I Need Help Reading Datamaster

Bill Z

Donating Member
Just rebuilt my motor and re-installed it last weekend. Got 80 miles on the new engine. Nothing spectacular. Quite ordinary. 30 over pistons, new stock springs and Comp Cam lifters with a stock cam. Fresh heads with new valve grind. Stock injectors with stock chip and MAP sensor. Stock, stock, stock.

It hasn’t generated any codes (yet).

It does run somewhat different now.

I was wanting to make some Datamaster files and have someone look at them to tell me if all is OK or suggest some changes.

Before I make the files I was wondering if there is certain stuff that I should be doing as I am making the files. Like should I just drive normal and easy from zero to 60 and back to zero for one run. Then launch from 5 pounds through 80 MPH letting the trans shift at will.

What are the better scenarios to evaluate the tune I got on this engine?

Let me know if you want to help and what you want to see. I will create the files and e-mail them to you.

Thanks for any help.
 

93ty475

Donating Member
Re: I Need Help Reading Datamaster

First, make sure you're knock sensor is responding to taps on the rear of the block or upper intake with a long 3/8" extension or something of the sort (ignition on, datamaster recording)....verify your timing is set to zero with the tan wire unplugged.....then just do some normal driving and some ~1/2 throttle runs while verifying you're not getting crazy amounts of knock counts on datamaster....If you're getting any measurable amount of knock counts under load, more things need to be addressed before continuing.....I'm not a total DM expert, but I'd be happy to give it a shot and take a look at your first runs if you'd like.... utwtire@gmail.com
 

Bill Z

Donating Member
Re: I Need Help Reading Datamaster

I know my timing is set to zero with the wire disconnected. What should the timing be with the wire connected?

Tomorrow morning I will test out my new home made datamaster cable and create some files.

Assuming the knock sensor test is OK, and I do some 5 minute normal driving (with no boost), should I try something at about 5 pounds of boost creating a file for each test?
 

TYTILIDIE

METH HEAD
Re: I Need Help Reading Datamaster

Ild be happy to help you out as well. I am pretty well experienced with DM. If youneed anything PM me and Ill hep youout to the best of my ability.
 

Don W.

Stab it and steer it
Re: I Need Help Reading Datamaster

:2cents: At least on my truck timing is everything. For example: On pump gas, timing to "0" = knock. Reduce timing a 2-3 degrees (retard) knock almost goes away. One of the many advantages of Datamaster. This year I'll be running alki so starting over but that's how it was last year. Give yourself time and patience and you'll be rewarded with a good running truck.
 

Bill Z

Donating Member
Re: I Need Help Reading Datamaster

I'm in deep now. To got Datamaster up and running, due to several problems. I loaded it on a friends laptop and run out of free tries. I can't find my key that I used before my laptop craped out.

I am looking for suggestions.

Please e-mail or PM me.
 

Don W.

Stab it and steer it
Re: I Need Help Reading Datamaster

1st suggestion: if you have a "paid" version, with key, get ahold of who you bought it from and they should re-supply your key.
 

Bill Z

Donating Member
Re: I Need Help Reading Datamaster

For some reason the key for v341 didn't work for v351. I found an old 341 version, installed it and that works. I don't have USB support but I don't need it on this laptop anyway.

My Ty is throwing error 35. I know that 35 is an IAC error and it means that it thinks there is a vacuum problem that the IAC can't manage to. But playing back the DM file, I see the IAC position changing and the vacuum stays above 16Hg. Shouldn't it be somewhere around 18? The idle is high at 975 when it should be 725. I figure that is because of the low vacuum.

As I said above, I just rebuilt the motor and all of the gaskets are new except the plenum gasket (I just ordered one from Tucker). My old gasket wasn't damaged, just old. Vacuum lines all replaced with new lines and elbow connectors.

So, any one with suggestions as to what should I check and how I should check to keep this code from coming back?

Your help is appreciated.
 

Bill Z

Donating Member
Re: I Need Help Reading Datamaster

Well, its Friday the 13th and I haven't a clue as what I should I can try to resolve my error 35 other than check all of my vacuum lines.

Can the O rings on the injectors get old enough to cause vacuum leeks?
What gasket sealer is recommended on the plenum gasket?
 
Top