out and reburn them as i need to, or use the ostrich as a sort of remote chip, and reprogram it as i need to, but have the emulator always on board? and if i decide to go with the ostrich i dont have to buy the chip burner, and if i decide to go with the chip burner i dont have to use the ostrich (necessarily)

it seems like the ostrich is a good way to go, if i can hide the emulator and if its trustworthy enough to just leave hooked up to continuously run my truck, i can see how id want both though...
 

BoostedSUV

Active member
Re: how it works

The adapter just plugs into the ECM in place of the factory memcal, then the factory memcal piggy backs the G1 adapter since some of its functions are still used. It's a rather easy install, it's the tuning that is more involved part...
 

WyoSyclone

Active member
Re: how it works

but have the emulator always on board?...

No, if you burn a chip and insert it into the ZIF in the G1 you do not have to keep the emulator on board.... you use EITHER a burned chip, or the emulator, but not both at the same time.
 

BMFB

Not to scale
Re: how it works

oh, even better

so it sounds like the emulator can just be used without worry of it failing and stranding me, which worried me

I was just making sure of what i needed, did wanna get the wrong stuff, or stuff i didnt need, thank you everyone for your help.

cant wait to actually be programming it, i know its not gonn abe easy, and gonna take a few tanks of gas worth of just 'driving around' to get it working well

i was also wondering if you guys running emulators had differant saved setups that you ran, like, if you were doing everyday driving if you had a saved program that gave you better econ, and then when you took it to the track or cruise if you just fired your laptop up and switch over to a more aggressive setup, cause that sounds like it would be neat
 

Aeroking

e.i.
Re: how it works

x2 on rarely using the emulator. I used it to set the idle, thats it. I tune by myself so i cant tune and drive at the same time, so i dont use my Ostrich anymore. ZIF socket and chips works great :2cents:

+1 bonus point for Craig Moates. :tup:
 

BMFB

Not to scale
Re: how it works

are either of the aldl cables discussed here usb? im using a newer laptop and ive always heard if you have usb ports to use them instead. In the descriptions on the product its not to specific on if there serial or usb so i thought i should ask
 

turbodig

Active member
Re: how it works

i was just wondering because they were the same price of 80 dollars

You want the combo cable... if you don't order both parts, you won't get the part of the cable that plugs into the dash.

The link you posted was the correct one.

As far as the ostrich vs. the individual chips (or both), it's more of a comfort level thing. I'd have to say the ostrich is easier to use once you've got it plugged in and running, and there's really no need to remove it.
There's a lot of mechanical things that can go wrong pulling chips in and out (bent pins, static-frying parts), that aren't always easy for someone new to diagnose. You end up thinking you did something wrong tuning, when you really just crushed a pin putting it back in.

What the guys said about making a run and coming back to look at data is true... very little tuning actually happens on the fly, unless you have somebody else driving. Even then, it's often a good idea to stop and take a look at all the data in a "calmer" environment.

I have both setups (actually many of both), but I leave the ostrich in mine most of the time. It's handy if you're out and about someplace and you notice a driveability hiccup that needs a quick change. It's also good if you want to pull/add a couple degrees of timing at the track quickly. Someday I'll get to a happiness point with the tune such that I can burn a physical chip for the Sy and leave it in there, but until then, the ostrich stays in there.
 
Top